跳到主要內容

臺灣博碩士論文加值系統

(18.97.9.169) 您好!臺灣時間:2025/02/18 01:56
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

我願授權國圖
: 
twitterline
研究生:謝武倫
研究生(外文):Wu-Lun Hsieh
論文名稱:平板鰭片熱交換器三維數值模擬分析
論文名稱(外文):Three-dimensional Numerical Analysis of Plate-Fin Heat Exchangers
指導教授:林育才
學位類別:碩士
校院名稱:元智大學
系所名稱:機械工程學系
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2006
畢業學年度:94
語文別:中文
論文頁數:49
中文關鍵詞:平板鰭片數值模擬鰭片性能
外文關鍵詞:Plate fin Heat ExchangerNumerical simulationperformance
相關次數:
  • 被引用被引用:0
  • 點閱點閱:225
  • 評分評分:
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:1
本文研究藉由平板鰭片熱交換器實驗結果與電腦數值模擬鰭片表面溫度分佈及鰭片表面水滴凝結放熱的情況比對,以驗證軟體的正確性,並以此做為依據而改變不同的參數經由熱傳分析與比較鰭片表面溫度分佈,以及空氣的溫度分佈,得知各參數對於鰭片性能的影響,進而可作為設計者的參考。
在數值模擬當中,改變的參數分別是相對濕度、鰭片高度、鰭片寬度、鰭片間距、鰭片厚度、鰭片速度、鰭片基底溫度等對鰭片性能的影響,由模擬結果可知濕度越高、鰭片高度越低、鰭片寬度越窄、鰭片間距越窄、鰭片厚度越薄、鰭片速度越快、基底溫度越高等都會導致鰭片性能降低,其中又以改變鰭片厚度對於鰭片的性能影響最大。
This paper has investigated the performance of the plate-fin heat exchangers numerically. The validity of the used CFD software was confirmed first by comparing the obtained numerical results of the fin surface temperature distribution and the region of the condensation on the fin surface with the measured data by previous experiments. The results of this thesis can be used as a guildline of the designers of heat exchangers.
The parameters studied in the present work include the relative humidity of the inlet air, the height of the fin, the width of the fin, the space between the fins, the thickness of the fin, the velocity of the inlet air and the base temperature of the fin. From the simulation results, it has been observed that the corresponding fin performance becomes worse with higher relative humidity of the inlet air, lower height of the fin, smaller width of the fin, narrower space between the fins, thinner of the fin, faster velocity of the approaching air and highter base temperature of the fin. It is also found that the most influential parameter is the thickness of the fin.
中文摘要 I
英文摘要 II
誌謝 III
目錄 IV
表目錄 V
圖目錄 VI
符號說明IX
第一章 緒論 1
1.1 前言 1
1.2 文獻回顧 3
1.3 研究的目地 5
第二章 理論介紹 6
2.1 散熱鰭片之規格 6
2.2 基本假設 6
2.3 CFDRC簡介 7
2.4 基礎理論的介紹 8
2.5 數值理論 10
2.6 數值方法 12
2.6.1 有限體積法 12
2.6.2 格點測試 13
2.6.3 格點數的設定 13
2.6.4 收斂條件 14
第三章 結果與討論 15
3.1 實驗結果與軟體結果比對 16
3.2 相對濕度的影響 20
3.3 鰭片基底溫度的影響 24
3.4 鰭片和鰭片間的間距之影響 28
3.5 鰭片高度的影響 31
3.6 鰭片寬度的影響 35
3.7 鰭片厚度的影響 38
3.8 入口風速的影響 42
第四章 結論 46
參考文獻 49
1.Wu,G and Bong,T.Y.,”Overall Efficiency of a Straight Fin With Combined Heat and Mass Transfer,”ASHRAE Transactions,100,part 1,pp.367-374. December 1994.
2.陳信利與張錦裕, ”矩形鳍片鳍管式熱交換器之熱液動性能研究”,國立成功大學機械工程學系碩士論文,民國九十五年六月.
3.Yur-Tsai Lin, Kuei-Chang Hsu, ”Performance of Rectangular Fin in Wet Conditions: Visualization and Wet Fin Efficiency,”ASME of,123,pp.827- 836,October 2001.
4.Kazeminejad,H.,”Analysis of One-dimensional fin assembly Heat Transfer With Dehumidification ,”Int.J. of Heat and Mass Tramsfer ,38,pp.455-462., June 1995.
5.Salah El-Din, M. M. ,”Performance analysis of partially-wet fin assembly”, Applied Thermal Engineering, 18, pp.337-339.,January 1998.
6.S. Y. Liang, T. N. Wang and G. K. Nathan,“ Comparison of one-dimen- sional and two-dimensional models for wet-surface fin efficiency of a plate-fin-tube heat exchanger,”Applied Thermal Engineering,20,pp.941-962., September 2000.
7.Vijayaraghavan Srinivasan and Ramesh K. Shah,“ Fin efficiency of extend- ed surfaces in two-phase flow,”Int.J Heat and Fluid Flow,18,pp.419-429., August 1997.
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top