跳到主要內容

臺灣博碩士論文加值系統

(216.73.216.206) 您好!臺灣時間:2026/11/21 20:29
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

我願授權國圖
: 
twitterline
研究生:張濤
研究生(外文):Yanto
論文名稱:依據印尼中爪哇省農民人體計測研究 –研擬與建議農具新國家標準
論文名稱(外文):Anthropometric Study of Indonesian Farmers in Central Java, Indonesia – toward evaluation and propose the newly dimensions of national standard of agriculture tools
指導教授:呂志維呂志維引用關係
指導教授(外文):Chih-Wei Lu
學位類別:博士
校院名稱:中原大學
系所名稱:工業與系統工程研究所
學門:工程學門
學類:工業工程學類
論文種類:學術論文
論文出版年:2018
畢業學年度:106
語文別:英文
論文頁數:95
中文關鍵詞:印尼農民、印尼國家標準尺寸、人體計測值、農業工具
外文關鍵詞:Indonesian farmers、anthropometric dimensions、Indonesian national standard、agriculture tools
相關次數:
  • 被引用被引用:0
  • 點閱點閱:242
  • 評分評分:
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:1
本研究人體計測數據來源為印尼中爪哇省三個聚落鄉村的農民,參與研究受測者共有314位,每位受測者共需要測量69項人體計測,測量內容包含三種握力方式與肺活量,在受測過程中受測者均以站姿及坐姿姿勢進行測量。在69項人體計測中,其中25項屬於手部的人體計測,計測數值將以表格的方式呈現出印尼男性與女性受測者的最小值、最大值、平均值、標準誤差(SD)、平均標準誤差(SEM)、變異係數(CV),與身體每項部位的第5百分位數以及第95百分位數。
本研究樣本皆取自於職業屬性相同之農民,根據男、女性統計分析的結果,我們可以觀察到43項測量值中有40項是有顯著差異的, 在這40項測量內,男性農民有38項人體計測值較為顯著,其餘2項(大腿厚度與胸部深度)女性農民較為顯著;至於手部測量,除了拇指厚度、食指寬度和厚度、拇指間的手部厚度、手腕寬度之外,男性的測量結果也相對顯著於女性計測值。研究中考量到平均值百分比的差異性,本研究將參照國內人體計測資料庫的參考計測值與印尼從事相關研究者之文獻與研究。
  在本研究中,農民之間的人體計測值也相對與其他族群進行比較,如印度人、阿爾及利亞人、尼日利亞人、菲律賓人和葡萄牙人,以下為印尼農民於各族群間的平均差異百分比:印尼之於印度平均差異百分比為0%~18%,阿爾及利亞為1.1%~21.4%,尼日利亞為0.5%~24.4%,菲律賓為0.3%~12.7% ,葡萄牙為0.6%~27.4%,因此得出結論,印尼與印度男、女性農民之間的人體計測值、特徵是較為相近的;然而,以整體身形比較來說,印尼的男、女性農民相較於其他族群顯得較為矮小。
  至於應用人體計測值給予評估與建議於農業工具尺寸,本研究將國家標準中鐮刀(SNI 02-1456-1989)、斧頭(SNI 05-0551 -1989)的數據加以評估而提出建議尺寸,並額外提出鋤頭的建議尺寸於國家標準尺寸。透過人體計測數據的參考與應用,發現讓使用者感到其安全度、舒適度、有效率之原因在於農用工具的握把長度與握柄直徑,本研究將會針對鐮刀、斧頭、鋤頭個別提出適當的握把長度與握柄直徑進行探討。對於鐮刀,本研究因考量到拇指間手部厚度的95百分位數,提出握把適當長度為12公分到22公分;則握把直徑部分,因拇指和食指之間會有重疊交錯的部分考量,因此將握把直徑建議三種不同尺寸分別為小(2.9~3.3公分)、中(3.3~3.8公分)、大(3.8~4.2公分)。對於斧頭,本研究因考量到拇指間手部厚度的95百分位數與額外增加的容許值,提出斧頭握把適當長度為15公分到22公分;則握把直徑部分,握把的設計是需要符合使用者的,使用時手指間沒有重疊交錯,可有效地降低抓握時所需要出的力量,因此將握把直徑建議三種不同尺寸分別為小(3.5~4公分)、中(4~4.6公分)、大(4.6~5公分)。對於鋤頭,以站姿人體計測尺寸作為考量,鋤柄的建議適當長度為76公分到106公分;則鋤柄直徑之建議值與斧頭相同。
  由於人體間的尺寸會隨著時間而改變,本研究在此建議政府主管機關能夠定期評估與修改農業工具相關的尺寸標準,也希望政府主管機關能夠修訂與採納經由本研究發現的建議人體計測值於國家標準尺寸。
This study collected anthropometric data of Indonesian farmers in Central Java Province, Indonesia. A number of 314 samples participated in this study. They were taken from three residencies in Central Java, Indonesia. A number of 69 anthropometric dimensions including three grip strengths and lung capacity were measured, taken when subject in the standing and sitting postures. Out of 69 dimensions, 25 dimensions were hand anthropometry presented in separate table. The values of minimum, maximum, mean, standard deviation (SD), standard error of mean (SEM), coefficient of variation (CV), 5th and 95th percentile values of each body dimension were presented for both males and females.
Based on statistical analysis between males and females, it can be observed that 40 0f 43 measurements were significantly different. Of these 40 measurements, female farmers are bigger in two dimensions (thigh thickness and chest depth); males are higher and bigger for the remaining 38 dimensions. As for hand anthropometry, males are significantly longer and bigger than females, except for thumb thickness, index finger breadth and thickness, hand thickness with thumb included, and wrist width.
The comparisons were also made between anthropometric data in this study with those of other studies by Indonesian researchers. Considering the percentage of mean differences, anthropometric dimensions of Indonesian farmers in this study are found to be similar with previous studies. This finding may be due to the fact that both studies involved samples with the same occupation as farmer. Anthropometric dimensions of farmers of the present study were also compared with those of other nationalities, namely Indian, Algerian, Nigerian, Filipino and Portuguese. From the stature comparisons, Indonesian farmers are shorter than those of other nationalities for both male and female. The percentage of mean differences between Indonesian farmers and those of other nationalities are ranging from 0% to 18% for Indian farmers, from 1.1% to 21.4% for Algerian farmers, from 0.5% to 24.4% for Nigerian farmers, from 0.3% to 12.7% for Filipino workers, and from 0.6% to 27.4% for Portuguese workers. Findings conclude that the general anthropometric characteristics of Indonesian farmers were found to be similar with Indian farmers for both male and female.
As for the application of anthropometric data to evaluate and propose the national standard dimensions of agriculture tools, this study highlighted the use of such data to evaluate and propose the dimensions of sickle (SNI 02-1456-1989), choppers (SNI 05-0551-1989), and to propose the national standard dimensions of hoe handle. Regarding those tools, two handle dimensions were identified as key dimensions for effective, safe and comfort use by the users i.e. the length and diameter of handle. For the sickle, this study proposed handle length of the sickle from 12.0 cm to 22.0 cm by considering the 95th percentile of hand breadth at thumb. For handle diameter, a-three sizes policy (small, medium and large) to accommodate most users within the population was proposed i.e. 2.9-3.3 cm, 3.3-3.8 cm, 3.8-4.2 respectively. For the chopper, this study proposed handle length of the sickle from 15.0 cm to 22.0 cm. Meanwhile for handle diameter a-three sizes policy was also proposed with the sizes are 3.5-4 cm (small), 4-4.6 cm (middle) and 4.6-5 cm (large). As for the hoe, this study also proposed the same three sizes of handle diameter as proposed for chopper. Meanwhile, by considering a few anthropometric dimensions in the standing posture, the recommended lengths of hoe handle are ranging from 76 cm to 106 cm. Further, findings in this study hopefully could be used by the responsible authority to revise and issue the newly dimensions of such national standard. This study also recommended to the authority to periodically evaluate and revise the dimensions of national standard of agriculture tools due to the fact that anthropometric dimensions might change over time.
Contents

摘要 I
ABSTRACT II
ACKNOWLEDGEMENT III
CONTENTS IV
LIST OF TABLES VI
LIST OF FIGURES VII
LIST OF EQUATIONS IX


CHAPTER 1 INTRODUCTION 1
1.1 Background of the Study 1
1.2 Problem Statement 2
1.3 Research Questions 3
1.4 The Study Objectives 4
1.5 Expected Research Ouputs 4

CHAPTER 2 LITERATURE REVIEW 5
2.1 Ergonomics and Its Definition 5
2.2 Brief History of Ergonomics 5
2.3 Ergonomics and Domain Specialization 6
2.4 Anthropometry and the History of Human Dimensions 7
2.5 Human Diversity and Factors that Affect Anthropometric Data 8
2.6 Measurement Instruments and Technique 8

CHAPTER 3 METHODOLOGY 11
3.1 Sampling and Sampling Method 11
3.2 Anthropometric Dimensions of the Farmers 11
3.3 Measuring Instruments 21
3.4 Measurers 22
3.5 Procedures 23
3.6 Data Analysis 24
3.7 Application of Data for the Proposed Dimensions of National Standard of Agriculture Tools 25
3.7.1 The revised standard of the handle of sickle 25
3.7.2 The revised standard of the handle of chopper 26
3.7.3 The proposed standard of the handle of hoe 27

CHAPTER 4 RESULTS AND ANALYSIS 29
4.1 Demographic Data of the Participants 29
4.2 Anthropometric Data of the Farmers in Central Java, Indonesia 30
4.2.1 Normality test results 30
4.2.2 Anthropometric data differences between male and female farmers 34
4.2.3 Anthropometric data differences among different regencies 36
4.2.4 Anthropometric data differences among different age groups 38
4.3 Comparisons Between Anthropometric Data of the Farmers in This Study with Those of Previous Study 41
4.4 Comparisons Between Anthropometric Data of the Farmers in This Study with Other Nationalities 47

CHAPTER 5 DISCUSSION AND APPLICATION 51
5.1 Discussion 51
5.1.1 Anthropometric data in this study 51
5.1.2 Comparisons of data in this study with those of other nationalities 52
5.2 Application of Anthropometric Data for the Proposed Dimensions of National Standard of Agriculture Tools 54
5.2.1 The current dimensions of national standard of agriculture tools and the percentile that the current standard could cover 54
5.2.2 The proposed dimensions of national standard for handle of the sickle 58
5.2.3 The proposed dimensions of national standard for the chopper handle 63
5.2.4 The proposed dimensions of national standard for the hoe handle 66
5.2.5 Application of the data for other agriculture tools 73

CHAPTER 6 CONCLUSION AND RECOMMENDATION 75
6.1 Conclusion 75
6.2 Contribution of This Dissertation 78
6.3 Highlight and Limitation of The Study 78
6.4 Recommendation 79
6.4.1 Recommendation for future research 79
6.4.2 Recommendation for industry and goverment authority 79

REFERENCES 81
BIOGRAPHY 85











List of Tables
Table 3.1 Definition of anthropometric dimensions considered in this study 12
Table 3.2 Definition of hand anthropometric dimensions considered in this study 14
Table 3.3 Anthropometric dimensions and application in this study or potential application 18
Table 3.4 Hand anthropometry and application in this study or potential application in the future 20
Table 4.1 Profile of participants in this study 30
Table 4.2 Anthropometric data of Indonesian farmers 31
Table 4.3 Hand anthropometry of Indonesian farmers 32
Table 4.4 Normallity test results of anthropometric data in this study 33
Table 4.5 Normallity test results of hand anthropometry in this study 34
Table 4.6 Anthropometric comparison between male and female farmers 35
Table 4.7 Hand anthropometric comparison between male and female farmers 36
Table 4.8 Anthropometric comparison of farmers among three regencies using Anova 37
Table 4.9 Hand anthropometric comparison of farmers among three regencies using Anova 38
Table 4.10 Anthropometric comparison for different age groups using Anova 39
Table 4.11 Hand anthropometric comparison for different age groups using Anova 40
Table 4.12 Anthropometric comparison between this study and previous study
(Syuaib, 2015) for males 42
Table 4.13 Anthropometric comparison between this study and previous study
(Syuaib, 2015) for females 43
Table 4.14 Hand anthropometric comparison between this study and previous study
(Syuaib, 2015) for males 44
Table 4.15 Hand anthropometric comparison between this study and previous study
(Syuaib, 2015) for females 44
Table 4.16 Comparison of anthropometry of this study with those of previous studies for males 45
Table 4.17 Comparison of anthropometry of this study with those of previous studies for females 46
Table 4.18 Comparison of anthropometry of male population among different countries 48
Table 4.19 Comparison of anthropometry of female population among different countries 49
Table 4.20 Hand anthropometry of male population among different countries 50
Table 4.21 Hand anthropometry of female population among different countries 50
Table 5.1 Hand anthropometry for the proposed dimensions of the handle diameter of sickle 61
Table 5.2 Comparison of handle diameter of sickle in this study, actual use by farmers,
available in the market and recommended dimensions 62
Table 5.3 Hand anthropometry for the proposed dimensions of the handle diameter of chopper 64
Table 5.4 Comparison of handle diameter of choppers in this study, actual use by farmers,
available in the market and recommended dimensions 66
Table 5.5 Body angle during the operation of a hoe based on observation 70
Table 5.6 Parameter used to determine the handle length of traditional hoe 70
Table 5.7 Comparison of the handle length of hoe among different studies and in the market 73
Table 5.8 Recommendation for handle length and diameter of hoe in this study 73

List of Figures
Figure 2.1 A set of conventional measuring instruments 9
Figure 2.2 Morant technique with the grid system 9
Figure 2.3 Integrated composited anthropometer to measure subjects 10
Figure 2.4 Anthroscan (a), position of subject (b) and measurement output on computer screen (c) 10
Figure 3.1 Anthropometric dimensions measured in this study, taken when subject in the standing posture 16
Figure 3.2 Anthropometric dimensions measured in this study, taken when subject in the sitting posture 16
Figure 3.3 Measurement of grip strength, taken when subject in the standing posture 17
Figure 3.4 Hand anthropometric dimensions measured in this study 17
Figure 3.5 Measuring instruments which were used in this study 22
Figure 3.6 Spiro meter to measure lung capacity (a) and a self- design wooden cone for hand grip diameter (b) 22
Figure 3.7 The standard posture during measurement 24
Figure 3.8 The three most common use of traditional agriculture tools 25
Figure 3.9 A farmer uses a sickle (a) and the handle dimensions of a sickle (b) 26
Figure 3.10 A farmer uses a chopper (a) and illustration of chopper and the handle (b) 27
Figure 3.11 Chopper with handle part dimensions (L and D) and blade (B1) 27
Figure 3.12 A farmer uses hoe (a) and the handle dimensions of a hoe (b) 28
Figure 4.1 Distribution of samples based on age group according to Ministry of Health (2009) 29
Figure 4.2 Distribution of samples from three regencies in Central Java Province 29
Figure 4.3 Mean average of stature for different age groups 40
Figure 5.1 The percentile that the current standard could cover for handle length of sickle
for male farmers 55
Figure 5.2 The percentile that the current standard could cover for handle length of sickle for female farmers 55
Figure 5.3 The percentile that the current standard could cover for handle diameter of sickle for male farmers 56
Figure 5.4 The percentile that the current standard could cover for handle diameter of sickle for female farmers 56
Figure 5.5 The percentile that the current standard could cover for handle diameter of chopper for male farmers 57
Figure 5.6 The percentile that the current standard could cover for handle diameter of chopper for female farmers 57
Figure 5.7 A sickle with the handle and blade part 58
Figure 5.8 A farmer uses a sickle for various operations 59


Figure 5.9 The operation of sickle by farmer with 50% and 30% overlap between thumb and middle finger 61
Figure 5.10 A few different types of sickle in the market and used by farmers 63
Figure 5.11 Illustration of the use of chopper to cut down the object by delivering a blow 63
Figure 5.12 Max. grip diameter of males and females (a) and percentile values ofcombined data (b) 64
Figure 5.13 Three sizes based on percentile values to accommodate variability of max.grip diameter 65
Figure 5.14 A few types of chopper used by farmers (a) and a few examples of handle (b) 66
Figure 5.15 A hoe with handle and blade part 67
Figure 5.16 The operation of hoe by a farmer 67
Figure 5.17 Farmer’s anthropometry (a) and initial and end position during the operations of a hoe (b, c) 68
Figure 5.18 The possible postures during a hoe operation by farmers based on field observation and literature 71
Figure 5.19 Gripping area during the operation of a hoe by a farmer 72
Figure 5.20 A few examples of hoe handle available in the market and adjustment area for users 71
















List of Equations

Equation 3.1 n=(3.006 x CV/α)^2 11
Equation 5.1 Handle length of sickle > Hand breadth at thumb + 1.0 cm 54
Equation 5.2 Handle diameter of sickle < Max. grip diameter of the hand - 0.5 cm 55
Equation 5.3 Handle diameter of chopper < Max. grip diameter of the hand - 0.5 cm 57
Equation 5.4 CL=(AD.cos⁡β3+ DE.cos⁡〖β4+EF.cos⁡〖β5-AB.cos⁡〖β2-BC.cos⁡β1 〗 〗 〗)/cos⁡β0 70
1.Abeysekera, J., & Shahnawaz, H. (1989). Body size variability between people in developed and developing countries and its impact on the use of imported goods. International Journal of Industrial Ergonomics, 4, 139–149.
2.Barroso M.P., Arezes P.M., Luis G.C., & Miguel A.S. (2005). Anthropometric study of Portuguese workers. International Journal of Industrial Ergonomics, 35, 401–410.
3.Bolstad, G., Benum, B., & Rokne, A. (2001). Anthropometry of Norwegian light industry and office workers. Applied Ergonomics, 32, 239–246.
4.Bridger, R.S. (2009). Introduction to Ergonomics (3rd ed.). Boca Raton, FL: CRC Press.
5.Chuan, T.K., Hartono, M., & Kumar, N. (2010). Anthropometry of the Singaporean and Indonesian populations. International Journals of Industrial Ergonomics, 40, 757–766.
6.Dewangan, K.N., Owarya, C., & Datta, R., K. (2008). Anthropometric data of female farm workers from north eastern India and design of hand tools of the hilly region. International Journal of Industrial Ergonomics, 38, 90–100.
7.Dewangan, K.N., Kumar, G.V.P., Suja, P.L., & Choudhury, M.D. (2005). Anthropometric dimensions of farm youth of the north-eastern region of India. International Journal of Industrial Ergonomics, 35, 979–989.
8.Dewangan, K.N., Owarya, C., & Datta, R.K. (2010). Anthropometry of male agricultural workers of north-eastern India and its use in design of agricultural tools and equipment, International Journal of Industrial Ergonomics, 40, 560–573.
9.Edris Ghaderi, E., Maleki, A., & Dianat, I. (2014). Design of combine harvester seat based on anthropometric data of Iranian operators. Applied Ergonomics, 44, 810–816
10.Grant, K.A, Habes, D.J, & Steward, L.L. (1992). An analysis of handle designs for reducing manual effort: The influence of grip diameter. International Journal of lndustrial Ergonomics, 10, 199–206
11.García-Caceres, R.G., Felknor, S., Cordoba, J.E., Caballero, J.P., & Barrero, L.H. (2012). Hand anthropometry of the Colombian floriculture workers of the Bogota plateau. International Journal of Industrial Ergonomics, 42, 183–198.
12.Hanson, L., Sperling, L., Gard, G., Ipsen, S., & Vergara, C.O. (2009). Swedish anthropometrics for product and workplace design. Applied Ergonomics, 40, 797–806.
13.Hsiao, H., Whitestone, J., Bradtmillers, B., Whisler, R., Zwiener, J., Lafferty, C., Kau, T.Y., & Gross, M. (2005). Anthropometric criteria for the design of tractor cabs and protection frames. Ergonomics, 48 (4), 323–353.
14.Hu, H., Li, Z., Yan, J., Wang, X., Xiao, H., Duan, J., & Zheng, L. (2007). Anthropometric measurement of the Chinese elderly living in the Beijing area. International Journal of Industrial Ergonomics, 37, 303–311.
15.IEA. (2015). Definition and Domain of Ergonomics. Retrieved from http://www.iea.cc/whats/index.html.
16.Iseri, A., & Arslan, N. (2009). Estimated anthropometric measurements of Turkish adults and effects of age and geographical regions. International Journal of Industrial Ergonomics, 39, 860–865.
17.Jee, S.C., & Yun, M.H. (2016). An anthropometric survey of Korean hand and hand shape types. International Journal of Industrial Ergonomics, 53, 10–18.
18.Khadem, M.M., & Islam, M.D. (2014). Development of anthropometric data for Bangladeshi male population. International Journals of Industrial Ergonomics, 44, 401–412.
19.Klamklay, J., Sungkhapong, A., Yodpijit, N., & Patterson, P.E. (2008). Anthropometry of the southern Thai population. International Journal of Industrial Ergonomics, 38, 111–118.
20.Kothiyal, K., & Tettey, S. (2001). Anthropometric data of elderly people in Australia. Applied Ergonomics, 31, 329–332.
21.Kroemer, K., Kroemer, H., & Kroemer-Elber, K. (2001). Ergonomics How to Design for Ease and Efficiency. New Jersey, NJ: Prentice Hall, Inc.
22.Kroemer, K.H.E. (2003). Engineering Anthropometry. In Karwoski, K., Marras, W.S. (Ed.), Occupational Ergonomics: Principles of Work Design (pp. 9-1 – 9-27). Boca Raton, FL: CRC Press.
23.Kroemer, K.H.E. (2009). Fitting the Human: Introduction to Ergonomics. (6th ed.). Boca Raton, FL: CRC Press.
24.Kroemer, K.H.E. & Grandjean, E. (2007). Fitting the Human: A Textbook of Occupational Ergonomics. (5th ed.). Boca Raton, FL: CRC Press.
25.Kong, Y.K. & Lowe, B.D. (2005). Optimal cylindrical handle diameter for grip force tasks. International Journal of Industrial Ergonomics, 35, 495–507.
26.Lewis, W.G. & Narayan, C.V. (1993). Design and sizing of ergonomic handles for hand tools. Applied Ergonomics, 24 (5), 351–356
27.Mokdad, M., (2002). Anthropometric Study of Algerian Farmers. International Journal of Industrial Ergonomics, 29, 331–341.
28.Marras, W.S. & Kim, J. Y. (1993). Anthropometry of Industrial Populations. Ergonomics, 36 (4), 371–378.
29.Molenbroek, J.F.M., Kroon-Ramaekers, Y.M.T., & Snijders, C.J. (2003). Revision of the design of a standard for the dimensions of school furniture. Ergonomics, 46(7), 681–694.
30.Mououdi, M.A. (1997). Static anthropometric characteristics of Tehran University students age 20–30. Applied Ergonomics, 28 (2), 149–150.
31.Mokdad, M. (2002). Anthropometric Study of Algerian Farmers. International Journal of Industrial Ergonomics, 29, 331–341.
32.Mehta, C.R., Gite, L.P., Pharade, S.C., Majumder, J., & Pandey, M.M. (2008). Review of anthropometric considerations for tractor seat design. International Journal of Industrial Ergonomics, 38, 546–554.
33.NSAI. (2011). SNI 0331-2011: Cangkul – Syarat mutu dan metode uji. Jakarta: National Standardization Agency of Indonesia.
34.NSAI. (1989a). SNI 02-1456-1989: Sabit bergerigi. Jakarta: National Standardization Agency of Indonesia.
35.NSAI. (1989b). SNI 05-0551-1989: Mutu dan cara uji parang. Jakarta: National Standardization Agency of Indonesia.
36.Nag, P.K., Goswami, A., Ashtekar, S.P., & Pradhan, C.K. (1988). Ergonomics in sickle operation. Applied Ergonomics, 19 (3), 233–239.
37.Obi, O.F., Ugwuishiwu, B.O., & Adeboye, B.S. (2015). A survey of anthropometry of rural agricultural workers in Enugu State, South-Eastern Nigeria, Ergonomics, 58(6), 1–13.
38.Openshaw, S., & Taylor, E. (2006). Ergonomics and Design a Reference Guide [Allsteel. Inc]. Retrieved from http://www.allsteeloffice.com/ergo.
39.Pheasant, S., & Haslegrave, C.M. (2006). Bodyspace: Antropometry, Ergonomics and the Design of Work. Boca Raton, Fl: CRC Press.
40.Pulat, B. M. (1997). Fundamentals of Industrial Ergonomics. Illinois: Waveland Press.
41.Patel, R., Kumar, A., & Mohan, D. (2000). Development of an ergonomic evaluation facility for Indian tractors, Applied Ergonomics, 31, 311-316.
42.Prado-Lu, J.L.D. (2007). Anthropometric measurement of Filipino manufacturing workers. International Journal of Industrial Ergonomics, 37, 497–503.
43.Rosyidi, C.N., Susmartini, S., Purwaningrum, L., & Muraki, S., (2014). Mismatch analysis of elementary school furniture in several regions of Central Java, Indonesia, and redesign recommendations. Applied Mechanics and Materials, 660, 1057–1061.
44.Rogan, A. (1992). Ergonomic constraints on crop production in the tropics. Overseas Divison Report OD/92/4, United Kingdom: Roben’s Institute of Health and Safety, Silsoe Research Institute.
45.Sanders, M.S., & McCormick, E.J. (1993). Human Factors in Engineering and Design. (7th ed.). New York: McGraw-Hill.
46.Sutalaksana, I.Z., & Widyanti, A. (2016). Anthropometry approach in workplace redesign in Indonesian Sundanese roof tile industries. International Journal of Industrial Ergonomics, 53, 299–305.
47.Syuaib, M. F. (2015). Anthropometric study of farm workers on Java Island, Indonesia, and its implications for the design of farm tools and equipment. Applied Ergonomics, 51, 222–235.
48.Shahida, M.S.N, Zawiah, M.D.S, & Case, K. (2015). The relationship between anthropometry and hand grip strength among elderly Malaysians, International Journal of Industrial Ergonomics, 50, 17–25.
49.Thariq, M.G.M., Munasinghe, H.P., & Abeysekara, J.D. (2010). Designing chairs with mounted desktop for university students: rrgonomics and comfort. International Journal of Industrial Ergonomics, 40 (1), 299–305.
50.Widyanti, A., Susanti, L., Sutalaksana, I.Z., & Muslim, K. (2015). Ethnic differences in Indonesian anthropometry data: evidence from three different largest ethnics. International Journal of Industrial Ergonomics, 47, 72–78.
51.Widyanti, A., Mahachandra, M., Soetisna, H.R., Sutalaksana, I.Z., & Muslim, K. (2017). Anthropometry of Indonesian Sundanese children and the development of clothing size system for Indonesian Sundanese children aged 6–10 year. International Journal of Industrial Ergonomics, 61, 37–46.
52.Wang, M.J., Wang, E.M.Y., & Lin, Y.C. (2002). The anthropometric database for children and young adults in Taiwan. Applied Ergonomics, 33, 583–585.
53.Wibowo, R.K.K., & Soni, P. (2014). Anthropometry and Agricultural Hand Tool Design for Javanese and Madurese Farmers in East Java, Indonesia. APCBEE Procedia, 8, 119–124.
54.Yanto, Lu, C.W., & Lu, J.M. (2017). Evaluation of the Indonesian national standard for elementary school furniture based on children''s anthropometry. Applied Ergonomics, 62, 168–181.
55.Yanto, Lu, C.W., Bachri, K.O. (2015). Anthropometric study of Indonesian university students in Jakarta. Proceedings of the International Conference on Industrial Engineering and Operation Management (IOEM) 2015, Dubai: IEEE.
56.Yanto, Lu, C.W., Lioenita, D.C. (2015). The study of anthropometry of Indonesian infant age 0-2 years in Jakarta. In Shih, Y.C.& Liang, S.F.M. (Ed). Bridging Research and Good Practices toward Patient Welfare: Healthcare Systems Ergonomics and Patient Safety 2014 (pp. 363–370). CRC Press, Taylor & Francis Group.
57.Vanderwal, L., Rautiainen, R., Kuye, R., Peek-Asa, C., Cook, T., Ramirez, M., Culp, K., & Donham, K. (2011). Evaluation of long and short handled hand hoes for land preparation, developed in a participatory manner among women vegetable farmers in the Gambia. Applied Ergonomics, 42, 749–756.
電子全文 電子全文(本篇電子全文限研究生所屬學校校內系統及IP範圍內開放)
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top