臺灣博碩士論文加值系統

本文以直接模擬蒙地卡羅法(Direct Simulation Monte Carlo Method)[1]來模擬改變不同進出口壓力之二維背向式階梯微流場，用以分析不同紐森數對流場現象之影響，接著探討三維背向式階梯微流場的流場現象。本文使用質量流率相等法來修正低速背向式階梯微流場的進出口邊界條件，所模擬的工作流體為氮氣(N2)，分子模型則採用VHS分子模型。
在本文中，由不同紐森數之二維模擬結果，可以發現當流場kn=0.1時渦流現象將消失，而由流場圖中則是發現當kn值越大，也就是流場越稀薄的時候，階梯的影響將不顯著，由於流場稀薄度變大的關係導致流場內的速度梯度變大，發現流場有發散的跡象。而在三維的模擬中，三維之模擬結果與二維之模擬結果有明顯的差異；就速度分佈來看，三維流場之模擬結果比二維流場之模擬結果低了許多，大約只有二維模擬的70％，這是因為三維模擬流場之管壁效應比二維模擬流場大的結果；也由於這個原因，三維流場模擬結果中，渦流消失的流場之kn值與二維流場是不同的，三維模擬時當流場kn=0.02渦流消失。本文也模擬加大寬高比1，3和5倍，其結果顯現在三維的模擬時，寬高比小於3的時候，兩邊壁的效應對流場的影響就相當顯著，隨著寬高比的增加，此時流場性質愈趨近二維模擬時的結果，所以本文發現當管徑之寬高比大於5時，以二維流場模擬三維實例是合理的。

The Direct Simulation Monte Carlo (DSMC) method has been employed to analyze the rationality of the 2-D simplification for a 3-D backward-facing step flow. An mass flux treatment for low-speed inflow and outflow boundaries for the DSMC of the microchannel flow is employed. The VHS model and Nitrogen was employed in the simulation. The 3-D microchannel flows is simulated with the cross aspect ratio in the range of 1 and 5. The calculated flow properties in the 3-D cases are compared with the results of the 2-D case. It shows that when the aspect ratio < 3, the two extra side walls in the 3-D case have significant effects on the heat transfer and flow properties. When the aspect ratio increases, the flow pattern and heat transfer characteristics tend to approach that of 2-D results. The 2-D simplification is found to be reasonable only when the cross aspect ratio is larger than 5.
In this paper, the effects of rarefaction on flow characteristics are also analyzed and discussed. It is found that flow separation, recirculation, and reattachment will disappear as Knudsen number, Kn, exceeds 0.1 for 2-D case, and will disappear as Kn exceeds 0.02 for 3-D case.

目錄

目錄 I
表目錄 III
圖目錄 IV
符號說明 VI
第一章 緒 論 1
1-1 前言 1
1-2 文獻回顧 4
1-3 研究目的與方法 7
第二章 直接模擬蒙地卡羅法 10
2-1 DSMC 法 10
2-2網格設置與計算時步 11
2-3流場初始條件 12
2-4流場邊界處理 13
2-5低速流之進出口條件設定方法 16
2-6碰撞對(Collision Pair)的選擇 17
第三章 分子模型的選擇 20
3-1 硬球模型(HS) 20
3-2 可變硬球模型(VHS) 20
3-3 可變軟球模型(VSS) 21
3-4 雙原子分子模型 22
第四章 結果與討論 26
4-1 模擬模型 26
4-2 二維模擬結果 26
4-3 不同紐森數區間對二維背向式階梯微流場之影響 27
4-4 三維模擬與二維模擬驗證與比較 28
4-5 不同紐森數區間對三維背向式階梯微流場之影響 29
第五章 結論與未來工作 31
5-1 結論 31
5-2 未來工作 32
參考文獻 33

表目錄

表 4-1 VHS 分子模型基本參數 36
表 4-2 二維背向式階梯微流場基本設定 36
表 4-3 二維矩形方管流場基本設定 37
表 4-4 改變三維矩形管口徑之流場設定 37

圖目錄
圖1-1 Kn值與統御方程式間的關係圖 38
圖2-1 DSMC流程圖 38
圖2-2分子碰撞面積示意圖 39
圖3-1硬球模型碰撞示意圖 39
圖4-1 Hong Xue與Bin Xu二維背向式階梯微流場模型示意圖 40
圖4-2 三維背向式階梯微流場模型示意圖 40
圖4-3 Hong Xue二維微流場模型示意圖 41
圖4-4 二維背向式階梯微流場驗證圖 42
圖4-5 二維矩形空管流場驗證圖 43
圖4-6 二維不同kn值之流線速度圖 45
圖4-7 二維不同kn值之流場速度圖 47
圖4-8 三維不同管徑寬度與二維模擬之速度比較圖 49
圖4-9 三維不同管徑寬度與二維模擬之壓力分佈比較圖 51
圖4-10 三維kn=0.04之流線速度圖 52
圖4-11 三維kn=0.04之流場速度圖 52
圖4-12 三維kn=0.03之流線速度圖 53
圖4-13 三維kn=0.03之流場速度圖 53
圖4-14 三維kn=0.02之流線速度圖 54
圖4-15 三維kn=0.02之流場速度圖 54
圖4-16 三維kn=0.01之流線速度圖 55
圖4-17 三維kn=0.01之流場速度圖 55

[1]Mohamed Gad-el-Hak, The MEMS Handbook, CRC Press, 2002.
[2]Bird, G. A. “Molecular Gas Dynamics And The Direct Simulation of Gas Flows,” Oxford University Press, 1994.
[3]Bird, G. A., “Approach to Translational Equilibrium in a Rigid Sphere Gas,” Phys. Fluids Vol. 6, pp. 1518-1519, 1963.
[4]Bird, G. A., “The Velocity Distribution Function Within a Shock Wave,” Journal of Fluid Mechanics, Vol. 30, part 3, pp. 479-487, 1967.
[5]Borgnakke, C., and Larsen, P. S., “Statistical Collision Model for Monte Carlo Simulation of Polyatomic Gas Mixture,” Journal of Computational Physics, Vol. 18, No. 4, pp. 405-420, 1975.
[6]Bird, G. A., “Molecular Gas Dynamics,” Oxford, UK:Clarenden, 1976
[7] Bird, G. A., “Perception of Numerical Method in Rarefied Gas Dynamics,” in Rarefied Gas Dynamics:Theoretical and Computational Techniques, Vol. 118 of Progress in Aeromautics and Astronautics, AIAA, Washington, DC, 1989.
[8]Muntz, E. P., “Rarefied gas dynamics,” Annu. Rev. Fluid Mech. 21, pp. 387-417, 1989.
[9]Cheng, H. K., “Perspectives on hypersonic viscous flow research,” Annu. Rev. Fluid Mech. 25, pp. 455–484, 1993.
[10]Cheng, H. K., and Emmanuel, G., “Perspectives on hypersonic nonequilibrium flow,” AIAA J. 33, pp. 385–400, 1995.
[11] Bird, G. A., “Recent Advance and Current Challenges for DSMC,” Comput. Math. Appl., Vol. 35, pp. 1-14, 1998.
[12]Beskok, A., and Karniadakis, D. E., “Modeling Separation in Rarefied Gas Flows,” 28th AIAA Shear Flow Control Conference, Snowmass Village, CO, 1997.
[13]Arkilic, E. B., Breuer, K. S., and Schmidt, M. A., “Gaseous Flow in Micro-channels,” Application of Microabrication to Fluid Mechanics, ASME, FED-Vol. 197, pp. 57-66, 1994.
[14]Piekos, E. S., and Breuer, K. S., “Numerical Modeling of Micromechanical Devices Using the Direct Simulation Monte Carlo Method,” Journal of Fluids Engineering, Vol. 118, pp. 464-469, 1996.
[15]Nance, R. P., Hash, D. B., and Hassan, H. A., “Role of Boundary Conditions in Monte Carlo Simulation of Microelectromechanical Systems,” Journal of Thermophysics and Heat Transfer, Vol. 12, No. 3, pp. 447-449, 1998.
[16]Liou, W. W., and Fang, Yichuan, “Implicit Boundary Conditions for Direct Simulation Monte Carlo Method in MEMS Flow Predictions,” CMES, Vol. 1, No. 4, pp. 119-128, 2000.
[17]Liou, W. W., and Fang, Yichuan, “Computation of the Flow and Heat Transfer in Microdevices Using DSMC With Implicit Boundary Conditions,” Journal of Heat Transfer, Vol. 124, pp.338-345, 2002.
[18] 羅文彬，“以直接模擬蒙地卡羅法模擬二維微管流場”，淡江大學機械與機電工程學系碩士班，台北，2004
[19] 潘建志，“流經靠近一平板的矩形柱體稀薄氣流的直接模擬蒙地卡羅法分析”，大同大學機械工程研究所，台北，2000。
[20] 林文榮，“利用DSMC方法分析微通道氣體流動特性與熱傳之研究”，國立雲林科技大學機械工程研究所，雲林，2000。
[21] Hong Xue, Shuhui Chen, “DSMC Simulation of Microscale Backward-facing Step Flow,” Microscale Thermophysical Engineering, Vol. 7, pp. 69-86, 2003
[22] 陳炳炫，“Knudsen區氣體微尺度流動之蒙地卡羅直接模擬”，國防大學中正理工學院國防科學研究所，桃園，2003。
[23] 蘇嘉南，“以三維蒙地卡羅法模擬分析高速微管流場”，國立成功大學航空太空工程研究所，台南，2000。
[24] 洪念慈，“以直接模擬蒙地卡羅法計算三維微管流場”，淡江大學機械與機電工程學系碩士班，台北，2004
[25] 邱昱中，“微結構三維流場及熱傳現象”，淡江大學機械與機電工程學系碩士班，台北，2005
[26] Hong Xue, Bin Xu, Yao Wei, and Jian Wu, “Unique Behaviors of A Backward-facing Step Flow at Microscale,” Numerical Heat Transfer, Part A, Vol. 47, pp. 251-268, 2005.
[27] Horn, A., Schroder, H., Obermeier, E., Wachutka, G., “Simulation of Orientation-Depebdent Etching of Silicon Using a New Step Flow Model of 3D Structuring,” 2005.
[28] Perez Guerrero, J. S. and Cotta, R. M., “Benchmark Intergral Transform Results for Flow Over a Backward-Facing Step,” Journal of Computers and Fluids, Vol. 25, No. 5, pp. 527-540, 1996.
[29] Valencia, A. and Hinojosa, L. “Numerical Solutions of Pulsating Flow and Heat Transfer Characteristics in a Channel with a Backward-Facing Step,” Journal of Heat and Mass Transfer, Vol. 32, pp. 143-148, 1997.
[30] Lee, T. and Mateescu, D., “Experimental and Numerical Investigation of 2-D Backward-Facing Step Flow,” Journal of Fluids and Structures, Vol. 12, pp. 703-716, 1998.
[31] Chiang, T. P., Sheu, T. H. and Fanf, C. C., “Numerical Investigation of Vortical Evolution in a Backward-Facing Step Expansion Flow,” Applied Mathematical Modeling, Vol. 23, pp. 915-932, 1999
[32] Abu-Mulaweh, H. I., “Effects of Backward-and Forward-Facing Steps on Turbulent Natural Convection Flow Along a Vertical Plate,” International Journal of Thermal Sciences, Vol. 41, pp. 376-385, 2002.
[33] Hong Xue, Q. Fan,, C. Shu, “Prediction of Micro-channel Flows using Direct Simulation Monte Carlo,” Probabilistic Engineering Mechanics, Vol. 15, pp. 213-219, 2000.