臺灣博碩士論文加值系統

　當機器人在工作空間內之運動路徑接近奇異點時會非常不穩定而造成控制上之問題。目前所使用判斷與奇異點接近程度之方法之計算過程在時間上可能不符合即時控制上之需求。本文首先提出簡化賈氏矩陣行列式值之方法以增加運算速度。計算行列式值時須先利用反位移分析求得各旋轉軸之角位移再代回賈氏矩陣才能判斷是否接近奇異點，本文另外提出一個能夠以反位移分析之二次多項式直接判斷與奇異點接近程度之方法，此方法不須使用到賈氏矩陣因此可大幅提高運算效率。以上兩種方法因牽涉到較複雜之理論而非一般現場工作人員所能瞭解，因此以螺旋理論為基礎提出一個可用目視法大概判斷機器人是否接近奇異點之方法。

　A manipulator becomes very unstable when its trajectory in task space approaches singular points. Current methods to detect singularity might not meet the time requirement in on-line control. This thesis first employs simplified link parameters to facilitate the computation process for the determinant of the Jacobian. The determinant of the Jacobian cannot be computed unless all joint variables are determined by solving the inverse kinematics. This work proposes a new method that direct employs the coefficients of quadratics used in inverse kinematics to detect singularity. The method is much more efficient because it can evaluate the closeness to singularity without using the Jacobian. The two proposed methods, however, might be too complicated for factory workers to implement, so a simple visual approach, developed from screw theory, is introduced to detect singularity.

中文摘要-----------------I
Abstract-----------------II
誌謝---------------------III
目錄---------------------IV
圖表目錄-----------------VI
第一章 緒論--------------1
1-1 研究動機-------------1
1-2 文獻回顧-------------2
1-3 論文架構-------------4
第二章 理論基礎----------5
2-1 座標系轉換-----------5
2-2 連桿參數定義---------6
2-3 Denavit-Hartenberg齊次轉換矩陣--------7
2-4 單位螺旋與賈氏矩陣---------------------8
第三章 賈氏矩陣法--------------------------14
3-1 行列式值與參考座標系之關係-------------14
3-2 工業用機器人---------------------------18
第四章 反位移分析--------------------------22
4-1 基本方程式-----------------------------23
4-2 五種類型之反位移分析-------------------24
4-3 判別式與奇異點之關係-------------------37
4-4 數值範例-------------------------------52
4-4-1 PUMA構型之反位移分析----------------52
4-4-2 兩判別式之比較----------------------61
第五章 螺旋理論法--------------------------65
5-1 α_2=0°奇異點位置---------------------65
5-2 a_2=0奇異點位置----------------------69
5-3 α_1=0°奇異點位置---------------------72
5-4 a_1=0奇異點位置----------------------75
第六章 研究結果與未來發展------------------81
參考文獻-----------------------------------83
作者簡介-----------------------------------86

[1]Piper, D.L and Roth, b.,”The kinematics of Manipulator Under Computer Control”, International congress for the Theory of Machines and Mechanisms, Vol. 2,pp. 159-168(1969)
[2]K. J. Waldron, S. L. Wang and S. JABolin, “A Study of the Jacobian Matrix of Serial Manipulators”, Journal of mechanisms, transmissions, and automation in design, Vol. 107, pp.230-237 (1985)
[3]Y. Nakamura and H. Hanafusa, “Inverse kinematic solutions with singularity robustness for robot manipulator control,” Trans. ASME J. Dynamic Syst. Meas. Contr., Vol. 108 ,pp.163–171, (1986)
[4]C. W. Wampler , “Manipulator inverse kinematic solutions based on vector formulations and damped least-squares methods,” IEEE Transactions on Systems, Man, and Cybernetics, Vol. ,pp.93–101(1986)
[5]Shih-Liang Wang and Kenneth J. Waldron, “A Study of the Singular Configurations of Serial Manipulators”, Journal of mechanisms, transmissions, and automation in design, Vol. 109, pp. 14-20 (1987)
[6]Shaheen Ahmad and Shengwu Luo “Analysis of Kinematic Singularities for Robot Manipulators In Cartesian Coordinate Parameters” Proceedings of IEEE International Conference on Robotics and Automation, Vol.2 , pp.840-845(1988)
[7]Chiaverini, S. and Egeland, O., “A solution to the singularity problem for six-joint manipulators”, Proceedings of IEEE International Conference on Robotics and Automation, vol. 1, pp.644 - 649 (1990)
[8]Kieffer, J. , “A view of singularities in manipulator inverse kinematics”, Advanced Robotics,Robots in Unstructured Environments, vol. 1, pp.668 - 671 (1991)
[9]Manja V. KirCanski, “Inverse kinematic problem near singularities for simple manipulators: Symbolical damped least-squares solution,” Proceedings of IEEE International Conference on Robotics and Automation, Vol. 1, pp.974–979(1993)
[10]Yu-Che Chen and C.L. Philip Chen , “An Analysis to the Singularity of Serial Manipulators Using the Theory of Reciprocal Screw”, Systems, Man, and Cybernetics, 'Humans, Information and Technology'., IEEE International Conference, vol. 1, pp.148 – 153(1994)
[11]F.T. Cheng, T.L. Hour, Y.Y. Sun, and T.H. Chen, “Study and Resolution of Singularities for a 6-DOF PUMA Manipulator”, IEEE Transactions on Systems, Man, and Cybernetics—Part B: Cybernetics, Vol. 27, No. 2,
pp.332-343(1997)
[12]Doik Kim, Wankyum Chung and Youngil Youm,“Singularity Analysis of 6-DOF Manipulators with the Analytical Representation of the Determinant”, Proceedings of IEEE International Conference on Robotics and Automation, Vol. 2, pp.889 -894(1999)
[13]K. Y. Tsai, D. Kohli and I. P. Hsu, “Admissible motion of special manipulators”, IEEE Transactions on Robotics and Automation, 10 (3) ,pp.386-391 (1994)
[14]University of Alaska Fairbanks ,
http://www.alaska.edu/uaf/cem/ece/remote-robotics/remoteHIL.xml
[15]RobotWorx, http://www.robots.com/comau.php?robot=nh4
[16]Animitsa A.V Analisis dinamiks property industrial robot,
http://masters.donntu.edu.ua/2007/kita/animitsa/diss/indexe.htm