臺灣博碩士論文加值系統

本研究結合有限元素模擬軟體與沖模設計理論，探討光碟機固定用彈片之沖壓製程分析與模具設計。在沖剪成形分析上，主要探討模具間隙與壓料壓力對沖剪斷面之影響；在彎曲成形分析上，則是探討模具間隙、壓料壓力以及沖彎速度對於板材成形性之影響，分別透過有限元素分析軟體對沖剪與彎曲行為進行分析，並驗證CAE模擬板材成形之正確性。利用沖模設計理論探討如何設計一套光碟機固定用彈片之沖彎連續模具，首先從產品預評分析、產品加工性分析、板料展開樣式、料條佈置與排列、製程參數計算、模具總體設計、模具零件設計等開發流程，建構出適用於板材沖彎開發與設計系統。
本研究透過板材試驗建構出SUS304板材完整的資料庫。經由研究結果顯示，在板材沖剪方面，當模具間隙越小時，模輥面與撕裂面尺寸值越小，而剪切面尺寸則會越大；當壓料壓力越大時，模輥面與撕裂面尺寸值越小，而剪切面尺寸則會越大。在板材彎曲方面，影響尺寸精度及回彈量之主要參數為模具間隙與壓料壓力；影響板材應變之主要參數為模具間隙與沖彎速度。在模具設計方面，在料條佈置設計上，必須注意到每個道次之間的關聯性與連續性，考慮到帶料、拉料、力量平衡、回彈等問題，以有效地完成3D實體料帶佈置與排列，而在模具總體設計方面，建構出沖模行程、浮料高度、沖頭高度和脫料板行程等資訊，建立出一個實體模具。
將沖彎連續模具進行模具加工與組裝，藉由實際沖彎測試來驗證模擬與設計之可行性，並檢測光碟機固定用彈片之尺寸精度、回彈量以及沖剪斷面情形，經由實驗數據與模擬分析之數據互相比對後，其分析結果顯示 模擬與實際相符合，更加驗證有限元素分析軟體應用於板材沖剪與彎曲成形之可行性與可靠性。
在有限元素模擬軟體及沖模設計軟體的雙管齊下中，不但可以節省模具開發時程和成本，更可以提高成品的尺寸精度，就目前工業的發展來看，對於產品已經有微小化的趨勢，欲達到此目的，利用科學方法，有助於提升模具品質和產品精度。透過本文對於板材沖彎之開發與研究，有助於提供學術界與產業界之參考。

In this current study, finite element method (FEM) software and stamping die design theories were employed to investigate the stamping processes and die design of the immoveable spring chip in CD-ROM.
The shearing and the bending were analyzed by finite element method software and then the accuracy of sheets forming simulated through CAE was tested. In the shearing analysis, focuses were mainly on the effects of clearance and pressure on the shearing surface quality, while in the bending analysis, the effects of die clearance, strip hold pressure, and shearing-bending velocity on sheets forming was explored.
In addition, stamping die design theories were employed to investigate the die design system of sheets metal punching-bending for the immoveable spring chip in CD-ROM. Through the development processes, such as products assessment, stamping analysis, blank development, strip layout, process parameters calculation, die overall designs, and part design of dies, the development and design system for sheets metal punching-bending was constructed.
In this study, a complete database for the SUS304 sheets metal detail properties was also constructed through the tensile test. Results of the study showed that the size values of the rollover plane and the fracture plane decrease as the die clearance decreases, but the burnish plane increases as the die clearance decreases. However, when the strip hold pressure increases, the size values of rollover plane and the fracture plane decrease accordingly, and the size of burnish plane increases as the strip hold pressure increases.
In the aspect of bending analysis, the major parameters affecting the dimensions accuracy and the springback were the die clearance and strip hold pressure, while the die clearance and shearing-bending velocity were the main parameters which influenced the sheets metal strain.
In the design of the strip, attention should be paid to the relations and continuity between the strip designs, such as strip design, strip feeding, force balance, and springback. Then, the overall solid progressive die was constructed after the press stroke, blank lifting height, punch length and stripper travel distances had been determined.
The feasibility of the simulation and the dies deign was confirmed by dies manufacturing, erection and experiment. Furthermore, dimensions accuracy, springback and shearing-bending section of the immoveable spring chip in CD-ROM were examined. The results showed that the numerical values agree with the simulation ones with a reasonable accuracy, which further confirmed the feasibility and reliability of the application of FEM software for the sheets metal shearing-bending process.
Harnessing both FEM and stamping die design software has been proved not only to save the time for, and the cost of, the die development, but also to raise the quality and precision of the products. When the current trend of industrial development is product miniaturization, the exploitation of scientific methods surely will be the core to the satisfaction of the purpose.
The results found in the current study will shed some lights on the research and development of sheets metal shearing-bending process for the academia and industry.

中文摘要.....................................i
ABSTRACT.....................................iii
致謝.........................................v
目錄.........................................vi
表目錄.......................................x
圖目錄.......................................xii
符號說明.....................................xvii
第一章 緒論..................................1
1.1前言......................................1
1.2研究動機與目的............................3
1.3研究方法與步驟............................4
1.4文獻回顧..................................7
1.5論文總覽..................................13
第二章 薄板沖彎與模具設計原理................14
2.1板金成形理論..............................14
2.1.1基本塑性力學............................15
2.1.2材料之降伏準則..........................16
2.1.3材料之延性破裂準則......................19
2.2薄板沖剪原理..............................21
2.2.1板材之沖剪負荷..........................24
2.2.2模具間隙................................25
2.3薄板彎曲原理..............................27
2.3.1板材之彎曲壓力..........................31
2.3.2回彈現象................................32
2.4連續模具設計原理..........................35
2.4.1連續模具之採用與設計原則................38
2.4.2連續模具之基本形式......................41
第三章 研究方法..............................44
3.1薄板機械性質拉伸試驗......................44
3.1.1實驗原理................................44
3.1.2 實驗步驟...............................47
3.2 沖剪製程模擬.............................54
3.2.1 DEFORM軟體之簡介.......................54
3.2.2 沖剪製程模擬規劃.......................57
3.3 彎曲製程模擬.............................59
3.3.1 PAM-STAMP之簡介........................59
3.3.2 彎曲製程模擬規劃.......................61
3.4 製程參數最佳化...........................64
3.4.1 田口原理...............................64
3.4.2 田口方法...............................66
3.5模具設計..................................67
3.5.1 VISI之簡介.............................67
3.5.2 沖彎連續模具設計方法...................68
3.6模具製作與沖彎實驗........................69
3.6.1 模具製作...............................69
3.6.2沖彎實驗................................70
3.6.3沖彎件檢測..............................71
第四章 結果與討論............................73
4.1薄板機械性質分析..........................73
4.2 沖剪成形分析.............................78
4.2.1板材成形剪斷面之分析....................78
4.2.2板材成形應力應變之分析..................85
4.3 彎曲成形分析.............................89
4.3.1板材尺寸精度之分析......................89
4.3.2板材回彈量之分析........................101
4.3.3板材應變之分析..........................113
4.4 模具設計.................................123
4.4.1沖彎件分析..............................123
4.4.2板料展開與料條佈置......................124
4.4.3模具總體設計............................131
4.4.4模具零件設計............................139
4.4.5沖彎測試實驗............................141
4.4.6結果比對與分析..........................146
第五章 結論與建議............................149
5.1結論......................................149
5.2建議......................................152
參考文獻.....................................153
附錄.........................................156

[1]S.P. Keeler and W.A. Backofen, Plastic instability and fracture in sheets stretched over rigid punches, Trans ASM Vol. 56 (1963) 25.
[2]G.M. Goodwin, Application of strain analysis to sheet metal forming problems in the press shop, SAE paper NO.680093 (1968).
[3]K. Nakazima,T. Kikuma and K. Hasuka, Study on the Formability of SteelSheets, Yawata Technical Report, No.264, pp.141-154(1963).
[4]S.S. Hecker, Simple Technique for Determining Forming Limit Curve, SMI, PP.671-676 (1976).
[5]Heung Nam Han, Keun-Hwan Kim, A ductile fracture criterion in sheet metal forming process, Journal of Materials Processing Technology, 142, (2003) 231–238.
[6]許源泉，塑性加工學，全華科技圖書股份有限公司，2004年。
[7]A. M. Freudenthal, The Inelastic Behaviour of Engineering Materials and Structure, John Wiley, 1950.
[8]Hyunkee kim, Masahito Yamanaka, Prediction and elimination of ductile fracture in cold forging using FEM simulations, Trans. NAMRI/SME, 23, (1995) 63–69.
[9]E. Taupin, J. Breitling, W.T. Wu, T. Altan, Material fracture and burr formation in blanking results of FEM simulations and comparison with experiments, Journal of Materials Processing Technology, 59, (1996) 68-78.
[10]Gang Fang, Pan Zeng, Lulian Lou,Finite element simulation of the effect of clearance on the forming quality in the blanking process,Journal of Materials Processing Technology, 122, (2002) 249-254.
[11]余俊德，附V型壓環之精密剪斷有限元素分析，國立交通大學機械工程研究所碩士論文，2002年。
[12]Nobuo Hatanaka, Katsuhiko Yamaguchi, Norio Takakura, Takasi Iisuka, Simulation of sheared edge formation process in blanking of sheet metals, Journal of Materials Technology, 140, (2003)628-634.
[13]郭士銘，微型衝剪加工條件對剪斷面品質之影響，國立高雄應用科技大學模具工程系碩士班碩士論文，2006年。
[14]林明宏，微衝剪之成形模擬與剪斷面品質之研究，模具技術與論文發表會論文集，pp.73-79，2007年。
[15]M. Samuel, Experimental and numerical prediction of springback and side wall curl in U-bendings of anisotropic sheet metals, Journal of Materials Processing Technology, 105, (2000) 382-393.
[16]鍾崑來，應用田口式方法於鋼板彎曲成形最佳參數選擇之研究，國立成功大學造船及船舶機械工程研究所碩士論文，2002年。
[17]C.Q. Du, Springback control with variable binder force experiments and FEA simulation, AIP Conference proceedings, 712, (2004) 970-976.
[18]W.M. Chan, H.I. Chew, H.P. Lee, B.T. Cheok, Finite element analysis of spring-back of V-bending sheet metal forming processes, Journal of Materials Processing Technology, 148, (2004) 15-24.
[19]柯盛夫，板件彎曲成形回彈機制之研究，台灣大學機械工程研究所碩士論文，2004年。
[20]Dongye Fei , Peter Hodgson, Experimental and numerical studies of springback in air v-bending process for cold rolled TRIP steels, Nuclear Engineering and Design, 236, (2006) 1847–1851.
[21]S.K. Panthi, N. Ramakrishnan, K.K. Pathak, J.S. Chouhan, An analysis of springback in sheet metal bending using finite element method (FEM),Journal of Materials Processing Technology, 186, (2007) 120–124.
[22]蘇昱竹，先進高強度鋼板沖壓成形回彈現象之研究，台灣大學工學院機
械工程學系碩士論文，2007年。
[23]Daw-Kwei Leu, Chung-Ming Hsieh, The influence of coining force on spring-back reduction in V-die bending process, Journal of Materials Processing Technology, 196, (2008)230~235.
[24]鄧慶華，剪斷彎曲連續沖模加工站之規劃與料條排列最佳化分析，台灣科技大學機械工程技術研究所碩士論文，1998年。
[25]邱先拿，沖壓模具設計手冊，金屬工業研究發展中心，2000年。
[26]Keun Park, Sang-Ryun Choi, Finite element analysis for the lamination process of a precision motor core using progressive stacking dies, Journal of Materials Processing Technology, 130-131, (2002) 477-481.
[27]山口文雄，連續沖壓模具設計之基礎與應用，全華科技圖書股份有限公司，2003年。
[28]Sung-Bo Sim, Sung-Taeg Lee, Chan-Ho Jang, A study on the development of center carrier type progressive die for U-bending part process, Journal of Materials Processing Technology, 153–154, (2004) 1005–1010.
[29]陳永濱、陳炳明審校，沖壓模具設計基礎，金禾資訊，2005年。
[30]李輝煌，田口方法-品質設計的原理與實務，高立圖書有限公司，2008年。
[31]巫益賢，微小齒輪的精微沖壓連續模具設計與製作之研究，高雄應用科技大學模具工程碩士班碩士論文，2006年。
[32]蘇貴福，薄板之沖床加工，全華科技圖書股份有限公司，1993年。
[33]鄭朝友，應用田口法改善成形模具之應力，高雄應用科技大學模具工程系碩士論文，2007年。