跳到主要內容

臺灣博碩士論文加值系統

(18.97.14.81) 您好!臺灣時間:2025/02/19 03:56
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

我願授權國圖
: 
twitterline
研究生:蔡秉均
研究生(外文):Bing-Jiun Tsai
論文名稱:牙科贋復元件間隙之影像量測系統開發
論文名稱(外文):The Development of Image Measurement System for the Detect of Dental Prosthesis Elements’ Gap
指導教授:張信良張信良引用關係
指導教授(外文):Shinn-Liang Chang
學位類別:碩士
校院名稱:國立虎尾科技大學
系所名稱:動力機械工程系機械與機電工程碩士班
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2016
畢業學年度:104
語文別:中文
論文頁數:57
中文關鍵詞:三維列印假牙影像處理量測
外文關鍵詞:3D printingToothImage processingMeasurement.
相關次數:
  • 被引用被引用:0
  • 點閱點閱:153
  • 評分評分:
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:0
目前常用的間隙量測大多是以接觸的方式為之,國內外對於假牙安裝後間隙量測儀器則是尚在開發階段。目前在牙科診間多以針頭在齒面滑動以觀察間隙是否太大,此一方式不夠精確,且易受施力大小所影響。由於牙齒外形為複雜之曲面且口腔空間狹小,現有的影像量測儀無法適當地測量出贋復元件與牙齒的間隙,量測所耗費的時間也相對多。
有鑑於此,本研究將利用影像處理開發應用於牙科贋復元件的量測技術,包括影像濾波、影像形態學、邊緣偵測,針對假牙的外形輪廓進行特徵的擷取與計算,以量測出假牙間隙,因此本研究提供可靠的間隙量測方式,解決以往無法量測牙科贋復元件製造精度之課題,成果亦可應用於其他型式的複雜外型的檢測。


The possible ways to measure the gap of dental prosthesis element are done by contact of probe or image processing. However, the gap measuring instrument to detect the denture installation is still in development. In order to judge the gap of denture is too large or not, dentists use a needle to scrape on the surface of denture. This way is easily affected by the applied force and causes misjudgment. Because the commercial image measurement instrument cannot properly measure the gap of denture in the narrow mouth. Therefore, this study aims to develop a device to detect the gap of dental, such the device is not found currently in industry.
Based on the requirement, this study applies image processing to develop a system for gap measurement of dental prosthesis element. The system functions use image filtering, image morphology, and edge detection to capture and calculate the contour for the gap measurement of dental. The developed measurement system could combine with the oral camera to improve its application. The results in this study are efficient to measure the gap of dental prosthesis elements.


摘要...i
Abstract...ii
誌謝...iv
目錄...v
表目錄...viii
圖目錄...ix
第一章 緒論...1
1.1前言...1
1.2研究動機與目的...1
1.3文獻回顧...2
1.4論文架構...3
第二章 研究方法...5
2.1 數位影像處理...5
2.2 影像灰階轉換...6
2.3 影像濾波遮罩...8
2.3.1 平滑低通濾波器...10
2.3.2 銳化高通濾波器...11
2.4 影像二值化...16
2.4.1 二值影像閥值擷取...17
2.5 消除影像孤立點...17
2.5.1 侵蝕(Erosion)與膨脹(Dilation)...18
2.6 邊緣濾波(邊緣檢測)...19
2.6.1 Laplacian 邊緣運算元...19
2.6.2 Sobel 邊緣運算元...20
2.6.3 比對式邊緣偵測...21
第三章 像素運算原理...23
3.1像素線段長度...23
3.2定義像素尺寸...24
3.3 像素點搜索...24
3.4 最小平方法...25
第四章 影像量測設備....27
4.1 影像量測系統架構...27
4.2 口外量測影像量測系統設備介紹...29
4.3 影像擷取系統原理與光源...32
4.4 系統在口腔內窺鏡之應用...34
第五章 贋復元件量測之實驗流程與結果...35
5.1使用者視窗環境介面...35
5.2像素解析度校正...35
5.3影像量測程序...39
5.4 繪製基準線...40
5.5間隙量測...41
5.6口腔檢測儀試製...43
5.7量測結果分析...44
第六章 結論與未來展望...47
6.1結論...47
6.2未來展望...48
參考文獻...49
Extended Abstract...52
1. Image Measurement System...53
2. Pixel Correction...54
3. Measurement Result...55
4. Conclusion...56
簡歷(CV)...57


[1]D. W. Manthey, K. N. Knapp, and D. Lee, “Calibration of a Laser Range Finding Coordinate Measuring Machine ,” Opt. Eng. , Vol. 33 , No. 10 , pp.3272 -2379 , October 1994 .
[2]C. Bradley and G. W. Vickers, “Free–from surface Reconstruction for machine vision rapid prototyping”, Opt. Eng., Vol. 32, No. 9,pp.2191-2200, September 1993.
[3]A. Huertas, “Detection of Intensity Changes with Sub-pixel Accuracy using Laplacian-Gaussian Masks,” IEEE Trans. On Pattern Analysis and Machine Intelligence, Vol. 8, No. 5, pp. 651-664, September 1986.
[4]A.P. Pentland, “A New Sense for Depth of Field,” IEEE Trans-actions on Pattern Analysis and Machine Intelligence, Vol. 9, No. 4, pp. 523-531, July 1987.
[5]S.K. Nayar and Y. Nakagawa, “Shape from Focus: An Effective Approach for Rough Surfaces,” IEEE International Conference on Robotics and Automation, Vol. 2, No. 10, pp. 218-225, 1990.
[6]M. Subbarao and T. Choi, “Accurate Recovery of Three-Dimensional Shape from Image Focus,” IEEE Transaction On Pattern Analysis and Machine Intelligence, Vol. 17, No. 3, pp. 266-274, March. 1995.
[7]G. Shrivakshan and C. Chandrasekar, “A Comparison of various Edge Detection Techniques used in Image Processing,” International Journal of Computer Science Issues, Vol. 9, No 5, pp.269-276, September 2012.
[8]N. Senthilkumaran and R. Rajesh, “Edge Detection Techniques for Image Segmentation and A Survey of Soft Computing Approaches,” International Journal of Recent Trends in Engineering, Vol. 1, No. 2, pp.250-254, May 2009.
[9]Wenshuo Gao, Lei Yang, Xiaoguang Zhang, and Huizhong Liu, “An Improved Sobel Edge Detection,” 2010 3rd IEEE International Conference on Computer Science and Information Technology, Vol. 5, pp. 67 - 71, 9-11, July 2010.
[10]蔡佑男,“齒模三維輪廓量測”,碩士論文,中原大學機械工程學系,1991年。
[11]蔡明忠,“非接觸式測距與3D 視覺技術”,機械工業雜誌,163-169頁,1995年1月。
[12]張東明,“影像處理於加工定位之應用”, 碩士論文,國立臺灣大學機械工程學系,1996年。
[13]李高明,“機器視覺在物體尺寸精密量測之應用研究”, 碩士論文,中原大學機械工程研究所,1997年。
[14]陳時新,“實戰機器視覺”,電子技術出版社,1997年。
[15]黃德昌,“影像處理與虛擬實境在醫學上的應用”,碩士論文,國立中央大學機械工程學系,2000年。
[16]林岡品,“彩色影像的半自動切割方法”,碩士論文,中山大學機械與機電工程學系,2002年。
[17]蕭裕昌,“應用影像量測技術於微小元件之外型尺寸量測之研究”,碩士論文,淡江大學航空太空工程學系,2003年。
[18]黃建銘,“應用非接觸式影像量測技術於微小元件外形尺寸量測之研究”,碩士論文,淡江大學航空太空工程學系,2003年。
[19]黃建強,“虛擬牙模之重建及對位”,碩士論文,成功大學醫學工程學系,2004年。
[20]許捷皓,“運用校正版與鏡頭光學參數的內視鏡影像校正法”,碩士論文,中原大學電子工程學系,2004年。
[21]李建旻,“影像識別在保全系統上的應用”,碩士論文,南台科技大學電機工程學系,2005年。
[22]吳嘉宏,“邊緣線檢測技術於二維量測誤差之探討”,碩士論文,成功大學航空太空工程學系,2006年。
[23]陳菡均,“快速義齒鑲製系統關鍵幾何之量測與重建”,碩士論文,大同大學機械工程學系,2007年。
[24]王迪藝,“非接觸式單CCD義齒鑲製關鍵邊緣線掃描量測系統”,碩士論文,大同大學機械工程學系,2008年。
[25]陳韡中,“齒輪影像量測系統之開發”,碩士論文,國立國立虎尾科技大學機械與機電工程所,2009年。
[26]劉俊佳,“非圓形齒輪量測系統之開發”,碩士論文,國立國立虎尾科技大學機械與機電工程所,2015年。
[27]精密儀器發展中心,“儀器總覽”,精密儀器發展中心,1998年。



QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top