跳到主要內容

臺灣博碩士論文加值系統

(18.97.14.86) 您好!臺灣時間:2025/02/12 11:10
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:郭韋志
研究生(外文):Wei-Zhi Guo
論文名稱:振動頻率對不鏽鋼振動輔助車削品質影響之研究
論文名稱(外文):Study of the Effect of Vibration Frequencies on the Quality of Vibration Assisted Turning for Stainless Steel
指導教授:吳忠恕吳忠恕引用關係
學位類別:碩士
校院名稱:國立臺灣海洋大學
系所名稱:機械與輪機工程學系
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2004
畢業學年度:92
語文別:英文
論文頁數:67
中文關鍵詞:振動車削不鏽鋼
外文關鍵詞:VibrationTurningStainless Steel
相關次數:
  • 被引用被引用:4
  • 點閱點閱:518
  • 評分評分:
  • 下載下載:135
  • 收藏至我的研究室書目清單書目收藏:0
摘要
本研究主旨在應用振動輔助切削技術來從事304系列不鏽鋼車削加工。針對加工的型式設計製作振動切削機構並加入不同型式的振動來進行切削加工實驗,以探討振動輔助切削對車削加工品質的影響。實驗結果顯示,加入振動可改善工件的表面粗糙度和降低切削力。
Abstract
In this thesis, Vibration assisted turning has been applied to the stainless steel 304. A vibration assisted turning device was designed and different types of vibration were used to examine the effect of vibration assisted turning on machining quality. Experiment results showed that vibration assisted turning improves the surface roughness of workpiece and decreases the cutting force.
目錄
第一章 緒論.........................................................1
1.1 前言.........................................................1
1.2 文獻回顧.........................................................2
1.3 研究動機與目的.........................................................4
1.4 論文架構.........................................................5
第二章 實驗原理.........................................................6
2.1 傳統車削原理………………………………....………………….6
2.2 切屑的形狀及其形成………………………....………………….7
2.3 切削溫度………………………………………....……………….9
2.4 冷卻劑………………………………………...………………...12
2.5 振動切削加工之原理……………………...…………………...13
2.6 切削刀具材料介紹……………………...…………………...…15
2.7 刀具壽命………………………………...……………………...18
第三章 實驗設備與設計………………………………………….….21
3.1 實驗設備……………………………………...………………...21
3.2實驗設計…………………………………………….....…………28
3.2.1 反應曲面法………………………………....…………………28
3.2.2 直交表…………………………………………....……………29
3.2.3 反應曲面法…………………………………..……………....31
3.2.4 實驗設計.....................................................….36
第四章 實驗結果與分析……………………………………………..42
4.1 實驗結果………………………………………...…………...…43
4.2 利用SAS統計軟體建立數學模式…………….....……………..46
4.3 實驗結果與分析………………………………...………….…..49
4.4 表面粗糙度之探討……………………………...…...…………61
第五章 結論與未來展望……………………………………….…….64
5.1 結論………………………………………………...……..…….64
5.2 未來展望………………………………………...……….……..64
Reference……………….……….………………………...………..65
References
[1] Y. C. Richard, Y. L. Steven, ” Chatter Stability of A Slender Cutting Tool in Turning with Tool Wear Effect,” Int. J. Mach. Tools Manufact., Vol. 38, No. 4, pp. 315-327, 1998.
[2] 賴哲雄、李明儒、江紀文、蔡青益,“車削動力模型的建立、驗證與動力分析”,機械月刊第二十三卷第三期,1997。
[3] V. K. Astashev, ” Effect of Ultrasonic Vibration of A Single-Point Tool on The Process of Cutting ,” Journal of Machinery Manufacture, No. 5, pp.65-70.
[4] A. I. Isaev, V. S. Anokhin, ” The Use of Ultrasonic Vibration of A Tool in The Course of Cutting Metals,” Vestnik Mashinostroeniya, No. 5, pp. 56-62, 1961.
[5] H. Weber, J. Herberger, R. Pilz, ”Turning of Machinable Glass Ceramics With An Ultrasonicaly Vibration Tool,” Annals of The CIRP, Vol. 33/1, pp. 85-87, 1984.
[6] L. J. Wang, J. Zhao, ”Influence on Surface Roughness in Turning With Ultrasonic Vibration Tool,” Mach. Tools Manufact., Vol. 27, No. 2, pp. 181-190, 1987.
[7] T. Moriwaki, E. Shamoto, ”Ultraprecision Diamond Turning of Stainless Steel by Applying Ultrasonic Vibration,” Annals of The CIRP, Vol40/1, pp. 559-562, 1992.
[8] G. F. Gao, B. Zhao, F. Jiao, C. S. Liu, ”Research on The Influence of The Cutting Conditions on The Surface Microstructure of Ultra-thin Wall Part in Ultrasonic Vibration Cutting,” Journal of Materials Processing Technology, Vol.129, pp. 66-70, 2002.
[9] 張萬欽、陳政雄,”超音波振動輔助切削之發展趨勢與發展 “,機械月刊第二十七卷第八期,2001。
[10] 簡國榆、張萬欽、陳政雄,”超音波振動輔助車削之動態幾何參數電腦模擬分析”,機械月刊第二十八卷第九期,2002。
[11] 梁家明,”振動切削技術應用於車削鑽削之研究”,碩士論文,國立雲林科技大學,2002。
[12] 王繼正、余永平、陳欽雨、黃聖芳、鄭正德、劉見成,”機械製造”,台北,高立圖書有限公司,民國87年。
[13] 蔡佳甫,”高速切削研究與應用” ,碩士論文,國立台灣大學,1999。
[14] 謝章嘉,”超音波振動搪孔加工之研究”,碩士論文,國立台灣大學,pp.4,1986。
[15] 洪良德,切削刀具學,全華科技圖書股份有限公司,pp.29-40,民74。
[16] 林維欣、紀松水,切削理論,全華科技圖書股份有限公司,pp.230-250,民76。
[17] 黃增煇,”鋼材切削性質評估指標之研究” ,碩士論文,國立成功大學,2003。
[18] 傅光華,”切削刀具學”,台北,高立圖書有限公司,pp.165-167,民國71年。
[19] 劉應進,”精密陶瓷電解式線上削銳之研究”,碩士論文,國立台灣海洋大學,pp.29-34,2000。
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top