臺灣博碩士論文加值系統

本研究的主要目的在於探討散熱強化型塑膠球柵電子構裝受晶片溫度循環負載下所衍生的破壞現象。本文利用數值模擬軟體ANSYS分析金線、構裝各元件介面及錫球的熱應力，並用局部對流熱傳係數法來模擬流體與固體邊界的共軛熱傳問題。結果顯示，與散熱片接觸介面的某些位置會有破壞產生，並預測晶片轉角處和最外側錫球與基板接合處會隨著晶片溫度循環次數的增加分別產生裂縫和疲勞破壞。

The aim of this study is to investigate the failure behavior induced by thermal cyclic loading of the Thermal -Enhanced PBGA. In this study, thermal stress analyses of Au wire, interfaces of different materials and solder balls are carried out by using ANSYS finite element simulation code. In addition, local heat transfer coefficients distribution is used to simulate conjugate heat transfer problem on the package surfaces.
Results show that there are defects happed in some positions contacted with heat spreader. Cracks in the chip corner points and fatigue failure in the edge balls are also predicted by increasing thermal cyclic loading times.

目 錄
內容 頁次
中文摘要I
英文摘要II
目錄III
表目錄IV
圖目錄V
符號說明IX
第一章 緒論1
第二章 物理模式8
第三章 數值方法16
3-1 流力分析16
3-2 熱傳分析19
3-3 熱應力分析22
3-4 破壞理論24
3-5 網格品質25
第四章 結果與討論33
4-1 流力及熱傳分析33
4-2 金線破壞分析45
4-3 元件破壞分析50
4-4 溫度循環對破壞行為的影響67
4-5 進口流速對破壞行為的影響73
4-6 錫球的應力分析76
4-7 對流熱傳係數對應力分佈的影響82
第五章 結論86
參考文獻87

參考文獻
1. F. Wu, J. Lau and K. L. Chen, "Thermal Evaluation of a Cost-Effective Plastic Ball Grid Array Package - NuBGA," Electronic Components and Technology Conference, 1997. Proceedings., 47th , pp. 309-318, 1997.
2. T. D. Yuan, "Convection Modeling of Flip Chip and Wirebond Surface Mounted Modules," Thermal Phenomena in Electronic Systems, 1996. I-THERM V., Inter-Society Conference on , pp. 174-179, 1996.
3. G. B. Kromann and C. W. Argento, "Thermal Enhancements for a Plastic-Ball-Grid Array Interconnect Technology: Computational-fluids Dynamics Modeling and Characterization for Low-Velocity Air-Cooling," Thermal Phenomena in Electronic Systems, 1996. I-THERM V., Inter-Society Conference on ,pp. 166-173, 1996.
4. H. Shaukatullah and M. A. Gaynes, "Comparative Evaluation of Various Types of Heat Sinks for Thermal Enhancement of Surface Mount Plastic Packages," The International Journal of Microcircuits and Electronic Packaging, Vol.18, No.3, pp. 252-259, 1995.
5. J. H. Lau and K. L. Chen, "Thermal and Mechanical Evaluations of a Cost-Effective Plastic Ball Grid Array Package," ASME Journal of Electronic Packaging, Vol. 119, pp. 208-212, September 1997.
6. E. A. Wilson, "Thermal Conductivity Analysis of Multi-Chip Micro-package," Proc. 5th Int. Thermal Conductivity Conf, pp. 49-55, 1979.
7. W. Nakayama, "Thermal Management of Electronic Equipment: A Review of Technology and Research Topics," Advance in Thermal Modeling of Electronic Components and Systems, Vol.1, pp. 1-78, Hemisphere Publishing Corp, 1988.
8. L. Yip, T. Massingill and H. Naini, "Moisture Sensitivity Evaluation of Ball Grid Array Packages," Electronic Components and Technology Conference, 1996. Proceedings., 46th , pp. 829-835, 1996.
9. I. Fukuzawa, S. Ishiguro and S. Nambu, "Moisture Resistance Degradation of Plastic LSIs by Reflow Soldering," in Proc. Int. Reliability Physics Symposium, pp. 192-197, 1985.
10. R. Lin, E. Blackshear and P. Serisky, "Moisture Induced Package Cracking in Plastic Encapsulated Surface Mount Components During Solder Reflow Process," in Proc. Int. Reliability Physics Symposium, pp. 83-89, 1988.
11. S. Liu and Y. Mei, "Behavior of Delaminated Plastic IC Packages Subjected to Encapsulation Cooling, Moisture Absorption, and Wave Soldering," IEEE Transactions on Components, Packaging, and Manufacturing Technology-Part A, Vol.18, No.3, pp. 634-645, 1995.
12. S. Liu, and Y. Mei, "An Investigation to Popcorning Mechanisms for IC Plastic Packages: EMC Cracking," The International Journal of Microcircuits and Electronic Packaging, Vol. 20, No. 3, pp. 431-446, 1997.
13. S. H. Ahn and Y. S. Kwon, "Popcorn Phenomena in a Ball Grid Array Package," IEEE Transactions on Components, Packaging, and Manufacturing Technology-Part B, Vol. 18, No. 3, August 1995.
14. J. H. Lau, "Ball Grid Array Technology," Ch.1 McGraw-Hill, New York, 1995.
15. E. Mammo, A. Mawer, A. Srikantappa, S. Vassa, G. Dody and T. Burnette, "Solder Joint Reliability Study on Area Array and Peripheral Leaded Packages," Proceeding of the SMTA national Symposium, pp.43-58, October 1995.
16. W. Jung, J. H. Lau and Y. H. Pao, "Nolinear Analysis of Full-Matrix and Perimeter-Arrayed Plastic Ball Grid Array Solder Joints," ASME paper, ASME Winter Annual Meeting, November 1996.
17. B. Su, S. Hareb and Y. C. Lee, "Solder Joint Reliability Modeling for a 540-I/O Plastic Ball-Grid-Array Assembly," Multichip Modules and High Density Packaging, 1998. Proceedings., 1998 International Conference on, pp.422-428, 1998.
18. M. Shiratori and Q. Yu, "Fatigue-Strength Prediction of Microelectronics Solder Joints under Thermal Cyclic Loading," Thermal Phenomena in Electronic Systems, 1996. I-THERM V., Inter-Society Conference on, pp.151 -157, 1996.
19. 張俊彥，鄭晃忠，積體電路製程及設備技術手冊，經濟部技術處，1997。
20. 蘇建安，葉孟考 "散熱強化型塑封球柵陣列電子構裝之分析與設計" 國立清華大學碩士論文，1999年.
21. ANSYS, 1998, User's Manual 5.5.1, Swanson Analysis Systems, Inc. Houston Pennsylvania.
22. F. B. Hildebrand, "Advanced Calculus for Applications," Edition, Prentic-Hall, 1976.
23. K. H. Huebner, E. A. Thornton and T. G. Byrom, "The Finite Element Method for Engineers," Edition, John Wiley & Sons, 1995.
24. R. Temam, "Navier Stokes Equations," Edition, North Holland Amsterdam, 1984.
25. T. J. R. Hughes, W. K. Liu and A. Brooks, "Finite Element Analysis of Incompressible Viscous Flows by the Penalty Function Formulation," J. Comput. Phys, Vol. 30, No. 1, pp.1-60, January 1979.
26. EIA/JEDEC STANDARD, Test Method A104-A, "Power and Temperature Cycling," February 1996.
27. J. A. Collins, "Failure of Materials in Mechanical Design," Ch.6, Wiley-Interscience, Ohio, 1981.