跳到主要內容

臺灣博碩士論文加值系統

(216.73.216.191) 您好!臺灣時間:2026/11/19 05:07
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:蔡昀璋
研究生(外文):Yun-Zhang Tsai
論文名稱:TCO/Ag/TCO結構製備高穿透的透明導電薄膜之研究
論文名稱(外文):Fabricating high transmission TCO/Ag/TCO multilayer films for transparent conductive films application
指導教授:徐瑞鴻徐瑞鴻引用關係
指導教授(外文):Jui-Hung Hsu
學位類別:碩士
校院名稱:國立中山大學
系所名稱:材料與光電科學學系研究所
學門:工程學門
學類:材料工程學類
論文種類:學術論文
論文出版年:2018
畢業學年度:107
語文別:英文
論文頁數:132
中文關鍵詞:氧化鋅/銅/銀/氧化鋅結構、透明導電膜、晶種層、光損耗、三明治結構
外文關鍵詞:Transparent conductive films、seed layer、ZnO/Cu/Ag/ZnO structure、optical loss、sandwich structure
相關次數:
  • 被引用被引用:0
  • 點閱點閱:442
  • 評分評分:
  • 下載下載:6
  • 收藏至我的研究室書目清單書目收藏:0
透明導電薄膜現今應用在許多科技產品上,如平面顯示器、電極、低散射塗層玻璃等,提供了生活上的便利性。其中以銦錫氧化物(ITO)為熱門材料,但因為銦含量少,成本過高、汙染性等問題,須尋找其他材料替代ITO。

在電極的應用上,我們使用氧化鋅/銅/銀/氧化鋅等多層膜結構(氧化物/金屬/氧化物,三明治結構)。設計此結構有兩個目的,第一,導電度方面金屬高於ITO,所以我們期待銀金屬在厚度較薄且不減少太多穿透率之下,能形成好的導電度;第二,因為搭配氧化鋅等多層膜結構,造成破壞性干涉而降低反射率,維持良好的穿透率。

然而,銀在很薄的情況下(厚度小於10奈米),在玻璃或矽基板上容易形成島狀不連續結構,造成電阻率和光散射大幅提升,使透明導電薄膜品質下降,因此,研究內容主要探討有兩個部分,第一部分,利用鍍率、銅晶種層控制下,搭配SEM、n&k分析儀、四點探針等儀器觀察結果,使銀金屬薄膜層在較薄情況下(小於8奈米),形成表面較平整的連續薄膜,而提升導電度;第二部份,使用三明治結構,讓兩層接觸面的反射產生破壞性干涉去降低反射率,並搭配模擬軟體比較,使在某些可見光波波段的穿透率能有效提升,因此,在光損耗不影響太多的情況下,選擇適當厚度且具有更多反射率的薄金屬可以應用於多層膜結構。

銅晶種層,除了減少銀薄膜層表面粗糙度,降低兩層接觸面不平整而影響的光散射、吸收等,同時造成光損耗上升,穿透度下降之外,也能幫助銀薄膜在長時間下不容易團簇,使導電和光學性質更穩定。
In nowadays, transparent conductive thin films (TCFs) are applied in many electronic devices of technologies such as flat panel display, electrode, and so on. It provides convenient life to us. The indium tin oxide is the most popular material in TCFs. However, with shortage of indium in Earth’s crust, high cost due to market demand, and toxic substance for environment. Thus, we should find alternative material to replace it.

The research of transparent conductive films applying for electrode, we used ZnO/Cu/Ag/ZnO multilayer films structure (sandwich structure of O/M/O). We designed this structure for two purposes. First, electrical conductivity in metals are higher than ITO. Thus, we expected that Ag thin having well conductivity on thinner thickness films without sacrificing much of transmittance. Second, use thin Ag layer embedded in ZnO layers for the multilayer structure. The thickness of each layer is designed to minimize the reflectance by destructive interference between two layers. Thus, it can increase transmittance in visible range.

However, ultrathin silver layer has poor wetting properties on the substrate. It is generally formed island structure when the silver layer is less than 8 nm thickness. It results in larger electrical resistance and optical scattering, to degrades the TCFs performance. Therefore, the research mainly discusses two parts. The first part is to use the SEM, n&k analyzer and four-point probe to observe the results under the control of deposition rate and copper seed layer, the silver thin layer forms smooth surface to improve conductivity on thinner thickness (less than 10 nm). The second part, using a sandwich structure to reduce the reflectance, the transmittance in the visible range can be effectively improved. Consequently, the performance (Haack’s figure of merit) can be improved by suitable adjusting the sandwich structure. For the ZnO/Cu/Ag/ZnO structure with (20/1/8/30 nm) in thickness, the figure of merit was determined to be 16817 (x10-6 Ω-1), which is higher than the figure of merit for the commercial ITO (185-nm), 15526 (x10-6 Ω-1). The sandwich layer structure, with much lower thickness, is stable under ambient condition, and better performance than the commercial ITO glasses.
論文審定書 i
中文摘要 ii
Abstract iv
List of Tables ix
List of Figures xi
Chapter 1 Introduction 1
Chapter 2 Background and literature review 4
2.1 Development of TCFs 4
2.2. Figure of merit 5
2.2.1 Sheet resistance 5
2.2.2 Haacke’s figure of merit 6
2.3 Transparent conducting film 9
2.3.1 Ultra – metal thin films 9
2.3.2 Transparent conducting oxides 11
2.3.3 Characters of zinc oxide 12
2.4 Characters of silver 13
2.4.1 Thin film of silver 14
2.4.2 The scattering hypothesis 15
2.4.3 Localized plasmon resonance 16
2.4.4 Vacuum 16
2.4.5 Deposition rate 17
2.4.6 Temperature 17
2.5 Wetting layer 17
2.5.1 Metal seed layer 18
2.5.2 Zinc oxide wetting layer 19
2.5.3 Zinc sulfide oxide wetting layer 20
2.6 Heteroepitaxy growth mechanism 20
2.6.1 Frank – van der Merwe Mode (layer by layer) 21
2.6.2 Volmer – Weber Mode (island) 22
2.6.3 Stanski – Krastanov Mode (layer plus island growth) 23
2.7 Dielectric-metal structure 24
Chapter 3 Experimental procedures 26
3.1 Substrate preparation 26
3.2 Thin film preparation 27
3.2.1 ZnO thin films 27
3.2.2 ZnS thin films 28
3.2.3 Ag thin films 29
3.2.4 Cu thin films 29
3.3 Properties measurement and analysis 30
3.3.1 3D alpha-step profilometer (α-step) 30
3.3.2 n & k analyzer 1280 30
3.3.3 Four-point probe 31
3.3.4 Scanning electron microscopy (SEM) 31
3.3.5 Energy dispersive X-ray spectrometer (EDS) 32
3.3.6 X-ray diffraction (XRD) 32
3.3.7 Zeiss Supra Multifunctional scanning electron microscope (SEM) 33
Chapter 4 Results and discussion 34
4.1 Deposition rate 34
4.2 Surface morphology 34
4.2.1 Ag (t) nm structure 34
4.2.2 Ag (t)/ Cu (1) nm structure 35
4.2.3 Ag (t)/ ZnO and Ag(t)/ ZnS structure 35
4.3 Electrical properties 36
4.3.1 Ag (t) nm structure 36
4.3.2 Ag (3)/ Cu (t) nm structure 37
4.3.3 Ag (t)/ Cu (1) nm structure 37
4.3.4 Ag (6)/ Cu (t) nm structure 38
4.3.5 Ag (t)/ ZnO and Ag(t)/ ZnS nm structure 38
4.4 Optical properties 39
4.4.1 Ag (3) nm structure 39
4.4.2 Ag (t) nm structure 40
4.4.3 Ag (t)/ Cu (1) nm structure 41
4.5 Stability 42
4.6 Design Cu/Ag/ZnO structure 43
4.6.1 Electrical properties 44
4.6.2 Optical properties 44
4.6.3 Figure of merit of Cu/Ag/ZnO 45
4.6.4 Stability 46
4.7 Design ZnO/Cu/Ag/ZnO structure 46
4.7.1 Electrical properties 46
4.7.2 Optical properties 47
4.7.3 Figure of merit of ZnO/Cu/Ag/ZnO 47
4.7.4 Compared with commercial ITO 48
Chapter 5 Conclusions 49
References 53
Tables 57
Figure 68
[1]K. Ellmer, "Past achievements and future challenges in the development of optically transparent electrodes," Nature Photonics, vol. 6, pp. 808-816, 2012.
[2]楊明輝, "透明導電膜材料與成膜技術的新發展," 工業材料, vol. 189, pp. 161-174, 1992.
[3]K. Bädeker, "Über die elektrische Leitfähigkeit und die thermoelektrische Kraft einiger Schwermetallverbindungen," Annalens der Physik homepage, vol. 327, pp. 749-766, 1907.
[4]T. Minami, "Present status of transparent conducting oxide thin-film development for Indium-Tin-Oxide (ITO) substitutes," Thin Solid Films, vol. 516, pp. 5822-5828, 2008.
[5]T. J. Coutts, D. L. Young, X. N. Li, "Characterization of transparent conducting oxides," MRS Bulletin, vol. 25, pp. 58-65, 2000.
[6]R. Groth, H. J. J. van Boort, "Low-pressure sodium lamps with indium oxide filter," Philips technical review, vol. 29, pp. 17-18, 1968.
[7]R. Kukla, "Magnetron sputtering on large scale substrates: an overview on the state of the art," Surface and Coatings Technology, vol. 93, pp. 1-6, 1997.
[8]D. B. Fraser, H. D. Cook, "Highly conductive transparent films of sputtered In2-XSnXO3-Y," Journal of The Electrochemical Society, vol. 119, pp. 1368-1374, 1972.
[9]G. Haacke, "New figure of merit for transparent conductors," Journal of Applied Physics, vol. 47, pp. 4086-4089, 1976.
[10]W. R. Grove, "On the Electro-Chemical Polarity of Gases," Philosophical Transactions of the Royal Society of London, vol. 142, pp. 87-101, 1852.
[11]K. Fuchs and N. F. Mott, "The conductivity of thin metallic films according to the electron theory of metals," Mathematical Proceedings of the Cambridge Philosophical Society, vol. 34, p. 100-108, 1938.
[12]D. S. Ghosh, Ultrathin Metal Transparent Electrodes for the Optoelectronics Industry, Springer International Publishing, Gewerbestrasse, 2013.
[13]A. Axelevitch, B. Gorenstein, G. Golan, "Investigation of Optical Transmission in Thin Metal Films," Physics Procedia, vol. 32, pp. 1-13, 2012.
[14]T. Minami, "Transparent conducting oxide semiconductors for transparent electrodes," Semiconductor Science and Technology, vol. 20, pp. S35-S44, 2005.
[15]Y. Q. Fu, J. K. Luo, X. Y. Du, A. J. Flewitt, Y. Li, G. H. Markx, A. J. Walton, W.I. Milne, "Recent developments on ZnO films for acoustic wave based bio-sensing and microfluidic applications: a review," Sensors and Actuators B-Chemical, vol. 143, pp. 606-619, 2010.
[16]K. Ellmer, "Resistivity of polycrystalline zinc oxide films: current status and physical limit," Journal of Physics D:Applied Physics, vol. 34, pp. 3097-3108, 2001.
[17]C. Charton and M. Fahland, "Optical properties of thin Ag films deposited by magnetron sputtering," Surface and Coatings Technology, vol. 174, pp. 181-186, 2003.
[18]C. A. Davis, D. R. McKenzie, R. C. McPhedran, "Optical properties and microstructure of thin silver films," Optics Communications, vol. 85, pp. 70-82, 1991.
[19]H. Wei, H. Eilers, "From silver nanoparticles to thin films: Evolution of microstructure and electrical conduction on glass substrates," Journal of Physics and Chemistry of Solids, vol. 70, pp. 459-465, 2009.
[20]C. A. Fujimori, K. J. Kühn, K. Th. Müller, U. F. Steiner, G. J. Trümper, C. C. Varma, et al., Electrical Resistivity of Thin Metal Films vol. 223: Springer Tracts in Modern Physics, 2007.
[21]K. M. McPeak, S. V. Jayanti, S. J. P. Kress, S. Meyer, S. Iotti, A. Rossinelli, D. J. Norris, "Plasmonic Films Can Easily Be Better: Rules and Recipes," ACS Photonics, vol. 2, pp. 326-333, 2015.
[22]H. C. Kim, T. L. Alford, D. R. Allee, "Thickness dependence on the thermal stability of silver thin films," Applied Physics Letters, vol. 81, pp. 4287-4289, 2002.
[23]K. Fukuda, S. H. N. Lim, A. Anders, "Coalescence of magnetron-sputtered silver islands affected by transition metal seeding (Ni, Cr, Nb, Zr, Mo, W, Ta) and other parameters," Thin Solid Films, vol. 516, pp. 4546-4552, 2008.
[24]A. Anders, E. Byon, D. H. Kim, K. Fukuda, S. H. N. Lim, "Smoothing of ultrathin silver films by transition metal seeding," Solid State Communications, vol. 140, pp. 225-229, 2006.
[25]L. Vj, N. P. Kobayashi, M. S. Islam, W. Wu, P. Chaturvedi, N. X. Fang, et al., "Ultrasmooth Silver Thin Films Deposited with a Germanium Nucleation Layer," Nano Letters, vol. 9, pp. 178-182, Jan 2009.
[26]N. Formica, D. S. Ghosh, A. Carrilero, T. L. Chen, R. E. Simpson, V. Pruneri, "Ultrastable and Atomically Smooth Ultrathin Silver Films Grown on a Copper Seed Layer," ACS Applied Materials & Interfaces, vol. 5, pp. 3048-3053, 2013.
[27]J. Yun, "Ultrathin Metal films for Transparent Electrodes of Flexible Optoelectronic Devices," Advanced Functional Materials, vol. 27, p. 1606641, 2017.
[28]J. Szczyrbowski, G. Brauer, M. Ruske, H. Schilling, A. Zmelty, "New low emissivity coating based on TwinMag (R) sputtered TiO2 and Si3N4 layers," Thin Solid Films, vol. 351, pp. 254-259, 1999.
[29]R. Dannenberga, E. Stach, D. Glenna, P. Siecka, K. Hukaria, "Microstructural and Conductivity Comparison of Ag Films Grown on amorphous TiO2 and Polycrystalline ZnO," 2001.
[30]M. Arbab, "The base layer effect on the d.c. conductivity and structure of direct current magnetron sputtered thin films of silver," Thin Solid Films, vol. 381, pp. 15-21, 2001.
[31]D.-Y. Kim, Y. C. Han, H. C. Kim, E. G. Jeong, and K. C. Choi, "Highly Transparent and Flexible Organic Light-Emitting Diodes with Structure Optimized for Anode/Cathode Multilayer Electrodes," Advanced Functional Materials, vol. 25, pp. 7145-7153, 2015.
[32]P. K. Oura, M. Katayama, A. V. Zotov, V. G. Lifshits, A. A. Saranin, Surface Science: An Introduction, Springer, Osaka, 2003.
[33]K. Tu, J. W. Mayer, L. C. Feldman, Electronic Thin Film Science: For Electrical Engineers and Materials Scientists, Macmillan, London, 1992.
[34]M. Al Shakhs, L. Augusto, L. Markley, K. J. Chau, "Boosting the Transparency of Thin Layers by Coatings of Opposing Susceptibility: How Metals Help See Through Dielectrics," Scientific Reports, vol. 6, pp. 20659-20667, 2016.
[35]R. A. Maniyara, V. K. Mkhitaryan, T. L. Chen, D. S. Ghosh, V. Pruneri, "An antireflection transparent conductor with ultralow optical loss (< 2 %) and electrical resistance (<6 Omega sq(-1), " nature communications, vol. 7, pp. 13771, 2016.
[36]W. H. Bragg and W. L. Bragg, "The Reflection of X-rays by Crystals," Proceedings of the Royal Society of London. Series A, vol. 88, pp. 428-438, 1913.
[37] B. D. Cullity, S. R. Stock, Elements of X-Ray Diffraction, Prentice Hall, New Jersey, 2014.
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top