臺灣博碩士論文加值系統

本文主要目的以套裝軟體STRA-CD以三維的方式模擬活塞內部加裝冷卻渠道，觀察此渠道在活塞做往復運動下以及考慮自然對流效應下，渠道內部流場和溫度場的變化，並討論冷卻流體對活塞高溫壁面的熱傳增益，而模擬結果並與同步與實驗作對照，以驗證模擬的真實性。
主要探討在往復運動下的流場和溫度場之變化，以了解這類問題的運動機制，並針對不同的流場雷諾數、進口速度與振動頻率，以及加熱壁面溫度，比較其對活塞高溫壁面的熱傳增益。綜合所獲得的結果，當活塞運動後，會在活塞高溫壁面附近產生類似的牽引和推擠流體現象，使得原本附近高溫壁面上之溫度邊界層受到擾動而被破壞和縮小，熱傳效果會普遍提升。

The aim of this simulation is to investigate the variations of flow and thermal fields in the cooling channel within the reciprocating piston, and discuss the heat transfer effect of the cooling flow on the heat surface of the piston.
The STRA-CD is adopted to investigate the variations of the flow and thermal fields induced by the reciprocation of the piston. The heat transfer effects of different Reynolds numbers, and reciprocating frequency on heat transfer rate are shown and discussed. Based on the above procedures, the results show that the reciprocating piston would draw and push the cooling flow. Therefore, the heat transfer rate is enhanced remarkably.

中文摘要



…………………………………………………………………………… i
英文摘要 …………………………………………………………………………… ii
誌謝 …………………………………………………………………………… iii
目錄 …………………………………………………………………………… iv
表目錄 …………………………………………………………………………… v
圖目錄 …………………………………………………………………………… vi
符號說明 …………………………………………………………………………… viii
第一章 緒論……………………………………………………………………… 1
1.1 研究動機..........................................................................................顧.......................................................................................... 1
1.2 文獻回顧.......................................................................................... 2
1.3 研究目的………………………………………………………………… 5
第二章 物理模式………………………………………………………………… 8
2.1 物理模式………………………………………………………………… 8
2.2 分析假設與統御方程式...……………………………………………… 8
2.3 邊界條件………………………………………………………………… 9
第三章 數值方法………………………………………………………………… 17
3.1 數值方法………………………………………………………………… 17
3.2 PISO數值計算…………………………………………………………. 19
3.3 暫態滑移網格(sliding mesh)............................................................ 21
第四章 結果與討論……………………………………………………………… 27
4.1 態模擬數值................................................................................... 27
4.2 動態模擬數值…………………………………………………………… 28
4.3 動態與靜態比較………………………………………………………… 30
4.4 實驗流場可視化與模擬比較…………………………………………… 32
第五章 結論……………………………………………………………………… 66
參考文獻.......................................................................................... 67

1. P. P. Grassmann, and M. Tuma, “Applications of the Electrolytic Method-Ⅱ. Mass Transfer within a Tube for Steady, Oscillating and Pulsating Flows,”International Journal of Heat and Mass Transfer, Vol. 22, pp. 799-804, 1979.
2. S. Y. Kim, B. H. Kang, and A. E. Hyun, “Heat Transfer in the Thermally Developing Region of a Pulsating Channel Flow,” International Journal of Heat and Mass Transfer, Vol. 36, No. 17, pp. 1257-1266, 1993.
3. A. E. Bergles, “Heat Transfer Enhancement – The Encouragement and Friction in Tubes with Repeated-Rib Roughness,” International Journal of Heat and Mass Transfer, Vol. 14, No. 4, pp. 601-617, 1971.
4. A. T. Patera ,and B.B. Mikic, “Exploiting Hydrodynamic Instabilities Resonant Heat Transfer Enhancement,”International Journal of Heat and Mass Transfer, Vol. 29, No. 8,pp. 1127-1138, 1986.
5. R. L. Webb, E. R. G. Eckert, and R. J. Goldstein, “Heat Transfer and Friction in Tubes with Repeated-Rib Roughness,” International Journal of Heat and Mass Transfer, Vol. 14, No. 4,pp. 601-617, 1971.
6. M. J. Lewis, “An Elementary Analysis for Predicting the Momentum and Heat Transfer Characteristics of a Hydraulically Rough Surface,” ASME Journal of Heat Transfer, Vol. 97, No. 2, pp. 249-267, 1975.
7. A. E. Bergles, “Recent Development in Convective Heat-Transfer Augmentation,” Applied Mechanics Reviews, vol.26, pp.675-682, 1973.
8. A. E. Bergles, “Survey And Evaluation of Techniques to Augment Convective Heat and Mass Transfer,” Heat and Mass Transfer, vol.1, pp.331-424, 1969.
9. A. E. Bergles and R. L. Webb, “A Guide to the Literature on Convective Heat Transfer Augmentation,” Advances in Enhanced Heat Transfer-1985, S. M. Shenkman, J. E. O’Brien, I. S. Habib, and J. A. Kohler, Vol. HTD-Vol.43, pp.81-90, ASME Symposium, 1985.
10. J. C. Han, “Heat Transfer and Friction in Channels with Two Opposite Rib-Roughed Walls,” ASME Journal of Heat Transfer, Vol. 106, pp. 774-781, 1984.
11. Y. Park, J. Cha, and M. Kim, “Heat Transfer Augementation Characteristics of Various Inserts in a Heat Exchanger Tube,” Journal of Enhanced Heat Transfer, Vol.7,pp.23-33,2000.
12. S. W. Chang and L. M. Su, “Influence of Reciprocating Motion on Heat Transfer Inside a Ribbed Duct with Application to Piston Cooling in Marine Diesel Engines,” Journal of Ship Research, Vol. 41, No. 4, pp. 332-339,1997.
13. S. W. Chang, L. M. Su, W. D. Morris, and T. M. Liou, “Heat Transfer in a Smooth-Walled Reciprocating Anti-Gravity Open Thermosyphon,” International Journal of Heat and Mass Transfer, Vol. 42, pp. 1089-1103, 2003.
14. Wu-Shung Fu, Wen-Wang Ke, Ke-Nan Wang, “Laminar Forced Convection in a Channel With a Moving Block,” International Journal of Heat and Mass Transfer Vol. 44(13), pp.2385-2394, 2001.
15. 賴昱志，”增進活塞熱傳效益之數值模擬”， 國立交通大學機械工程研究所碩士論文，2004。
16. 連信宏，”利用多孔性介質增強活塞頂面之熱傳效率”， 國立交通大學機械工程學系碩士論文，2005。

17. 劉維元，”多孔性介質的熱傳分析”， 國立交通大學機械工程研究所碩士論文，1994。
18. 黃新鉗，”加裝多孔凸塊以增強熱傳效率之研究”， 國立交通大學機械工程研究所博士論文，1997。
19. 余政倫，”往復式冷卻渠道之熱流實驗”， 國立交通大學機械工程學系碩士論文，2006。
20. 陳沅佑，”實驗探討ㄇ型振動管之熱傳現象”， 國立交通大學機械工程學系碩士論文，2007。