本研究由硝酸鈷當做起始物，加入NaOH後製作CoOOH。將CoOOH與不同重量比例的SnO2混合經400℃鍛燒4小時後得到不同比例的產物，並以TPR、TG、XRD分析樣品性質，將合成的材料作為CO氣體感測器的感測材料。
由實驗結果得知材料的重量比Co3O4-SnO2 = 1:4時為佳，在室溫下對CO的靈敏度(S=ΔmV)為23，反應時間(response time)t90=60秒，tR=65秒。
加入一些貴重金屬後Pt、Au、Ag、Cu未能提高CO的靈敏度，而加入0.1%CNT時靈敏度上升為192 ，t90=120秒，tR=150秒，反應在3分鐘內完成。優點在於實驗時在室溫下就可偵測而文獻上都需加溫才能進行，濃度的量測範圍在100-1000ppm。

Cobalt oxide CoOOH was prepared from a Co(NO3)2 solution via a precipitation with NaOH and oxidation in air. A series Co3O4-SnO2 composite were prepared from different weight ratio by calcining at 400℃ for 4h. The prepared samples were characterized by Temperature Programmed Reduction (TPR), Thermal Gravimetric Analyzer (TG/DTA), and X-ray diffraction (XRD) techniques. We applied the samples as a sensing material of CO sensor.
From experimental results, we find that the sample Co3O4-SnO2 = 1:4 better than other composite. The sensitivity(S=ΔmV) of CO in room temperature(S=23) in this study, response time(t90) and recover time(tR) are 60 and 65 second(~1 min).
We add different metals(Pt、Au、Ag、Cu) in composite Co3O4-SnO2 = 1:4 but not improve the sensitivity. Finally, we add 0.1%CNT in composite improve the sensitivity up to 192, t90 and tR are 120 and 150 second(~2-3 min). The sensing range from 100-1000ppm in room temperature.

第一章 序 論
1-1 一氧化碳的介紹
1-2 感測器原理及氣體感測器
1-3 氣體感測器的種類
1-4 金屬氧化物半導體型CO氣體感測器的文獻回顧
1-5 鈷化合物的簡介
1-6 研究目標

第二章 實 驗
2-1 實驗藥品
2-2 樣品製備方法
2-2.1 製備樣品CoOOH
2-2.2 製作感測材料Co3O4-SnO2
2-2.3 製作Co3O4-SnO2混入金屬的材料
2-2.4 製作Co3O4-SnO2混合CNT的材料
2-3 樣品鑑定
2-3.1 程溫還原系統(Temperature-Programmed Reduction,TPR)
2-3.2 熱重分析儀(Thermal Gravimetric Analyzer,TG/DTA)
2-3.3 X光繞射儀(X-Ray Diffraction, XRD)
2-4 製作CO感測器
2-5 氣體感測器的測試

第三章 結果與討論
3-1 感測材料的定性分析
3-1.1感測材料的程溫還原(TPR)分析
3-1.2熱穩定性分析
3-1.3各成份的XRD圖譜
3-2 感測曲線
3-3 各種材料對CO濃1000ppm之反應結果
3-3.1 以不同比例的Co3O4-SnO2為感測材料的感測曲線
3-3.2 以Co3O4-SnO2(1:4)為材料，混入金屬及CNT的感測
3-3.3 對0.1%CNT/Co3O4-SnO2(1:4)不同濃度下的感測結果
3-3.4 CO感測訊號對溫度的變化
3-4 干擾性的測試
3-4.1 0.1%CNT/Co3O4-SnO2(1:4)為材料感測CH4、NO2、H2
3-4.2 CH4、NO2、H2感測訊號對溫度的變化
3-5 穩定度
3-6 反應機構之證明

第四章 結 論

第五章 參考文獻

1. 許木嶺、錢新南，一氧化碳中毒，國防醫學，第31卷第3期，2000，195-201.
2. 內政部消防署一氧化碳意外、火災死亡人數統計，www.consumers.org.tw/attachfile/20061124094415265.doc，內政部消防署.
3. 物質安全資料表，www.iosh.gov.tw/data/f11/msdsno.htm，勞工安全衛生研究所.
4. 林敬二，楊美惠，楊寶旺，廖德章，薛敬和，化學大辭典，二版，高立圖書有限公司.
5. 張明揚、林杰樑，當心冬天無形的殺手：一氧化碳中毒，www.greencross.org.tw/toxin/CO_intoxication.htm，綠十字健康網.
6. 曹永偉，感測器技術入門，全華科技圖書股份有限公司.
7. 陳一誠，劉旭禎，一氧化碳氣體感測技術，工業材料雜誌，第227期，2005，68-80.
8. 曾明漢，觸煤燃燒型氣體感測器，材料與社會，第68期，1992， 57-61.
9. K. D. Song, B. S. Joo, N. J. Choi, Y. S. Lee, S. M. Lee, J. S. Huh, D. D. Lee, A micro hot-wire sensors for gas sensing applications, Sens. Acuators B, 2004, 102, 1-6.
10. 楊明長，曾坤億，王瓊紫，一氧化碳感測器之原理與應用，化工技術，第八卷第二期，2000，158-167.

11. P. S. Cho, K.W. Kim, J.H. Lee, Improvement of dynamic gas sensing behavior of SnO2 acicular particles by microwave calcination, Sens. Acuators B, 2007, 123, 1034-1039.
12. N. Yamazoe, Toward innovations of gas sensor technology, Sens. Acuators B, 2005, 108, 2-14.
13. U.S. Choi, G. Sakai, K. Shimanoe, N. Yamazoe, Sensing properties of SnO2–Co3O4 composites to CO and H2, Sens. Acuators B, 2004, 98, 166-173.
14. U. S. Choi, G. Sakai, K. Shimanoe, N. Yamazoe, Sensing properties of Au-loaded SnO2–Co3O4 composites to CO and H2, Sens. Acuators B, 2005, 107, 397-401.
15. S. Abe, U. S. Choi, K. Shimanoe, N. Yamazoe, Sens. Acuators B, Influences of ball-milling time on gas-sensing properties of SnO2–Co3O4 composites, 2005, 107, 516-522.
16. C. Aifan, H. Xiaodong, T. Zhangfa, B. Shouli, L. Ruixian, L. C. Chiun, Preparation, characterization and gas-sensing properties of SnO2–In2O3 nanocomposite oxides, Sens. Acuators B, 2006, 115, 316-321.
17. A. M. Azad., M. Hammoud, Fine-tuning of ceramic-based chemical sensors via novel microstructural modification I: Low level CO sensing by tungsten oxide, WO3, Sens. Acuators B, 2006, 119, 384.
18. R. J. Wu, J. G. Wu, T. K. Tsai, C. T. Yeh, Use of cobalt oxide CoOOH in a carbon monoxide sensor operating at low temperatures, Sens. Acuators B, 2006, 102, 104-109.
19. Y. J. Chen, D. E. Wu, C. T. Yeh, Rev. Adv. Mater. Sci., Oxidation of carbon monoxide over nanoparticles of cobalt oxides, 2003, 5, 41-46.
20. 蔡東剛，氧氫氧化鈷的製備及在一氧化碳感測器上的應用，國立清華大學碩士論文.
21. J. W. Robinson, E. M. Skelly Frame, G. M. Frame II, Undergraduate Instrumental analysis sixth edition, MARCEL DEKKER New York.
22. 陳志遠，二氧化鈦-二氧化錫材料應用於臭氧感測之研究，靜宜大學碩士論文.
23. R. J. Wu, C. H. Hu, C. T. Yeh, P.G. Su, Nanogold on powdered cobalt oxide for carbon monoxide sensor, Sens. Acuators B, 2003, 96, 596-601
24. H. Yamaura, J. Tamaki, K. Moriya, N. Miura, N. Yamazoe, Highly selective CO sensor using indium oxide doubly promoted by cobalt oxide and gold, J. Electrochem. Soc., 1997, 144, 158-160.
25. A. V. Salker, N. J. Choi, J. H. Kwak, B. S. Joo, D. D. Lee, Thick films of In, Bi and Pd metal oxides impregnated in LaCoO3 perovskite as carbon monoxide sensor, Sens. Acuators B, 2005, 106, 461-467.
26. K. Oto, A. Shinobe, M. Manabe, H. Kakuuchi, Y. Yoshida, T. Nakahara, New semiconductor type gas sensor for air quality control in automobile cabin, Sens. Acuators B, 2001, 77, 525-528.
27. L. L. Li, W. Wlodarski, K. Galatsis, D. A. Powell, A study of CO sensors with oscillatory response, Sens. Acuators B, 2003, 96, 610-614.

28. L. L. Li, W. Wlodarski, D. B. Akolekar, S. K. Bhargava, Oscillatory response of Pt-based CO sensors, Sens. Acuators B, 2005, 108, 496-500.
29. E. Comini, L. Yubao, Y. Brando, G. Sberveglieri, Gas sensing properties of MoO3 nanorods to CO and CH3OH, Chemical Physics Letters, 2005, 407, 368-371.
30. H. Gong, J. Q. Hu, J. H. Wang, C. H. Ong and F. R. Zhu, Nano-crystalline Cu-doped ZnO thin film gas sensor for CO, Sens. Acuators B, 2006, 115, 247-251.
31. E. Comini, G. Faglia, G. Sberveglieri, D. Calestani, L. Zanotti, M. Zha, Tin oxide nanobelts electrical and sensing properties, Sens. Acuators B, 2005, 111-112, 2-6.
32. H. B. Faramarz, M. Keshmiri, M. Kakavand, T. Troczynski, A resistive gas sensor based on undoped p-type anatase, Sens. Acuators B, 2005, 110, 28-35.
33. A. M. Azad, Fine-tuning of ceramic-based chemical sensors via novel microstructural modification Part II: Low level CO sensing by molybdenum oxide, MoO3, Sens. Acuators B, 2006, 120, 25-34.
34. P. Song, H. Qin, X. Liu, S. Huang, R. Zhang, J. Hu, M. Jiang, Structure, electrical and CO-sensing properties of the La0.8Pb0.2Fe1−xCoxO3 system, Sens. Acuators B, 2006, 119, 415-418.
35. Y. K. Jun, H. S. Kim, J. H. Lee, S. H. Hong, CO sensing performance in micro-arc oxidized TiO2 films for air quality control, Sens. Acuators B, 2006, 120, 69-73.
36. A. M. Ruiz, A. Cornet, K. Shimanoe, J. R. Morante, N. Yamazoe, Effect of various metal additives on the gas sensing performances of TiO2 nanocrystals obtained from hydrothermal treatments, Sens. Actuators B, 2005, 108, 34-40.
37. N. S. Ramgir, Y. K. Hwang, S. H. Jhung, I. S. Mulla, Jong-San Chang, Effect of Pt concentration on the physicochemical properties and CO sensing activity of mesostructured SnO2, Sens. Actuators B, 2006, 114, 275-282.
38. L. L. Li, W. Wlodarski, S. Ippolito, Platinum resistive film CO sensor without selective layer, Sens. Actuators B, 2005, 111-112, 130-134.
39. H. Yamaura, K. Moriya, N. Miura, N. Yamazoe, Mechanism of sensitivity promotion in CO sensor using indium oxide and cobalt oxide, Sens. Actuators B, 2000, 65, 39-41.
40. V. Dixit, S.C.K. Misra, B.S. Sharma, Carbon monoxide sensitivity of vacuum deposited polyaniline semiconducting thin films, Sens. Actuators B, 2005, 104, 90-93.
41. A. Salehi, A highly sensitive self heated SnO2 carbon monoxide sensor, Sens. Actuators B, 2003, 96, 88-93.
42. Z. Yong, L. Junhua, L. Xin, Z. Changchun, The structure optimization of the carbon nanotube film cathode in the application of gas sensor, Sens. Actuators B, 2006, 128, 278-289.