跳到主要內容

臺灣博碩士論文加值系統

(216.73.217.114) 您好!臺灣時間:2026/11/17 07:22
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

我願授權國圖
: 
twitterline
研究生:楊忠憲
研究生(外文):Yang Chung-Hsien
論文名稱:應用微機電系統技術研製高性能壓阻式壓力與剪應力感測器
論文名稱(外文):The Study and Fabrication of Advanced Piezoresistive Pressure and Shear-Stress Sensors by Micro-Electro-Mechanical System(MEMS) Technologies
指導教授:方炎坤方炎坤引用關係、朱銘祥朱銘祥引用關係
指導教授(外文):Fang Yean-Kuen、Ju Ming-Shaung
學位類別:碩士
校院名稱:國立成功大學
系所名稱:電機工程學系
學門:工程學門
學類:電資工程學類
論文種類:學術論文
論文出版年:2000
畢業學年度:88
語文別:中文
論文頁數:95
中文關鍵詞:壓力、剪應力、有限元素法、平膜、凸緣、微機電系統、感測器、壓阻
外文關鍵詞:pressure、shear stress、finite element method、diaphragm、flange、MEMS、sensor、piezoresistive
相關次數:
  • 被引用被引用:1
  • 點閱點閱:428
  • 評分評分:
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:0
在論文中,吾人以單晶矽材料為主體,採用具有四端點、對剪應力靈敏之壓阻應變規(X-ducer)來取代傳統之惠斯頓橋式壓阻結構;描述應用微機電系統技術(MEMS)且配合有限元素法(Finite Element Method, FEM)分析結果來完成設計、製造及測試具有X型壓阻感測元素之微型壓力及剪應力感測器。
其中,壓力感測器經由單晶矽非等向性之KOH溶液濕蝕刻後,所得的感應平膜(Diaphragm)尺寸為3000X3000X100 um3,並將X型壓阻佈植在方形平膜邊界中點且與邊緣成45°處,以得最大之壓力靈敏度。由量測結果可知,在640Kpa的壓力範圍內,元件之靈敏度為7 uv/mA-Kpa且其壓力磁滯誤差小於6.4 %FS(full scale)。
而本實驗所研製之剪應力感測器的平膜尺寸為3000X3000X300 um3;藉由所沈積之二氧化矽薄膜的面型微機械加工(surface micromachining),可得方形凸緣(Flange)尺寸為1100X1100X3 um3。並將X型壓阻佈植在邊界中點與方形平膜中心之間,使其受正向壓力影響較小,而有較大之剪應力靈敏度。 在70Kpa的剪應力範圍內,元件量測所得之靈敏度為3.6 uv/mA-Kpa且其剪應力磁滯誤差小於8.9 %FS。
Based on computer finite element analysis ANSYS5.3 and micro-electro-mechanical system(MEMS) technologies, monolithic silicon micro pressure and shear-stress sensors have been designed and fabricated. The sensors employ one or two four-terminal shear-stress sensitive piezoresistive transverse voltage strain gauge in place of the conventional Wheatstone bridge construction.
In the developed pressure sensor, a square diaphragm with 3000X3000X100 um3 is formed by bulk micromachining of an n-type <100> monolithic silicon in KOH solution. The gauge, which is called an X-ducer, was implanted with Boron ions on the midpoint of the diaphragm edge at an incline angle 45°in order to maximize pressure sensitivity. Silicon pressure sensors fabricated using this X-ducer technology yield sensitivity of 7 uv/mA-Kpa for a 640Kpa full scale pressure range with pressure hysteresis errors of less than 6.4 %FS.
In the micro shear-stress sensor, a 3000X3000X300 um3 diaphragm is also prepared by anisotropic wet etching of bulk silicon in KOH solution and a square flange with 1100X1100X3 um3 above the sensing diaphragm is formed through surface micromachining of deposited SiO2 thin film. With ion implantation, two X-ducers were placed at the closely middle points between mid-edge points and center of the diaphragm where less sensitivity to normal pressure and higher sensitivity to shear-stress. The sensitivity of 3.6 uv/mA-Kpa for a 70Kpa full scale shear-stress range with shear-stress hysteresis errors of less than 8.9 %FS has been measured in the developed shear-stress sensor.
中文摘要
英文摘要
圖表目錄
第一章 前言 ………………………………………………………………1
第二章 成長系統及元件主要製程…………………………………………5
2-1 二氧化矽及氮化矽薄膜之成長系統與製程………………………5
2-1-1 濺鍍成長原理…………………………………………………5
2-1-2 二氧化矽及氮化矽薄膜之成長系統……………………7
2-1-3 二氧化矽及氮化矽薄膜之製程…………………………7
2-2 單晶矽非等向性蝕刻………………………………………………9
2-3 電化學放電玻璃鑽孔加工…………………………………………10
2-4 陽極接合技術………………………………………………………11
第三章 X-ducer 壓阻感測元素……………………………………………13
3-1 壓阻效應……………………………………………………………13
3-2 X-ducer與電橋式壓阻之比較……………………………………13
3-3 X-ducer 壓阻之工作原理…………………………………………14
3-4 X-ducer壓阻特性之影響因素……………………………………17
第四章 壓力感測器…………………………………………………………19
4-1 靈敏度、靈敏度溫度係數及偏差溫度係數之定義………………19
4-2 X-ducer壓力感測器之設計………………………………………20
4-2-1 元件結構………………………………………………………20
4-2-2 設計之考量……………………………………………………20
4-2-3 設計之步驟……………………………………………………21
4-3 X-ducer壓力感測器之製程………………………………………25
第五章 剪應力感測器………………………………………………………28
5-1 為何需要剪應力感測器……………………………………………28
5-2 剪應力感測器之設計………………………………………………28
5-2-1 元件結構………………………………………………………28
5-2-2 設計之考量……………………………………………………29
5-2-3 設計之步驟……………………………………………………29
5-3 剪應力感測器之製程………………………………………………31
第六章 元件量測系統及測試結果討論…………………………………34
6-1 元件量測系統………………………………………………………34
6-1-1 量測系統……………………………………………………34
6-1-2 定電流源之採用……………………………………………34
6-1-3 RC低通濾波電路之採用……………………………………35
6-2 壓力感測器之測試結果與討論……………………………………35
6-3 剪應力感測器之測試結果與討論…………………………………36
第七章 結論及建議………………………………………………………39
7-1 結論…………………………………………………………………39
7-2 建議…………………………………………………………………40
參考文獻
附表
附圖
誌謝及自述
[1]M. Zhang, et al, “Frictional action at lower limb/prosthetic socket interface,” Med. Eng. Phy., vol. 18, no. 3, pp. 207-214, 1996.
[2]M. Zhang, Arthur F. T. Mak, “A finite element analysis of the load transfer between an above-knee residual limb and its prosthetic socket-roles of interface friction and distal-end boundary conditions,” IEEE Transactions on Rehab. Eng., vol. 4, no. 4, pp. 337-346, 1996.
[3]D. J. Winarski & J. R. Pearson, ”First-Order Model for the Analysis of Stump Stresses for Below-Knee Amputees,” Tran. ASME, J. of Biomech. Eng., vol. 112, pp. 475-478, 1990.
[4]D. J. Winarski & J. R. Pearson, “Least-Squares Matrix Correlations Between Stump Stresses and Prosthesis Loads for Below-Knee Amputees,” ASME Journal of Biomechanical Engineering, Vol. 109, pp. 238-246, August 1987.
[5]W. Gopel, J. Hesse and J.N. Zemel, in H.H. Bau, N.F. de Rooij and B. Kloek (eds), “Sensors a Comprehensive Survey,” Vol. 7, Mechanical Sensors, VCH, Weinheim and New York, pp.146-172, 1994.
[6]Robert G. Seippel, “Transducers, Sensors, and Detectors”, Chapter 3, Reston Pub., Aprentice-Hall, Inc., 1980.
[7]S.K. Clark and K.D. Wise, “Pressure sensitivity in anisotropically etched thin diaphragm pressure sensors”, IEEE Trans. Electron Devices”, Vol. Ed-26, No 12, pp.1887-1896, 1979.
[8]J.E. Gragg, W.E. McCulley, W.B. Newton and C.E. Derrington, “Compensation and Calibration of a Monolithic four Terminals Silicon Pressure Transducers”, Tech Digest IEEE Solid-state sensor Workshop, Hilton Head Island, SC, USA, pp.21-27, 1984.
[9]S.M. Sze, Physics of Semiconductor Devices, 2nd Edition, John Wiley & Sons, pp. 30-35, 1981.
[10]Chang Liu, et al, “A micromachined flow shear-stress sensor based on thermal transfer principles,” J. of MEMS, vol. 8, no. 1, pp. 90-99, 1999.
[11]Tao Pan, et al, “Microfabricated shear stress sensors, part1: design and fabrication,” AIAA Journal, vol. 37, no. 1, pp. 66-72, 1999.
[12]D. Roche, et al, “Piezoelectric bimorph bending sensor for shear-stress measurement in fluid flow,” Sensors and Actuators A, vol. 55, pp. 157-162, 1996.
[13]Javad Shajii, et al, “A Micromachined floating-element shear stress sensor using wafer-bonding technology,” J. of MEMS, vol. 1, no. 2, pp. 89-94, 1992.
[14]A. Padmanabhan, et al, “Micromachined sensors for static and dynamic shear-stress measurement in aerodynamic flows,” Transducers’ 97, pp. 137-140, 1997.
[15]H. Seidel, L. Csepregi, A. Heuberger and H. Baumgartel, “Anisotropic Etching of Crystalline Silicon in Alkaline Solutions,” J. Electrochem. Soc., vol. 137, no. 11, November 1990.
[16]H. Seidel, “The Mechanism of Anisotropic Silicon Etching and its Relevance for Micromachining,” Digest of Tech. Papers, Transducers’ 87, 4th Intl. Conf. Solid-State Sensors and Actuators, pp. 120-125, 1987.
[17]O. Tabata, R. Asahi, H. Funabashi, K. Shimaoka and S. Sugiyama, “Anisotropic Etching of Silicon in TMAH Solutions,” Sensors and Actuators A, 34, pp.51-57, 1992.
[18]S. C. Kim, K. D. Wise, “Temperature sensitivity in silicon piezoresistive pressure transducers,” IEEE Trans. Electron Devices, vol. Ed-30, July, pp. 802-810, 1983.
[19]K. B. Albaugh, “Mechanism of anodic bonding of silicon to glass,” Proc. IEEE Solid State Sensors and Actuators Workshop, USA, 109, 1988.
[20]S. M. Sze, Semiconductor Sensors, Wiley & Sons, INC., New York, pp. 160-200, 1994.
[21]G. S. Chen, Design of Monolithic-Silicon Micro-Pressure Sensors, M.S. Thesis(in Chinese), Dept. of Mechanical Eng., National Cheng Kung University, May 1998.
[22]Timoshenko, S. and Woinowsky-Krieger, S., “Theory of Plates and Shells,” 2nd edition, McGraw-Hill Book Company, New York, 1959.
[23]Kurt E. Petersen, “Silicon as a Mechanical Material,” Proc. IEEE, vol. 70, no. 5, pp. 420-457, May 1982.
[24]F. P. Beer and E. R. Johnson, Mechanics of Materials, 2nd ed., McGraw-Hill, pp. 353-366.
[25]C. R. Huang, Design and Fabrication of Micro-electro-mechanical System Pressure Sensor for Rehabilitation Applications, M.S. Thesis(in Chinese), Dept. of Electrical Eng., National Cheng Kung University, June 1998.
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top
1. 林宗耀(1997) "x灣M2貨幣需求之探討 - 兼論制度性因素的影響", 中央銀行季刊: 19:1 頁 40-70
2. 沈中華, 陳華倫(1996), "f幣政策指標的建立與貨幣政策反應函數", 經濟論文24:4 頁 559-589
3. 齊珍慈(1995)‧親子依附關係建立過程及其護理‧榮總護理,12 (4),264-269。
4. 邱正雄, 侯德潛(1994) "價,貨幣政策指標與貨幣供給 - 台灣經驗", 中央銀行季刊: 17:2 頁 23-41
5. 廖珍娟(1988)‧早期親子依戀情感之增進‧護理雜誌,35 (2),23-30。
6. 楊雅玲、余玉眉(1990)‧剖腹產後經產婦對自己及新生兒之關注行為‧護理研究,1 (4),316-328。
7. 陳一端, 詹燈連(1997), "M2貨幣承數變動分析", 中央銀行季刊: 19:2 頁 30-45
8. 馮容莊(1994)‧中國母親的新生兒概念與哺餵互動行為之相關性探討‧護理研究,2 (2),116-129。
9. 曾雅玲、王麗玲、施幼玲(1993)‧準爸爸於生產過程的行為反應及護理需求之初步探討‧護理研究,1 (3),279-289。
10. 王舒芸、余漢儀(1997).奶爸難為-雙薪家庭之父職角色初探‧婦女與兩性學刊,8,115-149。
11. 王舒芸(1997).父親角色-養家者?照顧者?‧婦女與兩性研究通訊,41,23-28。
12. 李榮謙(1988) "璈鬘帠q貨之估計 - 兼論大家樂對通貨需求的影響", 中央銀行季刊: 10:1 頁 47-53
13. 彭淮南, 李榮謙(1987), "大家樂對社會大眾持有通貨的影響", 中央銀行季刊: 9:3 頁 14-21
14. 張炳耀(1991), "H淨超額準備作為操作目標之評估", 中央銀行季刊: 13:2 頁 42-52
15. 許嘉棟(1996), "x灣的民間借貸", 基層金融: 32期 頁1-19