臺灣博碩士論文加值系統

在背接金屬共平面波導（Conductor-backed coplanar waveguide，CBCPW）中以主模（共平面波導模態）傳播電磁波，而此結構於任何頻率下皆會產生洩漏波向兩側傳遞。通常對於此架構下有兩種應用：一種是利用波往兩側洩漏的特性來作為天線的設計；另一種是利用特定方式來抑制此洩漏波，使它不要在兩側的方向上產生不必要的耦合及串擾。
利用全波分析去分析背接金屬共平面波導結構，得知該洩漏波以某一角度偏離主軸傳遞，使波如同行進在平板金屬波導內。而在已知偏離角度下，我們沿該角度射線蝕刻矩形槽孔。利用矩形槽孔的特性，當槽孔長邊遠大於寬邊，並約等於二分之ㄧ波長（共振長度）時，電磁波便能有效地朝空氣輻射能量形成天線，最後可得一集中的邊射輻射場形，最後設計饋入電路產生兩種方向的線性極化，而形成一高增益主波束垂直於陣列平面之高效率雙極化天線。

Conductor-backed coplanar waveguide (CBCPW) propagates electromagnetic waves via dominant modes (coplanar waveguide mode), and excites leaky wave which propagates toward both sides despite the value of the frequency. In general, there are two applications based on this structure: first is to use such property to design the antenna; the other is to suppress the leaky wave through some methods in order to decrease the unnecessary couplings and crosstalk.
Implementing the full wave analysis (Spectral Domain Approach) on the CBCPW structure, we can discover that the leaky wave propagates along a particular angle relative to the main CPW line, causing the wave to propagate as if in a parallel plate waveguide (PPW). Therefore, we can etch rectangular slots along the ground planes with the angle we have acquired. If the length of the slot is significantly longer than the width and approximately equals to half the guided wavelength, the slots fed by CBCPW will radiate power efficiently .We can thus obtain a centralized broadside radiation pattern and a dual-polarization antenna.

中文摘要 I
英文摘要 II
誌謝 IV
目錄 V
圖、表錄 VII
第一章　序論
1.1 動機與目的 1
1.2 章節介紹 2
第二章 背接金屬共平面波導槽孔天線 2
2.1 背接金屬共平面波導洩漏波原理與特性 3
2.1.1洩漏波基本原理與特性 3
2.1.2背接金屬共平面波導頻譜分析 4
2.2 平板金屬波導饋入槽孔分析 5
2.1.1 無窮大金屬面中心饋入槽孔 5
2.1.2 旋轉槽孔散射分析 6
2.1.3 等效電路 10
2.1.4 槽孔內等效磁流的幅射能量 11
2.1.5 等效串接阻抗值 13
第三章 雙線性極化背接金屬共平面波導槽孔天線設計 14
3.1 天線雙極化概述 14
3.2 線性極化天線設計流程 16
3.2.1 平板金屬波導結構之表面波偏離角度 16
3.2.2 槽孔等效電路萃取 17
3.2.3 槽孔擺設位置 18
3.3 雙線性極化天線設計模擬 22
3.3.1 線性天線陣列設計模擬 22
3.3.2 雙線性極化天線設計 28
3.3.3 90度相移岔路功率分配器 31
3.3.4 威爾森功率分配器 36
3.3.5 天線與饋入端電路合併摸擬結果 38

第四章 結論 46
參考文獻 47

[1] W. Menzel, “A new traveling-wave antenna in microstrip,” Arch. Electron. Ubertrag. Tech., vol. 33, pp. 137-140, 1979.
[2] A. A. Oliner and K. S. Lee, “The nature of the leakage from higher-order modes on microstrip line,” in Proc. 1986 IEEE MTT-S Int. Microwave Symp. Dig. , Baltimore, MD, pp. 57-60, 1986.
[3] Y. C. Shih, T. Itoh, “Analysis of conductor-backed coplanar waveguide,” Electron. Lett., vol.18, n.18, pp. 538-540, June 1982.
[4] R. J. Stevenson, “Theory of slots in rectangular waveguides,” J. App. Phys. ,vol. 19, 1948, pp. 24-38.
[5] M. Ando, K. Sakurai, N. Goto, K. Arimura and Y. Itoh, “A radial line slot antenna for 12 GHz satellite TV reception,” IEEE Trans. Antennas Propagat., vol. AP-33, no. 12, pp.1347-1353, Dec. 1985.
[6] Y. X. Cheng, “Slotted Conductor-Backed Coplanar Waveguide Antennas,” 國立交通大學電信工程學系碩士論文, 2008.
[7] T. Itoh and R. Mittra, “Spectral-domain approach for calculating the dispersion
characteristics of microstrip lines,” IEEE Trans. Microwave Theory and
Techniques, vol. 21, pp. 496-499, July 1973.
[8] R. S. Elliott, Antenna Theory and Design, Prentice Hall, Englewood Cliffs, NJ, 1981.
[9] R. Shavit, “Impedance characteristics of a slot antenna fed by a parallel-plate waveguide,” Microwave and Optical Technology Letters, vol. 14, no. 2, pp. 126-128, Feb. 1997.
[10] D,M. Pozar, Microwave Engineering,4th ed.,Wiley,New York,2011.