(18.210.28.227) 您好!臺灣時間:2019/11/23 10:25
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果

詳目顯示:::

我願授權國圖
本論文永久網址: 
line
研究生:劉光輝
研究生(外文):KUANG-HUI LIU
論文名稱:非破壞性探討安定化熱處理對Al-10Mg鍛造合金微結構、機械與腐蝕性質之影響
論文名稱(外文):Correlation between non-destructive test with mechanical properties and corrosion resistance of Al-10 Mg forged-alloy
指導教授:李勝隆李勝隆引用關係
指導教授(外文):Sheng-Long Lee
學位類別:碩士
校院名稱:國立中央大學
系所名稱:機械工程學系在職專班
學門:工程學門
學類:機械工程學類
論文出版年:2018
畢業學年度:107
語文別:中文
論文頁數:31
中文關鍵詞:鋁鎂合金安定化處理敏化現象非破壞性檢測導電度
相關次數:
  • 被引用被引用:0
  • 點閱點閱:17
  • 評分評分:系統版面圖檔系統版面圖檔系統版面圖檔系統版面圖檔系統版面圖檔
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:0
M5200合金係一高Mg含量的鍛造鋁合金,由520.0鑄造鋁合金(Al-10Mg)改良而成。本研究欲探討安定化熱處理是否具有改善材料性質之功能,並藉由非破壞性檢測技術(導電度量測),探討敏化試驗對M5200(Al-10Mg)鍛造合金機械性質與腐蝕抗性的影響。實驗結果顯示,M5200(Al-10Mg) 鍛造合金於285 ℃下進行1h的安定化熱處理,結構為回復(recovery)及極輕微的再結晶(recrystallization),使得材料不至於因為敏化,大量β相析出導致抗腐蝕能力的降低。而重量損失測試(依規範ASTM-G67)顯示,合金雖具有中度沿晶腐蝕敏感性之隱憂,但因M5200屬於鎂含量極高之合金,此G67試驗之結果仍在可以接受之範圍內,也證實可以利用且非破壞性檢測技術(導電度)來預測合金之硬度、與G67 重量損失,且其預估值之誤差率皆在10 %以內。
M5200 is a forging alloy that contains high magnesium content, which is modified from 520.0(Al-10Mg) casting alloy. In this study, we intended to investigate whether stabilizing treatment is capable to improve the material’s properties or not. We also utilized non-destructive testing technology (electrical conductivity), to discuss the influence of sensitization on M5200 alloy’s mechanical properties and corrosion resistance. The results suggested that under 285 ℃/1h stabilizing treatment, the microstructure of M5200 showed a recovery texture and minor recrystallization; hence, even the abundant β phase precipitate, the material’s corrosion resistance will not decay significantly. Although the ASTM G67 Standard Test indicated that M5200 has relatively severe intergranular corrosion, but for such alloy which contains high percentage of magnesium, the result of ASTM G67 Standard Test is still acceptable. Furthermore, non-destructive testing technology also prove the conductivity, hardness and G67 Standard Test have a certain extent of correlation ship. Through the linear regulation, the deviations between the Trend line and real data are smaller than 10 %.
總目錄
摘要 i
Abstract ii
誌謝 iii
圖目錄 v
表目錄 vi
一、 前言 1
1.1 合金簡介與研究背景 1
二、 實驗步驟 7
三、 結果與討論 9
3.1 鍛造性評估與安定化熱處理條件之決定 9
3.2 微結構觀察 12
3.3 敏化對M5200鋁鎂合金之非破壞性導電度值檢測之影響 15
3.4 耐蝕性質分析 17
3.5 機械性質測試 19
3.6 冷卻方式對M5200合金性質之影響 20
3.7 非破壞性檢測(導電度)與腐蝕,機械性質之關係 24
四、 結論 27
五、 參考文獻 29
[ASM] J.R.Davis & Associates,ASM Specialty Handbook Aluminum and Aluminum Alloys. (1994)
[ASTM1] ASTM B928/B928M-09 Standard Specification for High
Magnesium Aluminum-Alloy Sheet and Plate for Marine Service and Similar Environments. (2015)
[ASTM2] ASTM G67-04 Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid(NAMLT Test). (2013)
[ASTM3] ASTM B557M-07 Standard Test Methods for Tension Testing Wrought and Cast Aluminum and Magnesium-Alloy Products. (2007)
[AT] 退火溫度對AA5083-H15鋁鎂合金沿晶腐蝕與應力腐蝕性質之影響(2012)
[BOV] F.S. Bovard,“Corrosion in marine and saltwater environments II, in D.A. Shifler, T. Tsuru, P.M. Natishan, S. Ito (Eds.),”Electrochemical Society Proceedings, vol. 2004–14, pp. 232–243.(2005)
[DAV1]J. R. Davis and Associates, “ASM Specialty Handbook:Aluminum and Aluminum Alloys”, ASM International Materials Park, Ohio, pp. 582.(1994)
[DAV2]J. R. Davis and Associates, “ASM Specialty Handbook:Aluminum and Aluminum Alloys”, ASM International Materials Park, Ohio, pp. 61.(1994)
[DAV3]J. R. Davis and Associates, “ASM Specialty Handbook:Aluminum and Aluminum Alloys”, ASM International Materials Park, Ohio, pp. 33.(1994)
[DAV5] J. R. Davis and Associates, “ASM Specialty Handbook:
Aluminum and Aluminum Alloys”, ASM International Materials Park, Ohio, pp. 551.(1994)
[FAW] Fawad Tariq , Nausheen Naz , Rasheed Ahmed Baloch , Faisal ,”Characterization of Material Properties of 2xxx Series Al-Alloys by Non Destructive Testing Techniques”, Journal of Nondestructive Evaluation, Vol. 31, pp. 17-33. (2012)
[GOS] R. Goswamia, G. Spanosa, P. S. Paoa, R. L. Holtza,“Precipitation Behavior of the β Phase in Al-5083”,Materials Science and Engineering A, Vol. 527, pp. 1089-1095.(2010)
[GUR] C. H. Gür, I. Yıldız, “Non-Destructive Investigation on the Effect of Precipitation Hardening on Impact Toughness of 7020 Al-Zn-Mg alloy”, Materials Science and Engineering A, Vol. 382 , pp. 395-400.(2004)
[HAB] A Habibalahi, M S Safizadeh, “Pulsed Eddy Current and Ultrasonic Data Fusion Applied to Stress Measurement”, Measurement Science and Technology, Vol. 25, 055601.(2014)
[HAT] J.E. Hatch,“Aluminum: Properties and Physical Metallurgy,” ASM International Metals Park, Ohio, pp.356.(1984)
[HOL]R. L. Holtz, P. S. Pao, R. A. Bayles, T. M. Longazel, R. Goswami, “Corrosion-Fatigue Behavior of Aluminum Alloy 5083-H131 Sensitized at 448 K (175°C),” Metallurgical and Materials Transactions A, Vol. 43, pp. 2839-2849.(2012)
[LEE]S-L. Lee, C-H Yen, C-T Wu, Y-H Chen,“Effects of annealing temperature on stress corrosion susceptibility of AA5083-H15 alloy”, Journal of Materials Research, Volume 31(8), pp.1163-1170, April 28, (2016)
[OGU] I. N. A. Oguocha, O. J. Adigun, S. Yannacopoulos,“Effect of Sensitization Heat Treatment on Properties of Al-Mg Alloy AA5083-H116”, J Mater Sci ,Vol. 43, pp. 4208-4214.(2008)
[POP]Miljana Popovi, Endre Romhanji,“Characterization of Microstructural Changes in an Al-6.8 wt. % Mg Alloy by Electrical Resistivity Measurements”, Materials Science and Engineering A, Vol. 492, pp. 460-467.(2008)
[SEA] J.L. Searles, P.I. Gouma, R.G. Buchheit,“Stress Corrosion Cracking of Sensitized AA5083(Al-4.5Mg-1.0Mn),”METALLURGICAL AND MATERIALS TRANSACTIONS A, vol. 32, pp.2859–2867.(2001)
[STE] J. Stella, J. Cerezo, E. Rodriguez, ”Characterization of the Sensitization Degree in the AISI 304 Stainless Steel Using Spectral Analysis and Conventional Ultrasonic Techniques”, NDT&E International, Vol. 42, pp. 267-274.(2009)
[STM] Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)1 (2013)
[YUN] Yunze He, Guiyun Tian, Hong Zang, Mohammed Alamin, Anthony Simm, Paul Jackson, ”Steel Corrosion Characterization Using Pulsed Eddy Current Systems”, IEEE Sensors, Vol. 12, No. 6, pp. 2113-2120.(2012)
連結至畢業學校之論文網頁點我開啟連結
註: 此連結為研究生畢業學校所提供,不一定有電子全文可供下載,若連結有誤,請點選上方之〝勘誤回報〞功能,我們會盡快修正,謝謝!
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top
系統版面圖檔 系統版面圖檔