跳到主要內容

臺灣博碩士論文加值系統

(18.97.14.81) 您好!臺灣時間:2025/02/19 02:49
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

我願授權國圖
: 
twitterline
研究生:江林鴻
研究生(外文):Lin-Hung Chiang
論文名稱:應用田口法於四行程引擎進排氣凸輪設計研究
論文名稱(外文):Applying Taguchi Method on Inlet and Exhaust Cams Design for a Four-stroke Engine
指導教授:范憶華
指導教授(外文):Yi-Hua Fan
學位類別:碩士
校院名稱:中原大學
系所名稱:機械工程研究所
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2009
畢業學年度:97
語文別:中文
論文頁數:66
中文關鍵詞:進排氣凸輪揚程田口法四行程引擎進氣效率
外文關鍵詞:Intake efficiencyfour-stroke engineTaguchi method
相關次數:
  • 被引用被引用:0
  • 點閱點閱:304
  • 評分評分:
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:1
本文主要研究目的為改善高轉速四行程引擎的進氣效率的改善,高轉速引擎因為轉速較高,進氣門開啟時間較短,在高轉速狀態下進氣效率會變差,因此影響進氣效率的進排氣凸輪成為重要的引擎性能參數。利用進排氣凸輪改變進氣閥開啟截面積的大小,讓引擎在高轉速運轉下進氣流量變大,改變進氣效率可以使四行程引擎的燃燒效率提高並減少燃燒不完全的廢氣排放量,使引擎達到高效率和低汙染,符合環保要求。本文的實驗方法,首先量測2009 出廠KYMCO之RACING150 機車的引擎馬力,經特性要因圖分析後,選擇進排氣凸輪為控制因子。接著,利用田口法L9 直交表進行實驗,每組實驗取50 組數據的平均,減少人為操作誤差及引擎熱機前後的差異最後,利用田口品質工程與實驗設計的方式,再以變異數分析探討不同進排氣凸輪變化對於引擎馬力的影響。
本文實驗所獲得進氣凸輪揚程高度為5.7mm、排氣凸輪揚程高度為5.4mm、進氣凸輪寬度不變、排氣凸輪寬度加大0.25mm 為最佳,所得的引擎馬力再高轉速下都優於原廠設定,由此可見改變進排氣凸輪對於引擎馬力提升是有幫助的,尤其是在高轉速時,改變進氣凸輪揚程對引擎馬力提升影響甚大。
The purpose of this study is to improve the intake efficiency of the high-speed four-stroke engine. High-speed engines have short time to open the intake valve. So the intake efficiency will deteriorate. Therefore, the Intake efficiency is the important factor affects the engine efficiency. The engine horsepower experiment is based on the KYMCO RACING150 available in the market. We choose the intake and exhaust cam lift for the control factor by analyzing the characteristics with engine’s Cause and Effect Diagram. We choose three classes and using the Taguchi's Orthogonal Arrays-L9 for experiment. We choose the average of fifty data for each experiment data. Thus we can reduce the man-made errors in the operation and the difference before and after the heat of the internal combustion engine. To discuss the influence of the cam lift on the horsepower of the engine with the Taguchi method and the Analysis of Variation.
By using the cam lift to control the cross section of the valve, we can have large inlet flow when the engine is in high-speed operation. We can improve the combustion efficiency of the four-stroke engine by changing the inlet flow efficiency,and decrease the incomplete combustion of emissions. Thus, the engine with high efficiency and low pollution will achieve the request of environmental protection. Experimental results show there is the maximum horsepower of the engine when the intake cam lift is 6mm, and the exhaust cam lift is 5.1mm. Whatever the motor’s speed changing, the resulting horsepower of the engine is better than the original set. So it can be seen to change the intake and exhaust cam lift is important to improve the engine horsepower, especially in the high-speed.
目錄
中文摘要………………………………………………………………Ⅰ
英文摘要………………………………………………………………Ⅱ
目錄……………………………………………………………………Ⅲ
表目錄…………………………………………………………………Ⅵ
圖目錄…………………………………………………………………Ⅷ
第一章 緒論
1-1 前言………………………………………………………1
1-2 研究動機與目的…………………………………………2
1-3 研究流程…………………………………………………3
1-4 文獻回顧…………………………………………………4
1-5 內容大綱…………………………………………………6
第二章 四行程引擎介紹
2-1 四行程引擎工作原理……………………………………7
2-1-1 進氣行程………………………………………………8
2-1-2 壓縮行程………………………………………………9
2-1-3 動力行程……………………………………………10
2-1-4 排氣行程……………………………………………11
2-2 氣門正時…………………………………………………13
2-3 凸輪介紹…………………………………………………14
2-4 凸輪揚程與引擎性能之關係……………………………15
2-5 空燃比重要性……………………………………………16
第三章 實驗法設計
3-1 常見的實驗方法介紹……………………………………17
3-1-1 試誤法………………………………………………17
3-1-2 最佳猜測途徑………………………………………17
3-1-3 「一次一因子」實驗法……………………………18
3-1-4 「全因子」實驗法…………………………………18
3-1-5 田口試直交表實驗法………………………………18
3-2 田口方法介紹……………………………………………19
3-2-1 田口方法之特點…………………………………19
3-2-2 望目特性損失函數…………………………………22
3-2-3 望小特性損失函數…………………………………23
3-2-4 望大特性損失函數…………………………………24
3-2-5 田口方法之品質特性………………………………25
3-3 田口方法之實驗步驟……………………………………28
3-4 變異數分析…………………………………………….31
第四章 引擎進排氣凸輪揚程最佳化設計
4-1 實驗設備…………………………………………………34
4-2 要因分析…………………………………………………36
4-3 實驗規劃…………………………………………………37
4-4 實驗數據…………………………………………………39
4-5 實驗數據分析……………………………………………44
4-6 實驗結果…………………………………………………52
第五章 結論與未來研究方向
5-1 結論………………………………………………………54
5-2 未來研究方向……………………………………………54
參考文獻



表目錄
表2.1 空燃比及燃燒特性表…………………………………………16
表3.1 田口直交表L9(3
參考文獻
[1] Yan.W.,Anna.S. and Mike.L.,“Idle Speed Control: An old problem in a new engine design”,Ford Motor Co.,San Diego,Calfornia ,June 1999.
[2]吳凱聲,「四行程火花點火引擎進氣系統調諧與容積效率關係之研究」,碩士論文,大葉大學機械工程研究所,1999。
[3] Lawence.m. and Huei.p,“Modeling and Control of Variable Valve Timing Engine”,American Control Conference,Chicago,Illnois ,June 2000.
[4]白國平,「四行程引擎進排氣閥門開關角度之決定」,碩士論文,大葉大學工業工程研究所,2003。
[5]吳碩傑,「應用田口方法於高速引擎參數之最佳化設計」,碩士論文,華梵大學工業管理學系,2004。
[6]彭昱睿,「應用田口法於恆溫冷凍系統之參數分析與設計」,碩士論文,中原大學機械工程研究所,2007。
[7] A.Othta and Y.Ishida,“Dynamic Inlet Pressure and Volumetric Efficiency of Four Cylinder Engine”,SAE Paper 82040,1982.
[8] Isao Matsumoto and Alira Ohata,“Variable Induction System to Improve Volumetric Efficiency at Low and/or Medium Engine Speeds”SEA Paper 860100,1986.
[9] R.J.person and D.E.Winterbone,“A Rapid Synthesis Technique for Intake Manifold Design”,International Journal of Vehicle Design,Vol.10,NO.6,1989.
[10] Liguang.L.,Yan.S.,Yunkai.W,Jianwu.T. and Min.X.,“Development of an Electrical Control VVT System for High Speed SI Engine”,IEEE National Natural Science Foundation,2001.
[11]陳建霖,「氣油引擎進氣壓力及點火角度對引擎性能影響之電腦模擬」,碩士論文,國立雲林科技大學機械工程研究所,2003。
[12] 光陽機車官方網站http://www.kymco.com.tw/
[13] dynojet 馬力測試機規格http://www.dynojet.com/motorcycle_dyno/200i_dyno/Default.aspx
[14] 李輝煌,「田口方法品質設計的原理與實務」,高立圖書有限公司。
[15] 鐘清章,「品質工程」,中華民國品質學會。
[16] 吳復強,「田口品質工程」,全威圖書股份有限公司。
[17] 李友錚,「田口是品質工程」,科建管理顧問股份有限公司。
[18] 李冠宗、呂有豐,「內燃機」,高立圖書有限公司。
電子全文 電子全文(本篇電子全文限研究生所屬學校校內系統及IP範圍內開放)
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top