跳到主要內容

臺灣博碩士論文加值系統

(34.204.180.223) 您好!臺灣時間:2021/08/05 15:13
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:李世鈞
研究生(外文):Shih-Jyun Li
論文名稱:雙頻帶通濾波器
論文名稱(外文):Design Of Dual-Band Bandpass Filter
指導教授:湯敬文
指導教授(外文):Ching-Wen Tang
口試委員:林祐生黃尊禧吳建華
口試委員(外文):Lin Yo-ShenHuang Tzuen-HsiWu Janne-Wha
口試日期:2012-07-10
學位類別:碩士
校院名稱:國立中正大學
系所名稱:電機工程研究所
學門:工程學門
學類:電資工程學類
論文種類:學術論文
論文出版年:2012
畢業學年度:100
語文別:中文
論文頁數:92
中文關鍵詞:雙頻帶通濾波器單頻帶通濾波器微帶線指叉式電容補償
外文關鍵詞:dual band bandpass filtersingle band bandpass filtermicrostrip lineinterdigital capacitance compensation
相關次數:
  • 被引用被引用:0
  • 點閱點閱:298
  • 評分評分:
  • 下載下載:30
  • 收藏至我的研究室書目清單書目收藏:0
本論文分兩個部分,第一部分為第三章的頻寬與頻帶可調控之雙頻帶通濾波器,透過數學公式的分析與驗證,設計出一套可以調控頻帶與頻寬的完整設計流程,並利用指叉式電容補償的方法來解決平行耦合線在微帶線實作上奇偶模向數不一的問題。此濾波器的特點是傳輸零點直接出現在頻帶的兩旁以及截止帶上,因此能達成良好的濾波特性。
接著在第四章提出頻帶可調控之雙頻帶通濾波器,同樣是雙頻帶通濾波器,不過電路架構和第三章不同。它是由兩個單頻帶通濾波器組合而成一雙頻帶通濾波器,特點是兩個通帶的頻率位置可以分開調控,透過大量的模擬數據整理出圖表來方便設計,最後也是以微帶線的方式來實作。
上述電路均使用全波電磁模擬軟體進行模擬工作,並實際進行電路製作與量測。經由量測結果與電磁模擬相比較,確實驗證與理論有良好的一致性。

This paper is divided in two parts, the first part introduce a dual band bandpass filter in chapter 3. By mathematical analysis and verification to complete a designing procedure, and using interdigital capacitance compensation to solve the phase difference between the even mode and odd mode of coupled lines. The advantage of this filter is the transmission zeros is right on the edge of passbands and the center of stopbands ccausing good filter effect.
In chapter 4 also introduce a dual band bandpass filter,but with different structure to chapter 3. It is a dual band bandpass filter combined with two single band bandpass filter,the advantage of this filter is it can adjust the position of passband respectively.
The circuits is designed with electromagnetic simulation software, and carry out to microstrip line,it have well consistency between theory and measurements results.

第一章 緒論.............. ...................................................................................................1
1.1 研究動機....................................................................................................1
1.2 文獻探討....................................................................................................2
1.3 論文架構...................................................................................................3
第二章 濾波器設計理論..............................................................................................5
2.1 散射參數...................................................................................................5
2.2 二埠網路的奇偶模態電路分析.............................................................. 7
2.3 平行耦合微帶線之分析.......................................................................... 8
2.4 步階阻抗諧振腔之分析........................................................................ 11
2.5 雙路徑分析............................................................................................ 17
第三章 頻寬與頻帶比可調控之雙頻帶通濾波器................................................... 21
3.1 簡介........................................................................................................ 21
3.2 雙頻帶通濾波器分析.............................................................................22
3.2.1 傳輸零點分析..............................................................................23
3.2.2 通帶頻率位置..............................................................................28
3.2.3 頻帶調控......................................................................................32
3.2.3.1 通帶頻率比的調控.........................................................32
3.2.3.2 頻寬的調控.....................................................................34
3.3 設計實例.................................................................................................37
3.3.1 規格..............................................................................................37
3.3.2 模擬與實做........................................\.........................................37
3.3.2 進階應用......................................................................................47
第四章 雙頻帶通濾波器設計....................................................................................49
4.1 簡介.........................................................................................................49
4.2 雙頻帶通濾波器分析.............................................................................49
4.2.1 奇偶模態電路分析法..................................................................51
4.2.2通帶分分析法.............................................................................. 55
4.3 設計實例.................................................................................................65
第五章 結論................................................................................................................69
參考文獻......................................................................................................................71

[1]S. B. Cohn, “Parallel-coupled transmission-line-resonator filters”, IRE Trans. Microw. Theory and Tech., vol. MTT-6, pp. 223–231, Apr. 1958.
[2]M. Makimoto and S. Yamashita, “Bandpass filters using parallel coupled stripline stepped impedance resonators,” IEEE Trans. Microw. Theory Tech. vol. 28, no. 12, pp. 1413–1417, Dec.1980.
[3]K. U-yen, E. J. Wollack, T. A. Doiron, J. Papapolymerou, and J. Laskar, “A planar bandpass filter design with wide stopband using double split-end stepped-impedance resonators,” IEEE Trans. Microw. Theory Tech. vol. 54, no. 3, pp. 1237–1244, Mar. 2006.
[4]S. F. Chang, Y. H. Jeng and J. L. Chen, “Dual-band step-impedance bandpass filter for multimode wireless LANs,” Electron. Lett., vol.40, no. 1, pp.38–39, Jan. 2004.
[5]C. W. Tang, “Design of a microstrip filter using multiple capacitively loaded coupled lines,” IET Microw. Antennas Propag., vol. 1, no. 3, pp. 651–657, Jun. 2007.
[6]C. H. Wu, C. H. Wang, and C. H. Chen, “Stopband-extended balanced bandpass filter using coupled stepped-impedance resonators,” IEEE Microw. Wireless Compon. Lett., vol. 17, no. 7, pp. 507–509, Jul. 2007.
[7]Y. M. Chen, S. F. Chang, C. C. Chang, and T. J. Hung, “Design of stepped-impedance combline bandpass filters with symmetric insertion-loss response and wide stopband range,” IEEE Trans. Microw. Theory Tech. vol. 55, no. 10, pp. 2191–2199, Oct. 2007.
[8]C. L. Hsu and J. T. Kuo, “A two-stage SIR bandpass filter with an ultra-wide upper rejection band,” IEEE Microw. Wireless Compon. Lett., vol. 17, no. 1, pp. 34–36, Jan. 2007.
[9]J. T. Kuo, C. L. Hsu, and E. Shih, “Compact planar quasi-elliptic function filter with inline stepped-impedance resonators,” IEEE Trans. Microw. Theory Tech. vol. 55, no. 8, pp. 1747–1754, Aug. 2007.
[10]C. W. Tang and Y. K. Hsu, “Design of a wide stopband microstrip bandpass filter with asymmetric resonators,” IEEE Microw. Wireless Compon. Lett., vol. 18, no. 2, pp. 91–93, Feb. 2008.
[11]C. W. Tang and Y. K. Hsu, “A microstrip bandpass filter with ultra-wide stopband,” IEEE Trans. Microw. Theory Tech., vol. 56, no. 6, pp. 1468–1472, Jun. 2008.
[12]S. L. March, “Phase velocity compensation in parallel-coupled microstrip,” in IEEE MTT-S Int. Microw. Symp. Dig., 1982, pp.410–412.
[13]J. Bahl, “Capacitively compensated high performance parallel coupled microstrip filters,” in IEEE MTT-S Int. Microw. Symp. Dig., 1989, pp.679–682.
[14]Richard J. Cameron, Ming Yu, and Ying Wang, “Direct-Coupled Microwave Filters With Single and Dual Stopbands,” IEEE Trans. Microw. Theory Tech., vol. 53, no. 11, pp. 3288–3297, Nov. 2005.
[15]H. Joshi and W. J. Chappell, “Dual-band lumped-element bandpass filter,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 12, pp. 4169–4177, Dec. 2006.
[16]H. M. Lee and C. M. Tsai, “Dual-band filter design with flexible passband frequency and bandwidth selections,” IEEE Trans. Microw. Theory Tech., vol. 55, no. 5, pp. 1002–1009, May 2007.
[17]J. Lee and K. Sarabandi, “A synthesis method for dual-passband microwave filters,” IEEE Trans. Microw. Theory Tech., vol. 55, no. 6, pp. 1163–1170, Jun. 2007.
[18]X. Y. Zhang, J. X. Chen, Q. Xue, and S. M. Li, “Dual-band bandpass filters using stub-loaded resonators,” IEEE Microw. Wireless Compon. Lett., vol. 17, no. 8, pp. 583–585, Aug. 2007.
[19]P. Mondal and M. K. Mandal, “Design of dual-band bandpass filters using stub-loaded open-loop resonators,” IEEE Trans. Microw. Theory Tech., vol. 56, no. 1, pp. 150–155, Jan. 2008.
[20]C. M. Tsai, S. Y. Lee, and C. C. Tsai, “Performance of a planar filter using a 0o feed structure,” IEEE Trans. Microw. Theory Tech., vol. 50, no. 10, pp. 2362– 2367, Oct. 2002.
[21]P. K. Singh, S. Basu, and Y. H. Wang, “Miniature dual-band filter using quarter wavelength stepped impedance resonators,” IEEE Microw. Wireless Compon. Lett., vol. 18, no. 2, pp. 88–90, Feb. 2008.
[22]A. S. Liu, T. Y. Huang, and R. B. Wu, “A dual wideband filter design using frequency mapping and stepped-impedance resonators,” IEEE Trans. Microw. Theory Tech., vol. 56, no. 12, pp. 2921–2929, Dec. 2008.
[23]Y. P. Zhang and M. Sun, “Dual-band microstrip bandpass filter using stepped-impedance resonator with new coupling schemes,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 10, pp. 3779–3785, Oct. 2006.
[24]J. Wang, Y. X. Guo, B. Z. Wang, L. C. Ong, and S. Xiao, “High selectivity dual-band stepped-impedance bandpass filter,” Electron. Lett., vol. 42, no. 9, pp. 1–2, Apr. 2006.
[25]H. K. Jhuang, C. H. Lee, and C. I. G. Hsu, “Design of compact microstrip dual band bandpass filters with λ/4 stepped-impedance resonators,” Microw. Opt. Technol. Lett., vol. 49, no.1, pp. 164–168, Jan. 2007.
[26]J. T. Kuo and H. P. Lin, “Dual-band bandpass filter with improved performance in extended upper rejection band,” IEEE Trans. Microw. Theory Tech., vol. 57, no. 4, pp. 824–829, Apr. 2009.
[27]H. Miyake, S. Kitazawa, T. Ishizaki, T. Yamada, and Y. Nagatomi, “A miniaturized monolithic dual band filter using ceramic lamination technique for dual mode portable telephones,” in IEEE MTT-S Int. Microw. Symp. Dig., 1997, pp. 789–792.
[28]M. H. Weng, R. Y. Yang, Y. C. Chang, H. W. Wu, and K. Shu, “Design of a multilayered dual-band bandpass filter with transmission zeros,” Microw. Opt. Technol. Lett., vol. 50, no. 8, pp. 2010–2013, Aug. 2008.
[29]M. H. Weng, H. W. Wu, K. Shu, J. R. Chen, R. Y. Yang, and Y. K. Su, “A novel triple-band bandpass filter using multlayer-based substrates for WiMAX,” in Proc. 37th Eur. Microw. Conf., 2007, pp. 325–328.
[30]M. Sagawa, M. Makimoto, and S. Yamashita, “Geometrical structures and fundamental characteristics of microwave stepped-impedance resonators,” IEEE Trans. Microw. Theory Tech., vol. 45, no. 7, pp. 1078–1085, Jul. 1997.
[31]M. Sagawa, M. Makimoto, and S. Yamashita, “A design method of bandpass filters using dielectric-filled coaxial resonators,” IEEE Trans. Microw. Theory Tech., vol. MTT-33, no. 2, pp. 152–157, Feb. 1985.
[32]J. T. Kuo and H. S. Cheng, “Design of quasi-elliptic function filters with a dual-passband response,” IEEE Microw. Wireless Comp. Lett., vol. 14, no. 10, pp. 472–474, Oct. 2004.
[33]J. T. Kuo, T. H. Yeh, and C. C. Yeh, “Design of microstrip bandpass filters with a dual-passband response,” IEEE Trans. Microw. Theory Tech., vol. 53, no. 4, pp. 1331–1337, Apr. 2005.
[34]C. L. Hsu, J. T. Kuo, and F. C. Hsu, “Design of loop resonator filters with a dual-passband response,” in Proc. Asia-Pacific Microw. Conf., vol. 3, 4-7 Dec. 2005.
[35]C. Y. Chen, C Y. Hsu, and H. R. Chung, “Design of miniature planar dual-band filter using dual-feeding structures and embedded resonators,” IEEE Microw. Wireless Comp. Lett., vol. 16, no. 12, pp. 669–671, Dec. 2006.
[36]C. W. Tang and P. H. Wu, “Design of a planar dual-band bandpass filter,” IEEE Microwave and Wireless Components Letters, vol. 21, no. 7, pp. 362-364, Jul. 2011.
[37]C. Y. Chen and C. Y. Hsu, “A simple and effective method for microstrip dual-band filters design,” IEEE Microw. Wireless Compon. Lett., vol. 16, no. 5, pp. 246–248, May 2006.
[38]M. I. Lai and S. K. Jeng, “Compact microstrip dual-band bandpass filters design using genetic-algorithm techniques,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 1, pp. 160-168, Jan. 2006.
[39] K. X. Ma, J. G. Ma, K. S. Yeo, and M. A. Do, “A compact size coupling controllable filter with separate electric and magnetic coupling paths,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 3, pp. 1113-1119, Mar. 2006.
[40]R. J. Mao, X. H. Tang and F. Xiao, “Novel Compact Quarter Wavelength Resonator Filter using Lumped Coupling Elements,” IEEE Microw. Wireless Compon. Lett., vol. 17, no. 2, pp. 112-114, Feb. 2007.

QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top