臺灣博碩士論文加值系統

由於高性能機械之要求，使得齒輪動態分析日趨重要。不同於等效彈簧與等效質量之傳統離散方法，本研究以連體模式，應用動態勁性法，考慮隨著正齒輪運轉囓合點位置之改變，質量矩陣與勁性矩陣之時變特性，分析運轉囓合過程正齒輪之動態。
本文先以動態勁性法，分析旋轉非均勻截面歐拉樑之動態，考慮離心力造成之軸向硬化效應，以級數解推導出樑元素之動態勁性矩陣，並計算旋轉樑之動態變形。不同於有限元素法訴諸於元素之細分割，本研究僅以少數分割元素與少數個模態，即可獲得旋轉非均勻樑動態之準確結果。
本文應用動態勁性法，進一步分析正齒輪運轉中之動態。將輪齒分割為四個非均勻截面的提末辛科樑，每個樑元素以二階多項式來表示其外型。推導出樑元素之動態勁性矩陣之後，組合樑元素之動態勁性矩陣與非線性赫茲應力理論之勁性彈簧，構成齒輪系統之動態勁性矩陣，計算齒輪對囓合過程中輪齒之動態齒頂變形和齒根應變。齒輪實驗中，分別用 CCD 影像處理方法與應變計方法，量測齒頂變形與齒根應變，以驗證理論模式之計算結果。
論文之第五章利用所提出之分析方法，探討齒輪剛體運動產生之離心力對齒輪動態應變之影響。並探討齒輪設計參數，包括移位係數、中心距與背隙，對齒輪動態之影響。最後以多齒對之模式，計算齒輪對之齒根應變。

With an increasing demand for high performance machinery, dynamic analysis for gears has become important. Instead of discrete mass-spring models, this study presents a dynamic stiffness method to analyze spur gear dynamics. The dynamic responses of single gears and gear pairs are investigated. This continuum approach takes into account time-varying stiffness and mass matrices due to moving meshing points.
Firstly, using a dynamic stiffness method, dynamic analysis for rotating nonuniform cross-section Euler beams is carried out. Longitudinally stiffening effect is taken into account by including a geometrically nonlinear term. The dynamic stiffness of a beam element is formulated using power series. Tip deformations of the beams are calculated. In contrast to the finite element method that has to refine the element mesh, accurate dynamic response can be obtained with only few elements and few modes in the dynamic stiffness method.
The dynamic stiffness method for a Timoshenko beam is further developed and applied to spur gear dynamic analysis. Firstly, quadratic polynomials are used to represent profiles of the nonuniform cross-section beam elements for the gear blank and tooth. Then, the dynamic stiffness matrix of a Timoshenko beam element is derived. Next, assemble the dynamic stiffness matrices of the beam elements and a nonlinear Hertzian contact stiffness to form the dynamic stiffness matrix of the gear system. Finally, tip deformations and fillet strains of gears are calculated by performing modal analysis and the Runge-Kutta method. In experiment, tip deformations and fillet stains are respectively obtained using CCD image processing and a strain gauge. Experimental results serve to verify calculation results by the proposed method.
The final part of this study investigates the effect of the centrifugal force arising from the gear rotation on gear dynamics. In addition, this study also examines influences of gear parameters including the correction factor, backlash, and nonstandard center distance on gear dynamics. Fillet strains of a gear pair are calculated using a multi-tooth pair model to account for multi-tooth pairs in contact.

CHAPTER 1 INTRODUCTION . . . . . . . . . . 1
1.1 Background . . . . . . . . . . . . 1
1.2 Literature Survey . . . . . . . . . . . 2
1.3 Objective and Scope . . . . . . . . . 6
CHAPTER 2 DYNAMIC ANALYSIS FOR ROTATING BEAMS 10
2.1 Introduction . . . . . . . . . . . 10
2.2 Equation of Motion for an Euler Beam . . . 11
2.3 Dynamic Stiffness of a Rotating Beam . . . . 16
2.4 Modal Analysis . . . . . . . . . . . 25
2.5 Numerical Results and Discussion . . . . 30
CHAPTER 3 GEAR DYNAMICS . . . . . . . . . . 36
3.1 Introduction . . . . . . . . . . . . 36
3.2 Tooth Profile Description . . . . . . . . 37
3.3 Timoshenko Beam Vibration . . . . . . . . 40
3.4 Dynamic Stiffness Matrix . . . . . . . . 42
3.5 Gear Modeling . . . . . . . . . . . . 44
3.5.1 Single Gear Modeling . . . . . . . . 44
3.5.2 Single Gear Pair Modeling . . . . . . 47
3.6 Modal Analysis . . . . . . . . . . . 50
3.7 Numerical Results and Discussion . . . . . . 54
3.7.1 Single Gears . . . . . . . . . . . 54
3.7.2 Gear Pairs . . . . . . . . . . . 58
3.8 Experiments . . . . . . . . . . . . 62
3.8.1 Measurement of Tip Displacement . . . . 63
3.8.2 Measurement of Fillet Strain . . . . . . 65
CHAPTER 4 FURTHER INVESTIGATION . . . . . . . 68
4.1 Centrifugal Force Effect . . . . . . . . 68
4.2 Parametric Analysis . . . .. . . . . . . 71
4.3 Model of Multiple Tooth Pairs . . . . . . 73
CHAPTER 5 CONCLUSIONS . . . . . . . . . . . 76
REFERENCES . . . . . . . . . . . . . . . 79

Amirouche, F. M. L., Tajiri, G. C., and Valco, M. J., 1995, “Mathematical Model of a Time and Position Variant External Load on a Gear Tooth Using the Modified Timoshenko Beam Equation,” International Journal for Numerical Methods in Engineering, Vol. 39, No. 12, pp. 2073-2094.
Ankarali, A. and Diken, H., 1997, “Vibration Control of an Elastic Manipulator Link,” Journal of Sound and Vibration, Vol. 204, No. 1, pp. 162-170.
Arakere, N. K. and Nataraj, C., 1998, “Vibration of High-speed Spur Gear Webs,” ASME Journal of Vibration and Acoustics, Vol. 120, No. 3, pp. 791-800.
Ashar, K. G., 1997, Magnetic Disk Drive Technology, IEEE Press, New York.
Auciello, N. M. and Nole, G., 1998, “Vibrations of a Cantilever Tapered Beam with Varying Section Properties and Carrying a Mass at the Free End,” Journal of Sound and Vibration, Vol. 214, No. 1, pp. 105-119.
Bakr, E. M. and Shabana, A. A., 1986, “Geometrically Nonlinear Analysis of Multibody Systems,” Computers and Structures, Vol. 23, No. 6, pp. 739-751.
Banerjee, J. R. 2000, “Free Vibration of Centrifugally Stiffened Uniform and Tapered Beams Using the Dynamic Stiffness Method stiffened Timoshenko beams,”: Journal of Sound and Vibration, Vol. 247, No. 1, pp. 97-115.
Banerjee, J. R. 2001, “Dynamic Stiffness Formulation and Free Vibration Analysis of Centrifugally Stiffened Timoshenko Beams,” Journal of Sound and Vibration, Vol. 247, No. 1, pp. 97-115.
Botman, M., 1976, “Epicyclic Gear Vibrations,” ASME Journal of Engineering for Industry, Vol. 98, No. 3, pp. 811-815.
Cornell, R. W., 1981, “Compliance and Stress Sensitivity of Spur Gear teeth,” ASME Journal of Mechanical Design, Vol. 103, No. 2, pp. 447-459.
Cunliffe, F., Smith, J. D., and Welbourn, D. B., 1974, “Dynamic Tooth Loads in Epicyclic Gears,” ASME Journal of Engineering for Industry, Vol. 96, pp. 578-584.
Du, H., Lim, M. K., and Liew, K. M., 1994, “A Power Series Solution for Vibration of a Rotating Timoshenko Beam,” Journal of Sound and Vibration, Vol. 175, No. 4, pp. 505-523.
Dym, C. L. and Shames, I. H., 1973, Solid Mechanics - a Variational Approach, McGraw-Hill, New York.
Eisenberger, M., 1990, “Exact Static and Dynamic Stiffness Matrices for General Variable Cross Section Members,” AIAA Journal, Vol. 28, No. 6, pp. 1105-1109.
Eisenberger, M., 1995, “Dynamic Stiffness Matrix for Variable Cross-section Timoshenko Beams,” Communications in Numerical Methods in Engineering, Vol. 11, No. 6, pp. 507-513.
Haering, W. J., Ryan, R. R., and, Scott, R. A., 1994, “New Formulation for Flexible Beams Undergoing Large Overall Plane Motion,” Journal of Sound and Vibration, Vol. 17, No. 1, pp. 76-83.
Hatman, V. G., Haque, I., and Bagchi, A., 1995, “Dynamics of a Flexible Rotating Beam Interacting with a Flat Rigid Surface, Part I: Model Development,” Journal of Sound and Vibration, Vol. 194, No. 5, pp. 653-669.
Henshell, R. D. and Warburton, G. B., 1969, “Transmission of Vibration in Beam System,” International Journal for Numerical Methods in Engineering, Vol. 1, No. 1, pp. 47-66.
Kahraman, A., 1994, “Planetary gear train dynamics,” ASME Journal of Mechanical Design, Vol. 116, No. 3, pp. 713-720.
Kahraman, A. and Blankenship, G. W., 1999, “Effect of Involute Contact Ratio on Spur Gear Dynamics,” ASME Journal of Mechanical Design, Vol. 121, No. 2, pp. 112-118.
Kolousek, V., 1973, “Dynamics in Engineering Structures, Butterworths.
Kuang, J. H. and Lin, A. D., 2001 “The Effect of Tooth Wear on the Vibration Spectrum of a Spur Gear Pair,” ASME Journal of Vibration and Acoustics, Vol. 123, No. 3, pp. 311-316.
Leung, A. Y. T. and Zhou, W. E., 1995, “Dynamic Stiffness Analysis of Non-Uniform Timoshenko Beams,” Journal of Sound and Vibration, Vol. 181, No. 3, pp. 447-456.
Lin, H. H., Huston, R. L., and Coy, J. J., 1988, “On Dynamic Loads in Parallel Shaft Transmissions: Part I--Modeling and Analysis,” ASME Journal of Mechanism, Transmissions and Automation in Design, Vol. 110, No. 2, pp. 221-220.
Lin, H. H., Oswald, F. B, and Townsend, D. P., 1994, “Dynamic Loading of Spur Gears with Linear or Parabolic Tooth Profile Modifications,” Mechanism and Machine Theory, Vol. 29, No. 8, pp. 1115-1129.
Liu, T. S. and Lin, J. C., 1993, “Forced Vibration of Flexible Body System: a Dynamic Stiffness Method,” ASME Journal of Vibration and Acoustics, Vol. 115, No. 4, pp. 468-476.
Li, J. F., Liu, W. X., Zhu, C. M., and Tian, Z. R., 1996, Measurement of Gear Tooth Instantaneous Deformation by Optical Method, SPIE 2300, pp. 117-122.
Litvin, F. L., 1994, Gear Geometry and Applied Theory, Prentice-Hall: London.
Matusz, J. M., O’Donnel, W. J., and Erdlac, R. J., 1969, “Local Flexibility Coefficients for the Built-in Ends of Beams and Plates,” ASME Journal of Engineering for Industry, pp. 607-614.
Mayo, J. and Dominguez, J., 1997, “A Finite Element Geometrically Nonlinear Dynamic Formulation of Flexible Multibody Systems Using a New Displacements Representation,” ASME Journal of Vibration and Acoustics, Vol. 119, No. 4, pp. 573-581.
Nagaya, K., 1979, “Approximate Dynamic Analysis of Timoshenko Beams and Its Application to Tapered Beams,” Journal Acoustical Society of America, Vol. 66, pp. 794-800.
Nagaya, K., 1981, “Effects of Moving Speeds of Dynamic Loads on the Deflections of Gear Teeth,” ASME Journal of Mechanical Design, Vol. 103, No. 2, pp. 357-363.
Oswald, F. B. and Townsend, D. P., 1996, “Tooth Modification and Spur Gear Tooth Strain,” Gear Technology, Vol. 13, No. 3, pp. 20-24.
Ozguven, H. N. and Houser D. R., 1988, “Mathematical Models Used in Gear Dynamics — a Review,” Journal of Sound and Vibration, Vol. 121, No. 1, pp. 383-411.
Richards, T. H. and Leung, A. Y. T, 1977, “An Accurate Method in Structural Vibrating Analysis,” Journal of Sound and Vibration, Vol. 55, No. 3, pp. 363-376.
Seager, D. L., 1975, “Conditions for the Neutralization of Excitation by the Teeth in Epicyclic Gearing,” Journal of Mechanical Engineering Science, Vol. 17, No. 5, pp. 293-298.
Simo, J. C. and Vu-Quoc, L., 1986, “On the Dynamics of Flexible Beams under Large Overall Motions-the Plane Case: Part I,” ASME Journal of Applied Mechanics, Vol. 53, No. 4, pp. 849-854.
Stephen, N. G. and Wang, P. J., 1986, “Stretching and Bending of Rotation Beam,” ASME Journal of Applied Mechanics, Vol. 53, pp. 869-872.
Terauchi, T. Y. and Nagamura, K., 1979, “Dynamic Behavior of Planetary Gear-6th report, Displacement of Sun Gear and Ring Gear,” Bulletin of the JSME, Vol. 22, pp. 1026-1033.
Umezawa, K., Sato, T., and Ishikawa, J., 1984, “Simulation on rotational vibration of spur gears,” Bulletin of the JSME, Vol. 27, No. 223, pp. 102-109.
Umezawa, K., 1972, “The Meshing Test on Helical Gears under Load Transmission-lst Report, the Approximate Formula for Deflections of Gear Tooth,” Bulletin of the JSME, Vol. 15, No. 90, pp. 1632-1639.
Vedmar, L. and Henriksson, B. 1998, “A General Approach for Determining Dynamic Forces in Spur Gears,” ASME Journal of Mechanical Design, Vol. 120, No. 4, pp. 593-598.
Velex, P. and Maatar, M., 1996, “A Mathematical Model for Analyzing the Influence of Shape Deviations and Mounting Errors on Gear Dynamic Behaviour,” Journal of Sound and Vibration, Vol. 121, No. 5, pp. 629-660.
Vijayarangan, S. and Ganesan, N., 1993, “A Study of Dynamic Stresses in a Spur Gear under a Moving Line Load and Impact Load Conditions by a Three-dimension Finite Element Method,” Journal of Sound and Vibration, Vol. 162, No. 1, pp. 185-189.
Wang, M. J., 1999, “Photoelastic Investigation on the Bending Stress of Spur Gear Tooth in Transmission,” International Conference on Advanced Technology in Experimental Mechanics, pp. 21-24.
Weber, C., 1949, “The Deformation of Loaded Gears and the Effect on Their Load-carrying Capacity,” Sponsored Research (Germany) British Dept. of Scientific and Industrial Research, Report No. 3.
Yigit, A., Scott, R. A., and Ulsoy, A. Galip, 1987, “Flexural Motion of a Radially Rotating Beam Attached to a Rigid Body,” Journal of Sound and Vibration, Vol. 121, No. 2, pp. 201-210.
Yoon, K.Y. and Rao, S. S., 1996, “Dynamic Load Analysis of Spur Gears Using a New Tooth Profile,” ASME Journal of Mechanical Design, Vol. 118, No. 1, pp. 1-6.