跳到主要內容

臺灣博碩士論文加值系統

(3.238.135.174) 您好!臺灣時間:2021/08/05 06:36
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:郭維強
研究生(外文):Wei-chiang Kuo
論文名稱:雙級複金屬燈電子式安定器之研製
論文名稱(外文):Study and Implementation of a Two-stage Electronic Ballast for Metal Halide Lamps
指導教授:鄭銘揚鄭銘揚引用關係梁從主
指導教授(外文):Ming-Yang ChengTsorng-Juu Liang
學位類別:碩士
校院名稱:國立成功大學
系所名稱:電機工程學系專班
學門:工程學門
學類:電資工程學類
論文種類:學術論文
論文出版年:2009
畢業學年度:97
語文別:中文
論文頁數:62
中文關鍵詞:安定器複金屬燈雙級低頻方波定功率
外文關鍵詞:constant powerlow-frequency square-waveballastmetal-halide lamptwo-stage
相關次數:
  • 被引用被引用:1
  • 點閱點閱:253
  • 評分評分:
  • 下載下載:62
  • 收藏至我的研究室書目清單書目收藏:0
本論文提出一「雙級複金屬燈電子式安定器」,電路架構之前級為昇壓型轉換器與昇/降壓型轉換器所構成的單開關雙組輸出整合型轉換器;後級為半橋換流器以低頻方波驅動高強度氣體放電燈,避免燈管產生音頻共振。當昇/降壓型轉換器操作於不連續導通模式下,藉由偵測匯流排電壓與電感電流訊號的準位平移方法達成定功率控制。本論文分析雙級複金屬電子式安定器架構之特性、動作原理與設計流程。最後實作一可操作於90~264 Vrms之70 W複金屬燈電子式安定器以驗證理論之正確性。實驗結果顯示,當輸入電壓為90~264 Vrms¬時,燈管功率變化為± 4.22%,輸入電壓為110 Vrms時,功率因數為0.97,整體安定器最高效率為85.86%。
A “Two-stage electronic ballast for metal halide lamps” is proposed in this thesis. The front stage is a single-switch two-output integrated converter, which is a combination of boost converter and buck-boost converter. The post stage is half-bridge inverter, which is used to drive the metal halide lamp with a low-frequency square-wave current to avoid acoustic resonance. When buck-boost converter is operated in discontinuous conduction mode, the constant lamp power control can be achieved with the level-shift method by sensing dc-bus voltage and inductor current signals. The operating principles and design guidelines of the proposed topology are presented. Finally, a laboratory prototype of 70 W electronic ballast for MH lamp with 90~264 Vrms universal input voltage is implemented to verify the feasibility. The experimental results show the variation of lamp power is ± 4.22% under 90~264 Vrms universal input voltage. The power factor is 0.97 at 110 Vrms ¬AC input voltage and the maximum efficiency of the ballast is 85.86%.
摘要 I
Abstract II
誌謝 III
目錄 V
表目錄 VIII
圖目錄 IX
第一章 緒論 1
1-1 研究背景與目的 1
1-2 論文大綱 5
第二章 複金屬燈特性與電子式安定器 6
2-1 複金屬燈物理特性 6
2-1-1 弧光放電過程 6
2-1-2 金屬鹵化物反應過程 7
2-1-3 啟動高壓 8
2-2 音頻共振 9
2-3 傳統三級架構電子式安定器 11
2-3-1 功率因數修正電路 12
2-3-2 燈管功率控制電路 14
2-3-3 燈管驅動電路 22
第三章 雙級複金屬燈電子式安定器 25
3-1 雙級複金屬燈電子式安定器之動作原理 27
3-2 單開關雙組輸出整合型轉換器電路之分析 33
3-2-1 不連續導通模式下輸入電流之分析 33
3-2-2 不連續導通模式下定功率控制之分析 34
3-2-3 直流匯流排電壓變動之分析 35
3-2-4 電感Lpf與電感Lm臨界導通條件的推導分析 36
3-2-5 考慮功率開關截止延遲之影響 38
3-3 燈管驅動電路 42
第四章 雙級電子式安定器設計與實驗結果 44
4-1安定器電路規格 44
4-2 安定器電路參數設計 46
4-2-1 輸入電容Cin 46
4-2-2 最小之直流匯流排電壓Vbusmin 46
4-2-3 電感參數值設計Lpf與Lm 46
4-2-4 電感電流回授增益Ki與前饋電壓回授增益Kv設計 47
4-2-5 輸出電容C1與C2設計 47
4-3 安定器元件選用 48
4-3-1 直流匯流排電壓變動範圍 48
4-3-2 開關S1耐壓選用 48
4-3-3 二極體耐壓選用 48
4-4 硬體電路控制器介紹 49
4-5 實驗結果 52
第五章 結論與未來展望 58
5-1 結論 58
5-2 未來展望 59
參考文獻 60
[1]王啟川等,「能源科技研究開發白皮書」,經濟部能源局,民國九十六年。
[2]M. Sugiura, “Review of metal-halide discharge-lamp development 1980-1992,” IEE Proc. Science, Measurement and Technology, vol. 140, no. 6, pp. 443-449, Nov. 1993.
[3]蔡慶龍,「低功率複金屬燈周邊裝置」,工研院能資所研究報告,民國九十二年。
[4]「大樓辦公室商業空間照明」,飛利浦照明,1994~1995。
[5]E. Deng and S. Cuk, “Negative incremental impedance and stability of fluorescent lamps,” in Proc. IEEE APEC’97, Feb. 1997, vol. 2, pp. 1050-1056.
[6]R. Osorio, M. Ponce, and M. A. O. Centro, “Simplified thermal-electric dynamic model for HID lamps,” in Proc. IEEE PESC’04, 2004 , vol. 4, pp. 2713-2718.
[7]馮鑰文,「複金屬燈之音頻共振現象探討」,國立中山大學電機工程學系碩士論文,民國九十四年五月。
[8]宋明俊,「複金屬燈特性研究」,國立中山大學電機工程學系碩士論文,民國八十九年六月。
[9]翁駿德,「博物館節能改善規劃與照明光源適用性探討」,科技博物,民國九十七年九月。
[10]復旦大學電光源實驗室,「電光源原理」,上海人民出版社,1976。
[11]W. Yan, Y. K. E. Ho, and S. Y. R. Hui, “Stability study and control methods for small-wattagehigh-intensity-discharge (HID) lamps,” IEEE Trans. on Industry Applications, vol. 37, no. 5, pp. 1522-1530, Sept-Oct. 2001.
[12]R. L. Lin and Z. Q. Wang, “2.65-MHz Self-Oscillating Electronic Ballast With Constant-Lamp-Current Control for Metal Halide Lamp,” IEEE Trans. on Power Electronics, vol. 22, no. 3, pp. 839-844, May 2007.
[13]C. A. Cheng, T. J. Liang, C. M. Chuang, and J. F. Chen, “A high power factor electronic ballast of projector lamps with variable frequency control,” in Proc. IEEE PESC’02, June 2002, vol. 1, pp. 23-27.
[14]D. J. Oh, K. M. Cho, and H. J. Kim, “Development of a digital controller using a novel complex modulation method for the metal halide lamp ballast,” IEEE Trans. on Power Electronics, vo1. 18, no. 1, pp. 390-400, Jan. 2003.
[15]J. Q. Wang, D. G. Xu, and H. Yang, “Low-frequency sine wave modulation of 250 W high-frequency metal halide lamp ballasts,” in Proc. IEEE APEC’04, 2004, vol. 2, pp. 1001-1007.
[16]C. S. Moo, C. K. Huang, and C. Y. Yang, “Acoustic-Resonance-Free High-Frequency Electronic Ballast for Metal Halide Lamps,” IEEE Trans. on Industrial Electronics, vol. 55, no. 10, pp. 3653-3660. Oct. 2008.
[17]J. M. Alonso, J. Ribas, M. R. Secades, J. Garcia, J. Cardesin, and M. A. D. Costa, “Evaluation of high-frequency sinusoidal waveform superposed with third harmonic for stable operation of metal halide lamps,” IEEE Trans. on Industry Applications, vol. 41, no. 3, May-June. 2005.
[18]H. Li, M. Shen, Y. Jiang, and Z. Qian, “A novel low-frequency electronic ballast for HID lamps,” IEEE Trans. on Industry Applications, vol. 41, no. 5, pp. 1401-1408, Sept-Oct. 2005.
[19]M. Ponce, A. Lopez, J. Correa, J. Arau, and J. M. Alonso, “Electronic ballast for HID lamps with high frequency square waveform to avoid acoustic resonances,” in Proc. IEEE APEC’01, March. 2001, vol. 2, pp. 658-663.
[20]S. T. Chen and L. L. Lee, “Optimized design of the electronic ballast for metal halide lamps,” in Proc. IEEE APEC’04, 2004, vol. 2, pp. 991-996.
[21]R. L. Lee and J. Y. Huang, “Stability Analysis of the Three-Stage Electronic Ballast for Metal Halide Lamp,” in Proc. IEEE PESC’06, June. 2006, pp. 1-7.
[22]D. van Casteren, M Hendrix and, J. L. Duarte, “Observer based ceramic HID lamp control,” in Proc. IEEE IAS’08, Oct. 2008, pp. 1-8.
[23]蕭建忠,「複金屬燈電子式安定器」,國立中央大學光電科學研究所碩士論文,民國九十四年。
[24]International Electromechanical Commission IEC 61000-3-2 Class-C standards: Electromagnetic compatibility (EMC) part 3-2: limits for harmonic current emissions. 2005.
[25]Y. D. Lee and R. L. Lin, “Constant power control based self-oscillating electronic ballast,” in Proc. IEEE APEC’05, March. 2005, vol. 1, pp. 589-595.
[26]J. Xu, M. Chen, T. Zhang, and Z. Qian, “A constant power control strategy of electronic ballast for HID lamp,” in Proc. IEEE IAS’06,Oct. 2006, vol. 3, pp. 1099-1102.
[27]C. A. Cheng, K. J. Lin, and K. L. Chu, “An electronic ballast with digitally constant power control for supplying automotive HID lamps,” in Proc. IEEE ICSET’08, Nov. 2008, pp. 1047-1052.
[28]S. Fongrut and I. Boonyaroonate, “Constant power control for high power factor electronic ballast high power metal halide lamp,” in Proc. IEEE ECTL’08, May. 2008, vol. 2, pp. 981-984.
[29]Y. Jiang, J. Zhou, and Z. Qian, “A novel single stage single switch PFC converter with constant power control for ballast for medium HID lamps,” in Proc. IEEE IAS’00, Oct. 2000, vol. 5, pp. 3415-3418.
[30]Z. Weiqiang and X. Dianguo, “Novel constant power control of electronic ballast for HPS lamps,” in Proc. IEEE ICIT’02, Dec. 2002, vol. 1, pp. 129-132.
[31]C. M. Huang, T. J. Liang, R. L. Lin, and J. F. Chen, “A novel constant power control circuit for HID electronic ballast,” IEEE Trans. on Power Electronics, vol. 22, no. 3, pp. 854-862, May. 2007.
[32]D. S. L. Simonetti, J. L. F. Viera, and G. C. D. Sousa, “Modeling of the high-power-factor discontinuous boost rectifiers,” IEEE Trans. on Industrial Electronics, vol. 46, no. 4, Aug. 1999.
[33]UC3844 Datasheet, Texas Instrument, 1999.
[34]IR2153 Datasheet, International Rectifier, 2005.
連結至畢業學校之論文網頁點我開啟連結
註: 此連結為研究生畢業學校所提供,不一定有電子全文可供下載,若連結有誤,請點選上方之〝勘誤回報〞功能,我們會盡快修正,謝謝!
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top