臺灣博碩士論文加值系統

本論文提出一個具有高方向性及可調傳輸零點的微帶方向耦合器之設計，電路由二段四分之一波長平行耦合線及一段四分之一波長耦合的三階傳輸線濾波器組成，在中心頻率可產生一隔離零點以改善耦合器的方向性，且在耦合端埠可產生一對零點；藉由改變濾波器短路殘段的阻抗，可以控制此對傳輸零點。本文利用鋸齒耦合線結構使奇模和偶模的傳播相位速度一致，明顯改善了上止帶的抑制效果。本文中共有五個電路實作，並加以量測以驗證所提出設計，量測結果與模擬相當一致。

This thesis presents design of a high directivity coupled microstrip directional coupler with tuneable transmission zeros. The circuit consists of two quarter-wavelengh parallel-coupled-lines and a third-order bandpass filter. An
isolation zero is devised to improve the directivity of the coupler at the center frequency. In addition, a pair of tuneable transmission zeros are created at the coupled port. The control of these two transmission zeros is achieved by adjusting the line impedance of the short-circuited stubs of the filter.Corrugated microstrip coupled-lines are synthesized to equalize the phase velocities of the odd and even modes. It can significantly improve the rejection of the microstrip coupler in the upper stopband. Five circuits are fabricated and measured to verify the idea. Measurement and simulation results show good agreement.

第一章 緒論.......................................1
第二章 高方向性方向耦合器設計.....................5
2-1 耦合線方向耦合器基本原理...............5
2-2 具延遲線之方向耦合器...................6
2-2-1 小反射原理.......................6
2-2-2 奇模與偶模之電路分析.............7
2-3 電路模擬與量測.........................13
第三章 具可調傳輸零點之方向耦合器.................27
3-1 奇模與偶模之電路分析...................27
3-2 鋸齒耦合級特性及其方向耦合器之應用.....32
3-3 電路模擬與量測.........................33
第四章 結論.......................................53
參考文獻 ........................................ 54
作者簡介 ........................................ 59

[1] D. Wan, B. You, and L. Sun, “Radio link analysis and design of directional coupler with high isolation for UHF RFID reader,” Proc. Communication Tech. Int. Conf.,pp.256-259, Nov. 2008.
[2] W.-K. Kim, M.-Q. Lee, J.-H. Kim, H.-S. Lim, J.-W. Yu, B.-J. Jang, and J.-S. Park,“A passive circulator with high isolation using a directional coupler for RFID,”IEEE MTT-S Int. Microw. Symp. Dig., pp.1177-1180, Jun. 2006.
[3] J.-W. Jung, K.-K. Nae, J. Kim, and J.-S. Park, “RF-IPD directional coupler for mobile RFID handset applications,” Electronics Letters , vol.43, no.13, pp.719-720,Jun. 2007.
[4] J.-W. Jung, K.-K. Nae, J.-H. Bae, E.-J. Lee, H.-R. Oh, Y.-R. Seong and J.-S. Park,“Compact size directional coupler for mobile RFID reader,” IEEE MTT-S Int.Microw. Symp. Dig., pp.987-989, Jun. 2007.
[5] H.-S. Jang, W.-G. Lim and J.-W. Yu, “Transmit/receive isolator for UHF RFID reader with wideband balanced directional coupler,” Proc. Asia-Pacific Microw.Conf., pp.233-236, Dec. 2009.
[6] W.-G. Lim, S.-Y. Park, S.-Y. Lee, M.-Q. Lee, and J.-W. Yu, “Balanced directional coupler structure with insensitive isolation for load impedance,” Proc. European
Microw. Conf., pp.1280-1283, Oct. 2008.
[7] D. M. Pozar, Microwave Engineering, 2nd ed. New York: Wiley, 1998.
[8] S. L. March, “Phase velocity compensation in parallel-coupled microstrip,” IEEE
MTT-S Int. Microw. Symp. Dig., vol.82, no.1, pp. 410- 412, Jun. 1982.
[9] A. Podell, “A high directivity microstrip coupler technique,” IEEE G-MTT Int.Microw. Symp. Dig., vol.70, no.1, pp. 33- 36, May 1970.
[10] S. Uysal, and H. Aghvami, “Synthesis design and construction of ultra-wide-band nonuniform quadrature directional couplers in inhomogeneous media,” IEEE Trans.
Microwave Theory Tech., vol.37, no.6, pp.969-976, Jun. 1989.
[11] J.-T. Kuo, U-Hou Lok, and M.-H. Wu, “Novel corrugated coupled-line stage with ideal frequency response and its application to bandpass filter design with multi-harmonic suppression,” IEEE MTT-S Int. Microw. Symp. Dig., pp.553-556, Jun. 2007.
[12] M. Dydyk, “Accurate design of microstrip directional couplers with capacitive compensation,” IEEE MTT-S Int. Microw. Symp. Dig., vol.1, pp.581-584, May 1990.
[13] R. Phromloungsr and M. Chongcheawchamnan, “A high directivity coupler design using an inductive compensation technique,” Proc. Asia-Pacific Microw. Conf., vol.5, pp. 2840-2843, Dec. 2005.
[14] R. Phromloungsri, M. Chongcheawchamnan and I.-D. Robertson, “Inductively Compensated Parallel Coupled Microstrip Lines and Their Applications,” IEEE Trans. Microwave Theory Tech., vol.54, no.9, pp.3571-3582, Sep. 2006.
[15] J. Lin, “A study of microstrip coupler with high directivity,” Proc. Microw. and Millimeter Wave Tech. Int. Conf., pp.905-908, Aug. 1998.
[16] C.-S. Kim, J.-S. Lim, D.-J. Kim, and D. A., “A design of single and multi-section microstrip directional coupler with the high directivity,” IEEE MTT-S Int. Microw. Symp. Dig., vol.3, pp. 1895- 1898, Jun. 2004.
[17] M. Dydyk, “Microstrip directional couplers with ideal performance via single-element compensation,” IEEE Trans. Microwave Theory Tech., vol.47, no.6, pp.956-964, Jun. 1999.
[18] S. Lee and Y. Lee, “An inductor-loaded microstrip directional coupler for directivity enhancement,” IEEE Microw. Wireless Compon. Lett., vol.19, no.6, pp.362-364, Jun. 2009.
[19] S. Lee and Y. Lee, “A Design Method for Microstrip Directional Couplers Loaded With Shunt Inductors for Directivity Enhancement,” IEEE Trans. Microwave Theory Tech., vol.58, no.4, pp.994-1002, Apr. 2010.
[20] S.-F. Chang, J.-L. Chen, Y.-H. Jeng, and C.-T. Wu, “New high-directivity coupler design with coupled spurlines,” IEEE Microw. Wireless Compon. Lett., vol.14, no.2,pp. 65- 67, Feb. 2004.
[21] S.-M. Wang, C.-H. Chen, and C.-Y. Chang, “A study of meandered microstrip coupler with high directivity,” IEEE MTT-S Int. Microw. Symp. Dig., vol.1, pp. 63-66 vol.1, 8-13 Jun. 2003.
[22] S.-M. Wang, M.-Y. Hsieh, C.-H. Chiang and C.-Y. Chang, “Microstrip directional coupler with nearly ideal TEM coupler performance,” Electronics Letters, vol.41,no.11, pp. 651- 653, May 2005.
[23] 王士鳴，「微帶線高指向性耦合結構之研究與其應用」，國立交通大學，博士論文，民國94 年9 月。
[24] T. Jayanthy and S. Maheswari, “Design of high directivity microstrip coupler with single floating conductor on coupled edges,” IEEE Wireless Microw. Tech. Conf.,pp.1-4, Apr. 2009.
[25] S. Bensmida and F. M. Ghannouchi, “New high directivity coupler design using feed-forward compensation technique,” Proc. European Microw. Conf.,pp.191-194, Oct. 2008.
[26] C.-S. Kim, S.-W. Lee, P.-Y. Lee, H.-S. Kim, J.-S. Park and D. Ahn, “Design of re-entrant mode microstrip directional coupler for high directivity performance,”
Proc. Asia-Pacific Microw. Conf., pp.1286-1289, Dec. 2000.
[27] J. Shi, X.-Y. Zhang, K.-W. Lau, J.-X. Chen and Q. Xue, “Directional coupler with
high directivity using metallic cylinders on microstrip line,” Electronics Letters,vol.45, no.8, pp.415-417, Apr. 2009.
[28] I. Ohta, T. Kawai, T. Fujii and Y. Kokubo, “Directivity improvement of microstrip coupled line couplers based on equivalent admittance approach,” IEEE MTT-S Int. Microw. Symp. Dig., vol.1, pp. 43- 46, Jun. 2003.
[29] L. Su, T. Itoh and J. Rivera, “Design of an overlay directional coupler by a full-wave analysis,” IEEE Trans. Microwave Theory Tech., vol.31, no.12,pp.1017-1022, Dec. 1983.
[30] Y.-H. Chun, J.-Y. Moon, S.-W. Yun, and J.-K. Rhee, “Microstrip line directional couplers with high directivity,” Electronics Letters , vol.40, no.5, pp. 317- 318, Mar.2004.
[31] Y.-H. Chun, J.-Y. Moon, S.-W. Yun, and J.-K. Rhee, “A novel microstrip line backward directional coupler with high directivity,” IEEE MTT-S Int. Microw. Symp.Dig., vol.3, pp. 1891- 1894 Vol.3, Jun. 2004.
[32] V. Napijalo, “Multilayer 180° hybrid coupler in LTCC technology for 24GHz applications,” Proc. European Microw. Conf., pp.552-555, Oct. 2007.
[33] V. Napijalo and B. Kearns, “Multilayer 180° Coupled Line Hybrid Coupler,” IEEE Trans. Microwave Theory Tech., vol.56, no.11, pp.2525-2535, Nov. 2008.
[34] S. Gruszczynski and K. Wincza, “Broadband multisection asymmetric 8.34-dB directional coupler with improved directivity,” Proc. Asia-Pacific Microw. Conf.,
pp.1-4, Dec. 2007.
[35] A.-M. Abbosh, “Design of a broadband quadrature directional coupler,” Proc. Asia-Pacific Microw. Conf., pp.1-4, Dec. 2007.
[36] W. Tong and Z.R. Hu, “A super compact left-handed coupled-line directional coupler,” Proc. Asia-Pacific Microw. Conf. , vol.3, pp. 4, Dec. 2005.
[37] C.-S. Kim, C.-S. Yoon, J.-S. Park, D. A.; J.-B. Lim, and S.-I. Yang, “A design of the novel varactor tuned directional coupler,” IEEE MTT-S Int. Microw. Symp. Dig.,
vol.4, pp.1725-1728,Jun. 1999.
[38] C.-S. Kim, J.-S. Park, D. Ahn and J.-B. Lim, “Variable directional coupler with LC resonator,” Electronics Letters , vol.36, no.18, pp.1557-1559, Aug. 2000.
[39] T. Lehmann, H. Mextorf, and R. Knoechel, “Design of quadrature directional couplers with continuously variable coupling ratios,” Proc. European Microw. Conf.,pp.199-202, Oct. 2008.
[40] C. Caloz, A. Sanada and T. Itoh, “A novel composite right-/left-handed coupled-line directional coupler with arbitrary coupling level and broad bandwidth,” IEEE Trans. Microwave Theory Tech., vol.52, no.3, pp. 980- 992, Mar. 2004.
[41] J.M. Drozd and W.T. Joines, “Maximally flat quarter-wavelength-coupled transmission-line filters using Q distribution,” IEEE Trans. Microwave Theory Tech., vol.45, no.12, pp.2100-2113, Dec. 1997.
[42] Zeland Software Inc., IE3D simulator, Jan. 1997.