跳到主要內容

臺灣博碩士論文加值系統

(216.73.216.176) 您好!臺灣時間:2025/09/09 19:28
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:邵文鶴
研究生(外文):Wen-Ho Shao
論文名稱:資料中心機櫃冷卻系統之研究與開發
論文名稱(外文):The Research and Development of the Data Center Cooling Rack
指導教授:李魁鵬李魁鵬引用關係
指導教授(外文):Kuei-Peng Lee
口試委員:龔育諄李文興
口試日期:2009-07-27
學位類別:碩士
校院名稱:國立臺北科技大學
系所名稱:能源與冷凍空調工程系碩士班
學門:工程學門
學類:其他工程學類
論文種類:學術論文
論文出版年:2009
畢業學年度:97
語文別:中文
論文頁數:70
中文關鍵詞:網路資料中心機櫃冷卻可程式控制器PUEPID控制節約能源
外文關鍵詞:IDCCooling RackPLCPUEPID ControlEnergy Conservation
相關次數:
  • 被引用被引用:15
  • 點閱點閱:748
  • 評分評分:
  • 下載下載:44
  • 收藏至我的研究室書目清單書目收藏:2
近年來網路資料中心(IDC)機房的發展迅速,因此需要更多的空間來存放資訊設備(IT),由於現今機房空調皆屬於大範圍冷卻,加上伺服器排列密度集高,冷熱通道概念不足,儘管環境溫度確實能達到設定範圍,但實際於IT設備的散熱效果往往有限,因此熱量不易排出,如此持續降低空調溫度往往造成過度的能源消耗。
本研究將開發一套資料中心機櫃冷卻系統,負載部份將使用電子式加熱器來取代IT設備之發熱量,兩機台並列後並可達到自體循環散熱效果,其主要針對IT設備做重點式散熱:其次將控制程式撰寫於可程式控制器(PLC)內部來控制冷媒迴路與系統監控;也紀錄機櫃降溫曲線利用系統辨識求出系統之轉移函數,及使用Z-N所建議之經驗法則計算出模擬控制參數。
實驗過程中則以定冷卻水溫、調變負載與變冷卻水溫等三組條件來進行實驗,在不同負載匹配下,調整壓縮機頻率及調變風散轉速找出機櫃之操控範圍,並使用電源使用效率指標PUE,對應於不同負載匹配時之最佳操作點,因可得到此機櫃冷卻系統之最佳操作曲線,使系統運行於適合之頻率與風機轉速下來達到省電之效果,即可達到節能源之目標。
由定冷卻水溫實驗結果得知,在滿載操作時可得到最佳PUE值為1.47,並與國內機房實際量測平均PUE值1.9與美國ASHRAE 300RT等級之標準PUE值為1.5相較之下,其機櫃冷卻系統之電能使用效率皆優於國內外之案例。
In recent years, the Internet data center (IDC) of the rapid development of the computer room, so need more space to store Information Technology (IT) equipment. As a result of the computer room air conditioners in cooling are large-scale in today’s, coupled with the server set with a high density, the concept of cold and hot channels inadequate, despite the ambient temperature range will be able to achieve the set point. And the actual IT equipment in the cooling effect is often limited so difficult to emit heat, continuing to reduce air-conditioning temperature often results in excessive energy consumption.
This study will develop a set of data center cooling rack, the electronic-type heater used in the rack as IT equipment heat generation. The two machines, IT rack and cooling rack, side by side can be reached after the cooling effect from the systemic circulation. The cooling rack functions as spot and closed loop cooling effect on the server rack. The control program was wrote in the Programmable Logic Controller (PLC) to control the internal cooling circuit and system monitoring; also to record rack cooling profile. According to the cooling profile obtained, the parameters of analog control can be calculated through the system identification method, transfer function, and the Z-N rule. The optimum operation condition and the maximum energy efficiency, PUE, of the cooling system were verified through a series of testing conditions including constant condenser cooling water temperature, variable heat load and variable condenser cooling water temperature.
The maximum energy efficiency, PUE, is 1.47 under full load and the condenser cooling water temperature per ARI 550/590. This maximum energy efficiency PUE is much better than the average PUE 1.9 of the surveyed data in Taiwan and also better than the PUE 1.5 of design per ASHRAE 90.1-2007.
摘 要 i
ABSTRACT ii
誌 謝 iv
目 錄 v
表目錄 vii
圖目錄 viii
第一章 緒論 1
1.1 研究背景與動機 1
1.2 文獻回顧與探討 4
1.3 研究目的 8
第二章 IDC現有設備類型與能源評估 9
2.1 IDC機房空調系統類型 9
2.1.1 直膨式空調系統 9
2.1.2 中央空調系統 10
2.1.3 外氣預先處理空調系統 11
2.2 IDC機房空調設計與送風方式 13
2.2.1 高架地板送風方式 15
2.2.2 頂板(天花板)分配方式 16
2.2.3 出風口的配置 17
2.3 IT設備散熱方式 18
2.3.1 冷熱通道概念 18
2.3.2 IT風扇擺設位置 21
2.3.3 背板式冰水熱交換系統 22
2.4 IDC能源評估方式 23
第三章 控制方法與系統辨識 25
3.1 傳統PID控制 25
3.1.1 PID控制架構 28
3.2 PLC之PID控制系統 30
3.3 系統辨識 33
3.4 Ziegler-Nichols法則 35
3.4.1 頻率響應法 35
3.4.2 步階響應法 37
第四章 設備開發與實驗 38
4.1 設備與系統配置 38
4.1.1 機櫃架構 38
4.1.2 系統迴路設備 41
4.1.3 控制與通訊 47
4.2 量測方法 49
4.2.1 量測設備 50
4.3 求得系統轉移函數 54
第五章 結果與討論 56
5.1 定冷卻水溫實驗結果 56
5.1.1 定冷卻水溫結果分析 58
5.2 調變負載實驗結果 60
5.2.1 調變負載結果分析 61
5.3 變冷卻水溫實驗結果 63
5.3.1 變冷卻水溫結果分析 64
第六章 結論 66
6.1 研究結論 66
6.2 後續研究建議 67
參考文獻 68
[1] C.Kurkjian , " Air conditioning design for data centers, "Accommodating current loads and planning for the future, EYP Mission Critical Facilities, 2006.
[2] 張奇、黃怡娟、吳善同、朱南勳,「綠化關鍵分析」,MIC, 2008。
[3] Suhas V. Patankar and Kailash C. Karki, Ph. D. “Distribution of Cooling Airflow in a Raised-Floor Data Center,” ASHRAE Transactions,Vol.110,Part 2. 2004, pp.629~634.
[4] S. Shrivastava, B. Sammakia, R. Schmidt, and M. Iyengar,“Comparative analysis of different data center airflow management configurations”, Proceedings of the ASME InterPACK ’05 Conference, San Francisco, CA, paper IPACK2005-73234, 2005.
[5] J. VanGilder, and R. Schmidt,“Airflow uniformity through perforated tiles in a raised floor data center”, Proceedings of the ASME InterPACK ’05 Conference, San Francisco, CA, paper IPACK2005-73375, 2005.
[6] S. Bhopte, B. Sammakia, R. Schmidt, M. Iyengar, and D. Agonafer,“Effect of under floor blockages on data center performance”, Proceedings of the inter society conference on thermal phenomena(ITherm), San Diego, CA, MAY 30-June 2, 2006.
[7] S. Patankar, V., and K.C. Karki,“Distribution of cooling airflow in a raised flow data center”, ASHRAE Transactions 110(2):629-34, 2004.
[8] G.Malone,Data Center TCO Benefits of Reduced System Airflow,IEEE 1199-1202.
[9] Cullen E. Bash, Chandrakant D. Patel, Ratnesh K. Sharma Hewlett-Packard Laboratories,Dynamic Thermal Management of Air Cooled Data Centers,2006 IEEE 445-452.
[10] Mingfang Du, Tongshun Fan, Wei Su, Hongxing Li ,Design of a New Practical Expert Fuzzy Controller in Central Air Conditioning Control System, 2008, IEEE Pacific-Asia Workshop on Computational Intelligence and Industrial Application.
[11] S.Soyguder, M.Karakose,H.Alli, Design and simulation of self-tuning PID-type fuzzy adaptive control for an expert HVAC system, Expert Systems with Applications 36 ,2009,pp.4566–4573.
[12] S.Soyguder , H.Alli,Predicting of fan speed for energy saving in HVAC system based on adaptive network based fuzzy inference system, Expert Systems with Applications 36 ,2009, pp.8631–8638.
[13] L.Hua, S.K. Jeong, S.S.You,Feedforward control of capacity and superheat for a variable speed refrigeration system, Applied Thermal Engineering 29 ,2009, pp.1067–1074.
[14] F.Mnif, New tuning rules of PI-like controllers with transient performances formonotonic time-delay systems, ISA Transactions 47 ,2008,pp.401–406.
[15] ASHRAE,ASHRAE Handbook - HVAC Applications,Data Processing and Electronic Office Areas,2007,pp.17.1-17.16.
[16] 鄧南平,Data Center 消災延壽節能法門,IBM Corporation,2007年。
[17] 吳建德,電腦機房空調氣流分析與節能潛力評估,碩士論文,國立台北科技大學,能源與冷凍空調系所,台北,2009年。
[18] 李魁鵬,王獻堂,朱國權,吳建德,電機月刊,綠色資料中心國際現況與技術,不斷電系統與電源供應裝置專輯,第223期,2009年。
[19] 謝閔宏,一階具時間延遲系統以實驗方法進行PI/PID控制器的微調,碩士論文,國立屏東科技大學,機械工程所,屏東,2001年。

[20] 郭誌宏,節能外氣空調系統之研究與開發,碩士論文,國立台北科技大學,能源與冷凍空調系所,台北,2008年
[21] 許富春,滿液式變頻冰水主機之模糊PID嵌入式控制器研究,碩士論文,國立台北科技大學,能源與冷凍空調系所,台北,2008年。
[22] 陳湢文,變頻螺旋式冰水機節能效益之研究,碩士論文,國立台北科技大學,能源與冷凍空調系所,台北,2008年。
[23] 黃崇傑,網路資料中心內密閉式伺服器機櫃散熱節能分析研究,碩士論文,國立台北科技大學,能源與冷凍空調系所,台北,2008年。
[24] 劉偉忠,資訊管理系統機房空調箱最佳運轉模式分析,碩士論文,國立台北科技大學,能源與冷凍空調系所,台北,2007年。
[25] 張碩,自動控制系統,台北:鼎茂圖書出版股份有限公司,2003,第8.14-8.17頁。
[26] 蘇金佳譯,冷凍與空調,台北:美商麥格羅.希爾國股份有限公司,2006,第249-340頁。
[27] 陳正義,開放式可程式控制器程式設計與應用,台北:全華科技圖書股份有限公司,2004,第14.3-14.9頁。
[28] 洪志育、允成科技,富士人機介面,台北:新文京開發出版社,2003年。
[29] 雙象貿易股份有限公司譯,三菱可程式控制器FX2N中文使用手冊,台北:雙象貿易股份有限公司,2006年。
[30] 雙象貿易股份有限公司譯,三菱可程式控制器類比模組 中文使用手冊,台北:雙象貿易股份有限公司,2006年。
連結至畢業學校之論文網頁點我開啟連結
註: 此連結為研究生畢業學校所提供,不一定有電子全文可供下載,若連結有誤,請點選上方之〝勘誤回報〞功能,我們會盡快修正,謝謝!
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top