本論文利用雙相流冷媒循環系統針對介電冷卻液FC-72在截面為寬20毫米、高5毫米之水平矩形流道（水力直徑為8毫米）中進行流動沸騰熱傳實驗研究，矽晶片埋至於測試段之底板中央且其尺寸為寬10毫米和長10毫米。另外，矽晶片表面包含三種不同微結構，分別是平滑、微鰭片200及微鰭片100三種形式，微鰭片200之鰭片尺寸為寬200微米、長200微米和高70微米，微鰭片100之鰭片尺寸為寬100微米、長200微米和高70微米，微鰭片200及100兩種表面之鰭片間距皆等於其鰭片寬度，而實驗的目的著重於探討在不同的介電冷卻液FC-72質通量、入口之次冷度、矽晶片之加熱通量及矽晶片表面微鰭片之幾何尺寸下對其熱傳性能及產生沸騰氣泡特徵之影響，在實驗參數範圍上，介電冷卻液FC-72質量通率從280到502 kg/m2s、FC-72於測試段入口處次冷度從0到4.3 oC、矽晶片之加熱通量從0.1到10 W/cm2而系統壓力為常壓。
由實驗結果發現隨著FC-72之質通量及次冷度的提升使得沸騰起始受到延遲，而雙相對流熱傳遞係數隨著次冷度的增加而減少但是受到質通量增加的影響則不顯著，另外，具有微鰭片結構之表面可以有效減少在單相及雙相區域之晶片表面溫度並且增加單相及雙相對流熱傳遞係數，在氣泡特徵方面氣泡脫離半徑及活躍成核孔穴密度隨著FC-72質通量及次冷度的增加而減少，而較高的FC-72質通量及較低的次冷度則導致較高的氣泡脫離頻率，再者，氣泡脫離半徑、氣泡脫離頻率及活躍成核孔穴密度則皆隨著加熱通量的上升而增加，另外，我們也發現到表面微鰭片之結構造成較小的氣泡脫離半徑、較高的氣泡脫離頻率及較高的活躍成核孔穴密度，然而，由於微鰭片100表面之鰭片間距太小因而導致其氣泡脫離半徑大於在微鰭片200之表面且具有較小的氣泡脫離頻率。
最後，將發展飽和態及次冷態之流動沸騰熱傳係數及沸騰熱通量之經驗公式。此外，氣泡特徵包含氣泡脫離半徑、氣泡脫離頻率以及活躍成核孔穴密度之量測數據的經驗公式也將被完成。

An experiment is carried out in the present study to investigate the FC-72 flow boiling heat transfer performance and associated bubble characteristics on a heated micro-pin-finned silicon chip flush mounted in the bottom of a rectangular channel. The test section is a horizontal rectangular-channel with the cross section 20 mm in width and 5 mm in height (hydraulic diameter Dh = 8 mm). The silicon chip of surface area 10 mm × 10 mm is flush mounted around the geometric center of the bottom plate of the test section. Besides, three different micro-structures of the chip surface are examined, namely, the smooth, pin-finned 200 and pin-finned 100 surfaces. The pin-finned 200 and 100 surfaces are respectively equipped with micro-pin-fins of size 200 200 70 (Wf Lf Bf) and 100 100 70 (Wf Lf Bf). The space between the two adjacent fins is equal to its width for both pin-finned 200 and pin-finned 100 surfaces. The micro-structures are fabricated on silicon chips through MEMS procedures. The experiment intends to explore the effects of the FC-72 mass flux, inlet liquid subcooling, imposed heat flux, and surface micro-structure of the silicon chip on the FC-72 flow boiling characteristics. In the experiment the coolant mass flux G ranges from 280 to 502 kg/m2s, inlet liquid subcooling ranges from 0 to 4.3 oC, imposed heat flux of the silicon chip q” ranges from 0.1 to 10 W/cm2, and the system pressure is at atmospheric pressure, covering the saturated and subcooled flow boiling.
The experimental results show that increases in the FC-72 coolant mass flux and / or inlet liquid subcooling causes a delay in the boiling incipience. The subcooled flow boiling heat transfer coefficient is reduced at increasing inlet liquid subcooling but is slightly affected by the coolant mass flux. Besides, adding the micro-pin-fin structures to the chip surface can effectively lower the surface temperature in both single- and two-phase regions and raise the single-phase convection and flow boiling heat transfer coefficients. Moreover, the mean bubble departure diameter and active nucleation site density are reduced for rises in the FC-72 mass flux and inlet liquid subcooling. Higher coolant mass flux or lower inlet liquid subcooling results in a higher mean bubble departure frequency. Furthermore, larger bubble departure diameter, higher bubble departure frequency, and higher active nucleation site density are observed as the imposed heat flux is increased. We also note that adding the micro-pin-fins to the chip decrease the bubble departure diameter and increase the bubble departure frequency. However, due to the relatively small space between the fins on the pin-finned 100 surface, the departing bubbles are larger for the pin-finned 100 surface than the pin-finned 200 surface but the bubble departure frequency is lower on the pin- finned 100 surface than the pin-finned 200 surface.
Finally, empirical correlations for the FC-72 single-phase liquid convection, saturated flow boiling, and subcooled flow boiling heat transfer coefficients for the boiling flow over the silicon chips are proposed. Besides, the experimental data for the mean bubble departure diameter, mean bubble departure frequency, and active nucleation site density are also correlated.

1. R. E. Simons, “Thermal Management of Electronic Packages,” Solid State Technology, (1983), pp. 131-137.
2. F. P. Incropera, J. S. Kerby, D. F. Moffatt and S. Ramadhyani, “Convection Heat Transfer from Discrete Heat Sources in a Rectangular Channel,” International Journal of Heat and Mass Transfer, Vol. 29, No. 7, (1986), pp. 1051-1058.
3. F. P. Incropera, “Convection Heat Transfer in Electronic Equipment Cooling,” Tractions of the ASME Journal of Heat Transfer, Vol. 110, (1988), pp. 1097-1111.
4. T. J. Heindel, F. P. Incropera, and S. Ramadhyani, “Liquid Immersion Cooling of a Longitudinal Array of Discrete Heat Sources in Protruding Substrates: I – Single-Phase Convection,” Tractions of the ASME Journal of Electronic Package, Vol. 114, (1992), pp. 55-62.
5. D. E. Maddox and I. Mudawar, “Single- and Two-Phase Convective Heat Transfer From Smooth and Enhanced Microelectronic Heat Sources in a Rectangular Channel,” Tractions of the ASME Journal of Heat Transfer, Vol. 111, (1989), pp. 1045-1052.
6. I. Mudawar and D. E. Maddox, “Enhancement of Critical Heat Flux From High Power Microelectronic Heat Sources in a Flow Channel,” Tractions of the ASME Journal of Electronic Package, Vol. 112, (1990), pp. 241-248.
7. C. O. Gersey and I. Mudawar, “Effects of Orientation on Critical Heat Flux From Chip Arrays During Flow Boiling,” Tractions of the ASME Journal of electronic package, Vol. 114, (1992), pp. 290-299.
8. K. R. Samant and T. W. Simon, “Heat Transfer from a Small Heated Region to R-113 and FC-72,” Transactions of the ASME Journal of Heat Transfer, Vol. 111, (1989), pp.1053-1059.
9. G. P. Xu, K. W. Tou and C. P. Tso, “Numerical Modeling of Turbulent Heat Transfer from Discrete Sources in a Liquid-cooled Channel,” International Journal of Heat and Mass Transfer, Vol. 41, No.10, (1998), pp. 1157-1166.
10. S. V. Garimella and P. A. Eibeck, “Heat Transfer Characteristics of an Array of Protruding Elements in Single Phase Forced Convection,” International Journal of Heat and Mass Transfer, Vol. 33, No. 12, (1990), pp. 2659-2669.
11. T. C. Willingham and I. Mudawar, “Forced-Convection Boiling and Critical Heat Flux from a Linear Array of Discrete Heat Sources,” International Journal of Heat and Mass Transfer, Vol. 35, No. 11, (1992), pp. 2879-2890.
12. T. J. Heindel, S. Ramadhyani and F. P. Incropera, ”Liquid Immersion Cooling of a Longitudinal Array of Discrete Heat Sources in Protruding Substrates: II – Forced Convection Boiling,” Transactions of the ASME Journal of Electronic Packaging, Vol. 114, (1992), pp. 63-70.
13. W. R. McGills, V. P. Carey and B. D. Strom, “Geometry Effects on Critical Heat Flux for Subcooled Convective Boiling from an Array of Heated Elements,” Transactions of the ASME Journal of Heat Transfer, Vol. 113, (1991), pp. 463-471.
14. C. P. Tso, K. W. Tou and G. P. Xu, “Flow Boiling Critical Heat Flux of FC-72 from Flush-mounted and Protruded Simulated Chips in a Vertical Rectangular Channel,” International Journal of Multiphase Flow, Vol. 26, (2000), pp. 351-365.
15. K. N. Rainey, G. Li and S. M. You, “Flow Boiling Heat Transfer from Plain and Microporous Coated Surfaces in Subcooled FC-72,” Transactions of the ASME Journal of Heat Transfer, Vol. 123, (2001), pp. 918-925.
16. Y. Ma and J. N. Chung, “A Study of Bubble Dynamics in Reduced Gravity Forced-convection Boiling,” International Journal of Heat and Mass Transfer, Vol. 44, (2001), pp. 399-415.
17. R. Situ, Y. Mi, M. Ishii and M. Mori, “Photographic Study of Bubble Behavior in Forced Convection Subcooled Boiling,” International Journal of Heat and Mass Transfer, Vol. 47 ,(2004), pp. 3659-3667.
18. C. P. Yin, Y. Y. Yan, T. F. Lin and B. C. Yang, “Subcooled Flow Boiling Heat Transfer of R-134a and Bubble Characteristics in a Horizontal Annular Duct,” International Journal of Heat and Mass Transfer, Vol. 43, (2000), pp. 1885-1896.
19. I. C. Bang, Won-Pil Baek and S. H. Chang, “A Digital Photographic Study on Nucleate Boiling in Subcooled Flow for Water and Refrigerant 134A Fluids,” Proceedings of ICONE10 10th International Conference on Nuclear Engineering Arlington, VA, April 14-18, 2002.
20. S. H. Chang, I. C. Bang and Won-Pil Baek, “A Photographic Study on the Near-wall Bubble Behavier in Subcooled Flow Boiling,” Int. J. Therm. Sci. 41 (2002) 609-618.
21. I. C. Bang, S. H. Chang and Won-Pil Baek, “Visualization of the Subcooled Flow Boiling of R-134a in a Vertical Rectangular Channel with an Electrically Heated Wall,” International Journal of Heat and Mass Transfer Vol. 47, (2004), pp. 4349-4363.
22. R. Maurus, V. Ilchenko and T. Sattelmayer, “Study of the Bubble Characteristics and the Local Void Fraction in Subcooled Flow Boiling Using Digital Imaging and Analyzing Techniques,” Experimental Thermal and Fluid Science, Vol. 26, (2002), pp. 147-155.
23. R. Maurus, V. Ilchenko and T. Sattelmayer, “Automated high-speed vedio analysis of the bubble dynamics in subcooled flow boiling,” International Journal of Heat and Fluid Flow, Vol. 25, (2004), pp. 149-158.
24. G. E. Thorncroft, J. F. Klausner and R. Mei, “An Experimental Investigation of Bubble Growth and Detachment in Vertical Upflow and Downflow Boiling,” International Journal of Heat and Mass Transfer, Vol. 41, (1998), pp. 3857-3871.
25. H. Honda, H. Takamastu and J. J. Wei, “Enhanced Boiling of FC-72 on Silicon Chips with Micro-pin-fins and Submicron-scale Roughness,” Transactions of the ASME Journal of Heat Transfer, Vol. 124, (2002), pp.383-389.
26. H. Honda and J. J. Wei, “Effects of Fin Geometry on Boiling Heat Transfer from Silicon Chips with Micro-pin-fins Immersed in FC-72,” International Journal of Heat and Mass Transfer Vol. 46, (2003), pp. 4059-4070.
27. H. Honda and J. J. Wei, “Enhanced Boiling Heat Transfer from Electronic Components by Use of Surface Microstructures,” Experimental Thermal and Fluid Science, Vol. 28, (2004), pp. 159-169.
28. H. Mizunuma, M. Behnia, and W. Nakayama, “Heat Transfer from Micro-Finned and Flat Surfaces to Flow of Fluorinert Coolant; Boiling Heat Transfer,” 1998 InterSociety Conference on Thermal Phenomena, pp.386-391.
29. C. Ramaswamy, Y. Joshi, W. Nakayama and W. B. Johnson, “Effects of Varying Geometrical Parameters on Boiling From Microfabricated Enhanced Structures,” Transactions of the ASME Journal of Heat Transfer, Vol. 125, (2003), pp. 103-109.
30. K. N. Rainey, S. M. You and S. Lee, ”Effect of Pressure, Subcooling, and Dissolved Gas on Pool Boiling Heat Transfer from Microporous, Square pin-finned Surface in FC-72,” International Journal of Heat and Mass Transfer, Vol. 46, (2003), pp. 23-25.
31. W. Qu and I. Mudawar, “Prediction and Measurement of Incipience Boiling Heat Flux in Micro-channel Heat Sinks,” International Journal of Heat and Mass Transfer, Vol. 45, (2002), pp. 3933-3945.
32. J. Lin and P. Cheng, “Bubble Cavitation in a Microchannel,” International Journal of Heat and Mass Transfer, Vol. 47, (2004), pp. 2689-2698.
33. C. Ferret, L. Falk, U. D’Ortona, A. Chenu and T. T. Veenstra, “Introduction of Image Analysis for the Quantification of the Boiling Flow Heat Transfer,” Chemical Engineering Journal, Vol. 101, (2004), pp. 357-365.
34. P. C. Lee, F. G. Tseng and C. Pan, “Bubble Dynamics in Microchannels. Part I: Single Microchannel,” International Journal of Heat and Mass Transfer, Vol. 47, (2004), pp. 5575-5589.
35. H. Y. Li, F. G. Tseng and C. Pan, “Bubble Dynamics in Microchannels. Part II: Two Parallel Microchannels,” International Journal of Heat and Mass Transfer, Vol. 47, (2004), pp. 5591-5601.
36. M. M. Shah, “A General Correlation for Heat Transfer During Subcooled Boiling in Pipes and Annuli,” ASHRAE Trans., Vol. 83, Part1, (1977), pp. 202-217.
37. J. C. Chen, “A correlation for boiling heat transfer to saturated fluids in convective flow,” Ind. Engng. Chem. Proc. Des. Dev., (5) (1966) 322-329.
38. F. W. Dittus and L. M. K. Boelter, “Heat Transfer in Automobile Radiator of the Tube Type,” Publication in Engineering, University of California, Berkley, (2) (1930) 250.
39. S. Levy, “Forced Convection Subcooled Boiling: Prediction of Vapor Volumetric Fraction,” International Journal of Heat and Mass Transfer, Vol. 10, (1967), pp. 951-965.
40. N. Koumoutsos, R. Moissis and A. Spyridonos, “A Study of Bubble Departure in Forced-Convection Boiling,” Tractions of the ASME Journal of Heat Transfer, (May 1968), pp. 223-230.
41. J. F. Klausner, R. Mei, D. M. Bernhard and L. Z. Zeng, “Vapor Bubble Departure in Forced Convection Boiling,” International Journal of Heat and Mass Transfer, (1993), Vol. 36, No. 3, pp. 651-662.
42. L. Z. Zeng, J. F. Klausner, D. M. Bernhard and R. Mei, “A Unified Model for the Prediction of Bubble Detachment Diameters in Boiling Systems – II. Flow Boiling,” International Journal of Heat and Mass Transfer, Vol. 36, No. 9, (1993), pp. 2271-2279.
43. J. F. Klauser and L. Z. Zeng, “Bubble Departure in Pool and Flow Boiling Systems: Review and Latest Developments,” Proceedings of the 2nd ASME-JSME Nuclear Engineering Joint Conference, 1993, pp. 1-6.
44. O. Zeitoun and M. Shoukri, “Bubble Behavior and Mean Diameter in Subcooled Flow Boiling,” Tractions of the ASME Journal of Heat Transfer, Vol. 118, (1996), pp. 110-115.
45. Q. Sun, R. Yang and H. Zhao, “Predictive Study of the Incipience Point of Net Vapor Generation in Low-flow Subcooled Boiling,” Nuclear Engineering and Design 225 (2003) 249-256.
46. N. Basu, G. R. Wawwier and V. K. Dhir, “Onset of Nucleate Boiling and Active Nucleation Site Density during Subcooled Flow Boiling,” Transactions of the ASME Journal of Heat Transfer, Vol. 124, (2002), pp. 717-728.
47. T. Hibiki and M. Ishii, “Active Nucleation Site Density in Boiling Systems,” International Journal of Heat and Mass Transfer, Vol. 46, (2003), pp. 2587-2601.
48. 3M company, Kataoka Japan.
49. S. J. Kline and F. A. McClintock, “Describing Uncertainties in Single-sample Experiments,” Mech. Engng 75 3-8 (1953).