跳到主要內容

臺灣博碩士論文加值系統

(216.73.217.68) 您好!臺灣時間:2026/11/21 09:11
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

我願授權國圖
: 
twitterline
研究生:廖健嵐
研究生(外文):Liao, Chien Lan
論文名稱:高頻調變氮化物藍綠發光二極體之研製與分析
論文名稱(外文):The Development of GaN-Based High-Speed Blue/Green Light Emitting Diodes
指導教授:吳孟奇、何充隆
指導教授(外文):Wu, Meng Chyi、Ho, Chong Long
學位類別:博士
校院名稱:國立清華大學
系所名稱:電子工程研究所
學門:工程學門
學類:電資工程學類
論文種類:學術論文
論文出版年:2015
畢業學年度:103
語文別:英文
論文頁數:104
中文關鍵詞:高頻、發光二極體、氮化鎵
外文關鍵詞:High frequency、Light emitting diodes、GaN
相關次數:
  • 被引用被引用:0
  • 點閱點閱:243
  • 評分評分:
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:1
在本論文中,我們設計與製作了高速氮化物發光二極體,近年來因發光二極體具低功耗、壽命長等優點,其研發導向皆朝向照明及背光應用為主,並已逐漸取代傳統光源做為照明的器具;但這僅是發光二極體的優點之一,我們利用發光二極體本身高頻調變的特性,設計適當的圖案及製程步驟來製作高速(高頻)的元件。
本論文中,我們呈現了藍光與綠光發光二極體於不同發光孔徑下所對應的高頻特性,然為了得到較高的頻寬,必須注入較大的電流密度,因此我們設計了環狀金屬電極來侷限電流注入的地方,並透過適當的圖案設計與原子層沉積系統所成長的氧化鎵鋅透明導電膜(此透明導電膜擁有較低的電阻率),並搭配P型氮化鎵層本身較高的橫向電阻值,使電流可以達到自我向下侷限的目的;另外,因擁有較高的電流密度可有效減少載子複合生命週期,因考慮到RC時間常數,故將焊接墊的尺寸縮小為80~100 μm,可有效降低焊接墊所導致之電容值。
本論文中,我們研究著重的波段主要落在藍光(450 nm)及綠光(500 nm),在注入電流35 mA的情況下藍光發光二極體可達到225 MHz及1.6 mW;綠光發光二極體在50 mA的操作電流下,可達到463 MHz及1.6 mW,主動區尺寸皆為75 μm的直徑。
另外,我們也針對高頻發光二極體於不同操作溫度下,特性上所對應的變化:順向偏壓、逆向飽和電流、發光頻譜、光強度、接面溫度及頻寬,做了一詳細之研究。並與德國Polymer Optical Fiber Application Center合作,將此試片應用至塑膠光纖系統中,得到在傳輸距離一公尺時,傳輸速率可達4.8 Gb/s 及 4.3 Gb/s,分別在4-PAM及NRZ的測量條件下。

In this dissertation, we have demonstrated GaN-based high-speed Light-emitting diodes (LEDs). In recently, LEDs is one of the most important light sources due to its low power consumption and long lifetime. We use its natural feature to get a high modulation bandwidth. We present the high-frequency characteristics of GaN-based blue and green LEDs with different aperture diameters. In order to get higher current density, we use ring-shaped electrode to confine the current injection. Through appropriate device design, gallium-doped Zinc oxide film deposited by atomic layer deposition is used as the top contact layer with high lateral resistance to self-confine the current injection. In addition, a smaller bonding pad is used to reduce the RC time constant. The LEDs investigated have a peak emission wavelength of 450 and 500 nm. The high optical 3-dB modulation bandwidth are 225 MHz at 35 mA for the blue LEDs and 463 MHz at 50 mA for the green LEDs with an aperture diameter of 75 µm. The LED also exhibits a relatively high output power of 1.6 mW at 35 mA for the blue LEDs and 1.6 mW at 50 mW for the green LEDs. We also present the device performance of high-speed GaN-based green LEDs at different operating temperatures. Temperature dependence of the characteristics of forward voltage, reverse leakage current, electroluminescence linewidth and peak wavelength, light output power, junction temperature, and 3-dB bandwidth are investigated in details. In addition, we work with the Polymer Optical Fiber Application Center in Germany. A maximum bit rate of 4.81 Gb/s and 4.34 Gb/s was achieved over a 1-m SI-POF employing 4-pulse-amplitude (4-PAM) and None-Return-to-Zero (NRZ) modulation format, respectively. Such the LEDs can be applied to plastic optical fiber (POF) and visible light communication (VLC) in the future.
中 文 摘 要............................................I
Abstract...............................................III
誌 謝..................................................V
Contents...............................................VII
List of Figure.........................................IX
Chapter 1. Introduction................................1
1-1 Overview of light-emitting diodes..................1
1-2 Research motivation................................3
Chapter 2. The Basis of Theory and Characterization Instruments............................................8
2-1 Basic theory of high-speed light emitting diode....8
2-2 Growth mechanism of atomic layer deposition........15
2-3 Characterization instruments.......................16
2-3-1 Current-Voltage (I-V) and Capacitance-Voltage (C-V) Characteristic Measurement Systems.....................16
2-3-2 Electroluminescence Spectrum (EL) measurement system.................................................17
2-3-3 Luminous Intensity (L-I) Characteristic Measurement Systems................................................18
2-3-4 Divergence angle measurement system..............20
2-3-5 Modulation bandwidth measurement system..........20
2-3-6 Near-Field light intensity measurement system....21
Chapter 3. LEDs Device Structure and Fabrication.......31
3-1 Epitaxial structure design concept.................31
3-2 The design of Mask.................................32
3-3 Experiment process of GaN-based high-speed LEDs....34
Step 1. n-GaN mesa etching.............................34
Step 2. n-metal contact layer deposition...............36
Step 3. Dielectric deposition..........................36
Step 4. p-metal contact layer deposition...............37
Step 5. ALD-GZO deposition.............................38
Step 6. Lapping and polishing..........................39
Step 7. Dicing and bonding.............................40
Chapter 4. Characteristics of High-Speed LEDs..........51
4-1 ALD-GZO film characteristics.......................51
4-2 Devices characteristics measurement................52
4-3 The blue LEDs characteristics analysis.............52
4-3-1 I-V and C-V characteristics analysis.............53
4-3-2 EL characteristics analysis......................54
4-3-3 Frequency response (f3dB) and L-I characteristics analysis...............................................54
4-4 The green LEDs characteristics analysis............56
4-4-1 I-V and C-V characteristics analysis.............56
4-4-2 EL characteristics analysis......................57
4-4-3 Frequency response (f3dB) and L-I characteristics analysis...............................................57
4-4-4 Near-Field light intensity and Divergence angle characteristics analysis...............................59
4-5 Temperature dependence characteristics analysis....60
4-5-1 I-V characteristics analysis.....................61
4-5-2 EL characteristics analysis......................62
4-5-3 Frequency response and junction temperature characteristics analysis...............................64
4-6 Data transmission characteristics analysis.........68
4-7 Micro-LEDs : Design, Fabrication, Result and Discussion.............................................69
Chapter 5. Conclusions and Future Work.................91
References.............................................93
Published list.........................................100
[1]
C. T. Lee, and C. Y. Chuang, “Light extraction enhancement of GaN-based flip-chip light-emitting diodes using diffused nanorod reflector,” Appl. Phys. Exp., vol. 5, no. 11, pp. 112104–12104-3, Oct. 2012.
[2]
L. W. Jang, J. W. Ju, D. W. Jeon, J. W. Park, A. Y. Polyakov, S. J. Lee, J. H. Baek, S. M. Lee, Y. H. Cho, and I. H. Lee, “Enhanced light output of InGaN/GaN blue light emitting diodes with Ag nano-particles embedded in nano-needle layer,” Opt. Exp., vol. 20, no. 6, pp. 6036–6041, Mar. 2012.
[3]
A. J. Shaw, A. L. Bradley, J. F. Donegan, and J. G. Lunney, “GaN resonant cavity light-emitting diodes for plastic optical fiber applications,” IEEE Photon. Technol. Lett., vol. 16, no. 9, pp. 2006–2008, Sep. 2004.
[4]
J. J. D. McKendry, R. P. Green, A. E. Kelly, Z. Gong, B. Guilhabert, D. Massoubre, E. Gu, and M. D. Dawson, “High-speed visible light communications using individual pixels in a micro light-emitting diode array,” IEEE Photon. Technol. Lett., vol. 22, no. 18, pp. 1346–1348, Sep. 2010.
[5]
IEEE Standard for Local and Metropolitan Area Networks-Part 15.7: Short-Range Wireless Optical Communication Using Visible Light, IEEE Standard 802.15.7, 2011.
[6]
M. Meier, S. Karg, and W. Riess, “Light-emitting diodes based on poly-p-phenylene-vinylene: II. Impedance spectroscopy,” Appl. Phys. Lett., vol. 82, no. 4, pp. 1961–1966, May 2007.
[7]
W. S. Wong, T. Sands, N. W. Cheung, M. Kneissl, D. P. Bour, P. Mei, L. T. Romano, and N. M. Johnson, “Fabrication of thin-film InGaN light-emitting diode membranes by laser lift-off,” Appl. Phys. Lett., vol. 75, no. 10, pp. 1360–1362, Sep. 1999.
[8]
J. K. Sheu, M. L. Lee, Y. S. Lu, and K. W. Shu, “Ga-doped ZnO transparent conductive oxide films applied to GaN-based light-emitting diodes for improving light extraction efficiency,” IEEE J. Quantum Electron., vol. 44, no. 12, pp. 1211–1218, Dec. 2008.
[9]
J. W. Shi, J. K. Sheu, C. H. Chen, G. R. Lin, and W. C. Lai, “High-speed GaN-based green light-emitting diodes with partially n-doped active layers and current-confined apertures,” IEEE Electron Device Lett., vol. 29, no. 2, pp. 158–160, Feb. 2009.
[10]
J. W. Shi, H. Y. Huang, J. K. Sheu, C. H. Chen, Y. S. Wu, and W. C. Lai, “The improvement in modulation speed of GaN-based green light-emitting diode (LED) by use of n-type barrier doping for plastic optical fiber (POF) communication,” IEEE Photon. Technol. Lett., vol. 18, no. 15, pp. 1636–1638, Aug. 1, 2006.
[11]
T. Matsuoka, T. Ito, and T. Kaino, “First plastic optical fibre transmission experiment using 520 nm LEDs with intensity modulation/direct detection,” Electron Lett., vol. 36, no. 22, pp. 1836–1837, Oct. 2000.
[12]
E. F. Schubert, Light-Emitting Diodes. Cambridge, U.K.: Cambridge Univ. Press, 2006.
[13]
H. L. Minh, D. O’Brien, G. Faulkner, L. Zeng, K. Lee, D. Jung, Y. Oh, and E. T. Won, “100-Mb/s NRZ visible light communications using a postequalized white LED,” IEEE Photon. Technol. Lett., vol. 21, no. 15, pp. 1063–1065, Aug. 1, 2009.
[14]
J. J. D. McKendry, D. Massoubre, S. Zhang, B. R. Rae, R. P. Green, E. Gu, R. K. Henderson, A. E. Kelly, and M. D. Dawson, “Visible-light communications using a CMOS-controlled micro-light-emitting-diode array,” J. Lightw. Technol., vol. 30, no. 1, pp. 61–67, Jan. 1, 2012.
[15]
S. H. Tu, C. J. Lan, S. H. Wang, M. L. Lee, K. H. Chang, R. M. Lin, J. Y. Chang, and J. K. Sheu, “InGaN gallium nitride light-emitting diodes with reflective electrode pads and textured gallium-doped ZnO contact layer,” Appl. Phys. Lett., vol. 96, no. 13, pp. 133504-1–133504-3, 2010.
[16]
K. Y. Yen, C. H. Chiu, C. W. Li, C. H. Chou, P. S. Lin, T. P. Chen, T. Y. Lin, and J. R. Gong, “Performance of InGaN/GaN MQW LEDs using Ga-doped ZnO TCLs prepared by ALD,” IEEE Photon. Technol. Lett., vol. 24, no. 23, pp. 2105–2108, Dec. 2012.
[17]
650 nm high-speed RCLED, Model No. RCLED-150, LUXNET Corporation.
[18]
InGaAlP Resonant Cavity LED-Chip (660nm, High Power), Model No. F0372A, OSRAM Opto Semiconductors.
[19]
High-Speed Resonant Cavity LED, Model No. FC300R-120, Firecomms Ltd.
[20]
http://www2.warwick.ac.uk/fac/sci/physics/current/postgraduate/regs/mpags/ex5/intro/
[21]
http://www.ieee802.org/15/pub/TG7.html
[22]
http://www.taringa.net/posts/ciencia-educacion/18139014/Li-Fi-La-nueva-conexion-a-internet-pronto-en-Chile.html
[23]
R. Hou1, Y. Chen, J. Wu, and H. Zhang, “A Brief Survey of Optical Wireless Communication,” AusPDC 2015, Sydney, Australia, pp. 41–50, Jan. 2015.
[24]
P. Bhattacharya, Semiconductor Optoelectronic Devices, 2nd ed. Upper Saddle River, NJ, USA: Prentice-Hall, 1997.
[25]
K. D. Choquette, R. P. Schneider, Jr., K. L. Lear, and K. M. Geib, “Low threshold voltage vertical-cavity lasers fabricated by selective oxidation,” Electron. Lett., vol. 30, no. 24, pp. 2043-2044, 1994.
[26]
M. Jalonen, M. Toivonen, J. Kongas, A. Salokatve, and M. Pessa, “Oxide-confined resonant cavity red light-emitting diode grown by solid source molecular beam epitaxy,” Electron. Lett., vol. 33, no. 23, pp. 1989-1990, 1997.
[27]
R. Wirth, C. Karnutsch, S. Kugler, and K. Streubel, “High-Efficiency Resonant-Cavity LEDs Emitting at 650 nm,” IEEE Photon. Technol. Lett., vol. 13, no. 5, pp. 421–423, May. 2001.
[28]
K. Y. Lau, and A. Yariv, “Ultra-High Speed Semiconductor Lasers,” IEEE J. Quantum Electron., vol. QE-21, no. 2, pp. 121–138, Feb. 1985.
[29]
M. Fukuda, Optical Semiconductor Device, Kanagawa, Japan: John Wiley & Sons, 1999.
[30]
G. Ghione, Semiconductor Devices for High-Speed Optoelectronics. Cambridge Univ. Press, 2009.
[31]
Y. Xi, and E. F. Schubert, “Junction–temperature measurement in GaN ultraviolet light-emitting diodes using diode forward voltage method,” Appl. Phys. Lett., vol. 85, no. 12, pp. 2163–2165, Sep. 2004.
[32]
S. C. Bera, R. V. Singh, and V. K. Garg, “Temperature behavior and compensation of light-emitting diode,” IEEE Photon. Technol. Lett., vol. 17, no. 11, pp. 2286–2288, Nov. 2005.
[33]
S. Chhajed, Y. Xi, Th. Gessmann, J. Q. Xi, J. M. Shah, J. K. Kim, and E. F. Schubert, “Junction temperature in light-emitting diodes assessed by different methods,” Proc. SPIE, vol. 5739, pp. 16–24, Mar. 2005.
[34]
B. H. Kim, and C. H. Moon, “Comparison of the thermal performance of the multichip LED packages,” IEEE Trans. Compon. Packag. Manuf. Technol., vol. 2, no. 11, pp. 1832–1837, Nov. 2012.
[35]
G. Weling, J. Xuejiao, Y. Fei, C. Bifeng, and G. Wei, “Characteristics of high power LEDs at high and low temperature,” J. Semicond., vol. 32, no. 4, pp. 044007-1–044007-3, Apr. 2011.
[36]
Y. J. Lee, C.-J. Lee, and C. H. Chen, “Determination of junction temperature in InGaN and AlGaInP light-emitting diodes,” IEEE J. Quantum Electron., vol. 46, no. 10, pp. 1450–1455, Oct. 2010.
[37]
Y. Gu, and N. Narendran, “A non-contact method for determining junction temperature of phosphor-converted,” Proc. SPIE, vol. 5187, pp. 64–75, Jan. 2004.
[38]
Y. J. Lee, C. J. Lee, and C. H. Chen, “Estimating the junction temperature of InGaN and AlGaInP light-emitting diodes,” Jpn. J. Appl. Phys., vol. 50, no. 4S, pp. 04DG18-1–04DG18-5, Apr. 2011.
[39]
B. H. Yu, and Y. H. Wang, “Junction temperature and thermal resistance restrict the developing of high-power LED,” Chinese J. Lumin., vol. 26, pp. 761–766, 2005.
[40]
H. K. Kim, K. J. Ahn, H. Jang, and H. Lee, “Dependence of Electrical, Optical, and Structural Properties on the Thickness of GZO Films Prepared by CRMS,” J. Electrochem. Soc., vol. 159, no. 1, pp. H38–H43, Dec. 2012.
[41]
W. T. Yen, Y. C. Lin, P. C. Yao, J. H. Ke, and Y. L. Chen, “Effect of post-annealing on the optoelectronic properties of ZnO:Ga films prepared by pulsed direct current magnetron sputtering,” Thin Solid Films, vol. 518, no. 14, pp. 3882–3885, Oct. 2010.
[42]
C. C. Chen, C. C. Tsao, Y. C. Lin, and C. Y. Hsu, “Optimization of the sputtering process parameters of GZO films using the Grey–Taguchi method,” Ceram. Int., vol. 36, no. 3, pp. 979-988, Nov. 2010.
[43]
G. Goncalves, E. Elangovan, P. Barquinha, L. Pereira, R. Martins, and E. Fortunato, “Influence of post-annealing temperature on the properties exhibited by ITO, IZO and GZO thin films,” Thin Solid Films, vol. 515, no. 24, pp. 8562-8566, Apr. 2007.
[44]
T. Takeuchi, C. Wetzel, S. Yamaguchi, H. Sakai, H. Amano, I. Akasaki, Y. Kaneko, S. Nakagawa, Y. Yamaoka, and N. Yamada, “Determination of piezoelectric fields in strained GaInN quantum wells using the quantum-confined Stark effect,” Appl. Phys. Lett., vol. 73, no. 12, pp. 1691–1693, Jul. 1998.
[45]
J. M. Shah, Y. L. Li, T. Gessmann, and E. F. Schubert, “Experimental analysis and theoretical model for anomalously high ideality factors (n2.0) in AlGaN/GaN p-n junction diodes,” J. Appl. Phys., vol. 94, no. 4, pp. 2627–2630, Aug. 2003.
[46]
C. L. Liao, C. L. Ho, Y. F. Chang, C. H. Wu, and M. C. Wu, “High-Speed Light-Emitting Diodes Emitting at 500 nm With 463-MHz Modulation Bandwidth,” IEEE Electron Device Lett., vol. 35, no. 5, pp. 563–565, May. 2014.
[47]
J. Hader, J. V. Moloney, and S. W. Koch, “Temperature dependence of radiative and Auger losses in quantum wells,” IEEE J. Quantum Electron., vol. 44, no. 2, pp. 185–191, Feb. 2008.
[48]
P. Tian1, J. J. D. McKendry1, J. Herrnsdorf1, S. Watson, R. Ferreira1, I. M. Watson1, E. Gu1, A. E. Kelly, and M. D. Dawson1, “Temperature-dependent efficiency droop of blue InGaN micro-light emitting diodes,” Appl. Phys. Lett., vol. 105, no. 17, pp. 171107-1–171107-5, Oct. 2014.
[49]
H. P. T. Nguyen, M. Djavid, K. Cui, and Z. Mi, “Temperature-dependent nonradiative recombination processes in GaN-based nanowire white-light-emitting diodes on silicon,” Nanotechnology, vol. 23, no. 19, pp. 194012-1–194012-6, Apr. 2012.
[50]
A. David, and M. J. Grundmann “Droop in InGaN light-emitting diodes: A differential carrier lifetime analysis,” Appl. Phys. Lett., vol. 96, no. 10, pp. 103504-1–103504-3, Mar. 2010.
[51]
R. P. Green, J. J. D. McKendry, D. Massoubre, E. Gu, M. D. Dawson, and A. E. Kelly, “Modulation bandwidth studies of recombination processes in blue and green InGaN quantum well micro-light-emitting diodes,” Appl. Phys. Lett., vol. 102, no. 9, pp. 091103-1–091103-4, Mar. 2013.
[52]
R. Olshansky, C. Su, J. Manning, and W. Powazinik, “Measurement of radiative and nonradiative recombination rates in InGaAsP and AIGaAs light source,” IEEE J. Quantum Electron., vol. 20, no. 8, pp. 838–854, Aug. 1984.

連結至畢業學校之論文網頁點我開啟連結
註: 此連結為研究生畢業學校所提供,不一定有電子全文可供下載,若連結有誤,請點選上方之〝勘誤回報〞功能,我們會盡快修正,謝謝!
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top
無相關期刊