跳到主要內容

臺灣博碩士論文加值系統

(18.97.14.86) 您好!臺灣時間:2025/02/12 11:13
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:黃喻鴻
研究生(外文):Yu-hung Huang
論文名稱:運用於電源供應器中之多點熱源散熱片最佳化設計
論文名稱(外文):Heat sink Optimization of Multi-Heat Source for Power Supply Units
指導教授:徐 業 良
指導教授(外文):Yeh-Liang Hsu
學位類別:碩士
校院名稱:元智大學
系所名稱:機械工程學系
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2006
畢業學年度:94
語文別:中文
論文頁數:48
中文關鍵詞:多點熱源最佳化設計散熱片
外文關鍵詞:heatsinkmulti-heat sourceoptimization
相關次數:
  • 被引用被引用:18
  • 點閱點閱:711
  • 評分評分:
  • 下載下載:29
  • 收藏至我的研究室書目清單書目收藏:0
近年來拜資訊產業發達之賜,伺服器應用服務市場大幅成長,市場上幾乎每天都有新伺服器產品問世,而應用在伺服器上的電源供應器也趨向於高電源密度(High Power Density)設計,可靠性、穩定性及品質的要求極為重要。此外由於生產電源供應器的技術層次不高,進入障礙低,競爭激烈,成本上的控制也是重要的因素。
電源供應器中之熱源大多來至功率晶體,為了降低熱源的產生,將晶體鎖在散熱片上,利用強制對流方式將晶體所產生的熱量帶走,以風扇對空氣作功造成氣體分子的擾動,再以對流的方式於散熱片表面或邊界做能量交換,進而達到冷卻的效果。由「牛頓冷卻定律(Newton’s Law of Cooling)」之對流熱傳關係式 得知,當對流熱傳係數值或接觸面積越大,所能帶走的熱量就越多,所以目前的散熱片設計都趨向於加大散熱片面積,增大風扇的流量,來提高散熱效能。然而考慮到空間與成本的限制下,散熱片的設計就不只是加大面積或增大風量,而是要在空間和成本的限制下,達到最佳效能的散熱片設計。
本文將針對高瓦數電源供應器之功率晶體散熱片進行最佳化設計,以尋找最適當的尺寸去達成最佳的散熱效率。許多相關研究針對單一熱源在強制對流下的熱傳現象做散熱片最佳化的探討,本文的重點則在於研究多熱源時的散熱情況。本研究中,由散熱鰭片熱阻分析出發,探討單卅多顆晶體不同位置對散熱片的影響,並導出晶體熱源方程式,再以典型的最佳化過程來求得散熱片最佳的設計參數,最後透過對最佳解之靈敏度分析與參數分析,提出多熱源散熱片之設計準則,以為工程師設計時之參考。
Most of the heat source of power supply comes from the power device; in order to decrease the heat, power device should be attached on the heat sink. The cooled air can take away the heat which produced by the power device, after that, using a fan to pull air, continue to have energy exchange on the heat sink surface or boundary through the heat convection, thus the cool off effect can be achieved. The heat diffusion equation from” Newton’s Law of Cooling” shows that, when the heat transfer coefficient number or heat sink surface is bigger and larger, the more heat can be taken away. Therefore, increasing the area of the heat sink with higher fan speed is the current design trend to increase the performance of heat exchange. However, there are some limitation from space and cost, so the current design trend needs to take space and cost into consideration to have the best heat sink design.
書名頁 …………………………………………………………………… i
論文口試委員審定書 ………………………………………………… ii
授權書 ………………………………………………………………… iii
中文摘要 ……………………………………………………………… iv
英文摘要 ………………………………………………………………… v
誌謝 ……………………………………………………………………… vi
目錄 ……………………………………………………………………… vii
表目錄 ………………………………………………………………… viii
圖目錄 …………………………………………………………………… ix
第一章 研究背景與目的 ………………………………………………… 1
1.1 研究背景與目的 ……………………………………………………… 1
1.2 論文架構 ……………………………………………………………… 5
第二章 電源供應器之熱阻分析 ………………………………………… 6
2.1 電源供應器之基本熱傳分析…………………………………………… 6
2.2 散熱鰭片熱傳導之熱阻分析…………………………………………… 8
2.3 散熱鰭片熱對流之熱阻分析………………………………………… 11
2.4 熱源位置之影響 ……………………………………………………… 12
2.5 多點熱源散熱片……………………………………………………… 15
2.6 多熱源間之影響……………………………………………………… 16
第三章 多點熱源散熱片之最佳化設計………………………………… 21
3.1多點熱源散熱片之設計需求…………………………………… 20
3.2 設計變數與設計參數之定義………………………………………… 23
3.3 最佳化設計數學模型………………………………………………… 26
3.4 多點熱源散熱片之設計最佳值……………………………………… 29
第四章 靈敏度分析與參數分析………………………………………… 35
4.1 幾何尺寸之靈敏度分析……………………………………………… 35
4.2 多點熱源散熱片設計之參數分析…………………………………… 41
第五章 結論與未來展望 ……………………………………………… 44
5.1 結論…………………………………………………………………… 44
5.2 未來展望……………………………………………………………… 46
參考文獻 ………………………………………………………………… 47
簡歷 ……………………………………………………………………… 48
Ellison, G. N., Thermal Computations for Electronic Equipment, Robert E. Krieger Publishing Co., Malabar, Florida, 1989.
Holman, J. P., Heat transfer, 3rd edition, McGraw-Hill, 1997.
Incropera, D., Fundamentals of Heat and Mass Transfer, 4th edition, Wiley, 1996.
Culham, J. R., Khan, W. A., and Yovanovich, M. M., “The Influence of Material Properties and Spreading Resistance in the Thermal Design of Plate Fin Heat Sinks”, 35th National Heat Transfer Conference, 2001.
Karimpourian B. and Mahmoudi J. 2005. “Some important considerations in heat sink design” 6th. Int. Conf. on Thermal Mechanical and Multi-physics Simulation and Experiments in Micro-Electronics and Micro-System, EuroSimE.
Lee, S., “Calculating spreading resistance in heat sinks,” Electronics Cooling, Vol.4, No.1, pp. 30-33, January 1998.
Rosenthal, R.E., 1998. “GAMS User’s Guide” GAMS Development Corporation.
Simons, R.E., “Estimating Parallel Plate-Fin Heat Sink Pressure Drop,” Electronics Cooling, Vol. 9, No. 2, pp. 8-10, May 2003.
Muzychka, Y. S. and Yovanovich, M. M., “Modeling Friction Factors in Non-circular Ducts for Developing Laminar Flow,” in Proc. 2nd AIAA Theoretical Fluid Mech. Meeting, 1buquerque, NM, pp. 15-18, June 1998.
莊嘉琛、劉國祥,“電腦用高效能可撓性散熱片節能研究”,民92,經濟部能源局能源技術節約報導,第50期。
鄭憶湘,散熱片在強制對流下之最佳化設計與實驗,民91,國立清華大學工程系統與科學研究所碩士論文。
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top