臺灣博碩士論文加值系統

本論文提出一具部分功率調節之發光二極體(Light-Emitting Diode, LED) 可調光驅動電路。驅動電路中採用多輸出返馳式轉換器，以多相脈衝寬度調變控制，個別調節三原色LED串列電流，混合成期望的白光色溫。論文內容分析驅動電路的操作模式，推導參數設計方程式。設計兩組實驗電路，分別驅動由相同數目的三原色LED串列組成45-W之LED燈，和三串切入電壓相近的三原色LED串列組成35-W之LED燈。實驗結果顯示，在LED燈可調光範圍中，具部分功率調節功能之驅動電路整體轉換效率比傳統返馳式轉換器高約4%至5%。

An efficient light-emitting diode (LED) driver with dimming control is proposed based on a topology with partial power regulation. The currents on red-green-blue (RGB) LED strings are individually regulated by a multi-output flyback converter. A multi-phase pulse-width modulation scheme is used to dim the RGB LEDs with desired lighting performances. The circuit operation of the driver is analyzed, and then the design equations for designing the circuit parameters are derived accordingly. Two laboratory circuits are designed for a 45-W lamp formed by RGB LED strings with a same number of LEDs and a 35-W lamp with an identical cut-in voltage in three LED strings, respectively. The experimental results show that the overall power conversion efficiency of the driver circuit with partial power regulation is 4% to 5% higher than that of the conventional flyback converter over the dimmable range.

論文審定書 i
中文摘要 ii
Abstract iii
Contents iv
List of Figures vi
List of Tables viii
Chapter 1 Introduction 1
1.1 Research Background and Motivation 1
1.2 Content Arrangement 3
Chapter 2 Introduction to White-Light LEDs and Drivers 4
2.1 White-Light LEDs 4
2.2 Fundamentals of Color Science 8
2.3 Electric Characteristics of RGB LEDs 10
2.4 LED Drivers 12
Chapter 3 Analysis of the Driver with Multi-Phase Dimming 14
3.1 Circuit Configuration 14
3.2 Multi-phase PWM Dimming Control 18
3.3 Power Conversion Efficiency 20
3.4 Circuit Operation 22
3.5 Circuit Analysis 25
3.6 Design Procedure 28
3.7 Feedback Control Circuit 29
Chapter 4 Design and Experiment 32
4.1 Case I: LED Strings with Same Number of LEDs 32
4.1.1 Circuit Specifications 32
4.1.2 Experimental Results 36
4.2 Case II: LED Strings with Same Cut-In Voltage 40
4.2.1 Circuit Specifications 40
4.2.1 Experimental Results 43
4.3 Comparison of Circuit Efficiencies 48
4.4 White-Light Generated with the RGB LEDs 50
Chapter 5 Conclusion and Future Work 53
5.1 Conclusion 53
5.2 Future Work 55
References 56

[1] J. Peck, G. Ashburner, and M. Schratz, “Solid state LED lighting technology for hazardous environments: Lowering total cost of ownership while improving safety, quality of light and reliability,” in Proc. IEEE PCIC EUROPE, June 2011, pp. 1–8.
[2] G. Shahzad, H. Yang, A. W. Ahmad, and C. Lee, “Energy-efficient intelligent street lighting system using traffic-adaptive control,” IEEE Sensors J., vol. 16, no. 13, pp. 5397–5405, July 2016.
[3] L. Corradini and G. Spiazzi, “A high-frequency digitally controlled LED driver for automotive applications with fast dimming capabilities,” IEEE Trans. Power Electron., vol. 29, no. 12, pp. 6648–6659, Dec. 2014.
[4] Y. L. Lin, H. J. Chiu, Y. K. Lo, and C. M. Leng, “LED backlight driver circuit with dual-mode dimming control and current-balancing design,” IEEE Trans. Ind. Electron., vol. 61, no. 9, pp. 4632–4639, Sep. 2014.
[5] M. F. Melo, W. D. Vizzotto, P. J. Quintana, A. L. Kirsten, M. A. Dalla Costa, and J. Garcia, “Bidirectional grid-tie flyback converter applied to distributed power generation and street lighting integrated system,” IEEE Trans. Ind. Appl., vol. 51, no. 6, pp. 4709–4717, Nov. 2015.
[6] S. Choi and T. Kim, “Symmetric current-balancing circuit for LED backlight with dimming,” IEEE Trans. Ind. Electron., vol. 59, no. 4, pp. 1698–1707, Apr. 2012.
[7] K. H. Loo, Y. M. Lai, S. C. Tan, and C. K. Tse, “On the color stability of phosphor-converted white LEDs under DC, PWM, and bilevel drive,” IEEE Trans. Power Electron., vol. 27, no. 2, pp. 974–984, Feb. 2012.
[8] F. Rahman, A. F. George, and R. Drinkard, “Short- and long-term reliability studies of broadband phosphor-converted red, green, and white light-emitting diodes,” IEEE Trans. Device Mater. Rel., vol. 16, no. 1, pp. 1–8, Mar. 2016.
[9] S. Choi and T. Kim, “Dynamic prediction of correlated color temperature and color rendering index of phosphor-coated white light-emitting diodes,” IEEE Trans. Ind. Electron., vol. 61, no. 2, pp. 784–797, Feb. 2014.
[10] D. Gacio, J. M. Alonso, J. Garcia, D. Garcia-Llera, and J. Cardesin, “Study on passive self-equalization of parallel-connected LED strings,” IEEE Trans. Ind. Appl., vol. 51, no. 3, pp. 2536–2543, May/June 2015.
[11] X. Qu, S. C. Wong, and C. K. Tse, “Temperature measurement technique for stabilizing the light output of RGB LED lamps,” IEEE Trans. Instrum. Meas., vol. 59, no. 3, pp. 661–670, Mar. 2010.
[12] S. K. Ng, K. H. Loo, Y. M. Lai, and C. K. Tse, “Color control system for RGB LED with application to light sources suffering from prolonged aging,” IEEE Trans. Ind. Electron., vol. 61, no. 4, pp. 1788–1798, Apr. 2014.
[13] Y. F. Cheung and H. W. Choi, “Color-tunable and phosphor-free white-light multilayered light-emitting diodes,” IEEE Trans. Electron Devices, vol. 60, no. 1, pp. 333–338, Jan. 2013.
[14] M. S. Lin and C. L. Chen, “An LED driver with pulse current driving technique,” IEEE Trans. Power Electron., vol. 27, no. 11, pp. 4594–4601, Nov. 2012.
[15] J. Garcia, M. A. Dalla-Costa, J. Cardesin, J. M. Alonso, and M. Rico-Secades, “Dimming of high-brightness LEDs by means of luminous flux thermal estimation,” IEEE Trans. Power Electron., vol. 24, no. 4, pp. 1107–1114, Apr. 2009.
[16] S. Beczkowski and S. Munk-Nielsen, “LED spectral and power characteristics under hybrid PWM/AM strategy,” in Proc. IEEE ECCE, Sep. 2010, pp. 731–735.
[17] D. Gacio, J. M. Alonso, J. Garcia, L. Campa, M. J. Crespo, and M. Rico-Secades, “PWM series dimming for slow-dynamics HPF LED drivers: the high-frequency approach,” IEEE Trans. Ind. Electron., vol. 59, no. 4, pp. 1717–1727, Apr. 2012.
[18] P. L. Lee, C. L. Yeh, J. Y. S. Cheng, C. Y. Yang, and G. Y. Lan, “An SSVEP-based BCI using high duty-cycle visual flicker,” IEEE Trans. Biomed. Eng., vol. 58, no. 12, pp.3350–3359, Dec. 2011.
[19] H. van der Broeck, G. Sauerlander, and M. Wendt, “Power driver topologies and control schemes for LEDs,” in Proc. IEEE APEC, Feb. 2007, pp. 1319–1325.
[20] H. J. Chiu, Y. K. Lo, T. P. Lee, S. C. Mou, and H. M. Huang, “Design of an RGB LED backlight circuit for liquid crystal display panels,” IEEE Trans. Ind. Electron., vol. 56, no. 7, pp. 2793–2795, July 2009.
[21] Y. H. Liu, Z. Z. Yang, and S. C. Wang, “A novel sequential-color RGB-LED backlight driving system with local dimming control and dynamic bus voltage regulation,” IEEE Trans. Consum. Electron., vol. 56, no. 4, pp. 2445–2452, Nov. 2010.
[22] K. Modepalli and L. Parsa, “A scalable n-color LED driver using single inductor multiple current output topology,” IEEE Trans. Power Electron., vol. 31, no. 5, pp. 3773–3783, May 2016.
[23] C. S. Moo, Y. J. Chen, and W. C. Yang, “An efficient driver for dimmable LED lighting,” IEEE Trans. Power Electron., vol. 27, no. 11, pp. 4613–4618, Nov. 2012.
[24] J. M. Alonso, J. Vina, D. G. Vaquero, G. Martinez, and R. Osorio, “Analysis and design of the integrated double buck–boost converter as a high-power-factor driver for power-LED lamps,” IEEE Trans. Ind. Electron., vol. 59, no. 4, pp. 1689–1697, Apr. 2012.
[25] J. Zhang, J. Wang, and X. Wu, “A capacitor-isolated LED driver with inherent current balance capability,” IEEE Trans. Ind. Electron., vol. 59, no. 4, pp. 1708–1716, Apr. 2012.
[26] B. Poorali and E. Adib, “Analysis of the integrated SEPIC-flyback converter as a single-stage single-switch power-factor-correction LED driver,” IEEE Trans. Ind. Electron., vol. 63, no. 6, pp. 3562–3570, June 2016.
[27] C. S. Moo, Y. J. Chen, Y. J. Li, and H. C. Yen, “A dimmable LED driver with partial power regulation,” in Proc. IEEE IECON, Nov. 2015, pp. 672–677.
[28] P. S. Almeida, H. A. C. Braga, M. A. Dalla-Costa, and J. M. Alonso, “Offline soft-switched LED driver based on an integrated bridgeless boost–asymmetrical half-bridge converter,” IEEE Trans. Ind. Electron., vol. 51, no. 1, pp. 761–769, Jan./Feb. 2015.
[29] J. Zhao, K. Yeates, and Y. Han, “Analysis of high efficiency DC/DC converter processing partial input/output power,” in Proc. IEEE COMPEL, June 2013, pp. 1–8.
[30] M. S. Agamy et al., “An efficient partial power processing DC/DC converter for distributed PV architectures,” IEEE Trans. Power Electron., vol. 29, no. 2, pp. 674–686, Feb. 2014.
[31] A. Diab-Marzouk and O. Trescases, “SiC-based bidirectional Ćuk converter with differential power processing and MPPT for a solar powered aircraft,” IEEE Trans. Transpor. Electrif., vol. 1, no. 4, pp. 369–381, Dec. 2015.
[32] T. Q. Khan, P. Bodrogi, Q. T. Vinh, and H. Winkler, LED Lighting: Technology and Perception. Weinheim, Germany: WILEY-VCH, 2014.
[33] Committee on Assessment of Solid-State Lighting et al, Assessment of Advanced Solid-State Lighting. The National Academies Press, 2013. [Online]. Available: http://www.nap.edu/catalog.php?record_id=18279
[34] D. A. Steigerwald et al, “Illumination with solid state lighting technology,” IEEE J. Sel. Top. Quantum Electron., vol. 8, no. 2, pp. 310–320, Mar./Apr. 2002.
[35] E. F. Schubert, Light-Emitting Diodes. Cambridge, U.K.: Cambridge Univ. Press, 2003.
[36] S. Winder, Power Supplies for LED Driving. Oxford, U.K.: Butterworth-Heinemann, 2008.
[37] A. S. Sedra and K. C. Smith, Microelectronic Circuits. London, U.K.: Oxford Univ. Press, 2004.
[38] R. L. Lee and Y. F. Chen, “Equivalent circuit model of light-emitting-diode for system analyses of lighting drivers,” in Proc. IEEE IAS, Oct. 2009, pp. 1–5.
[39] R. L. Lee, S. Y. Liu, C. C. Lee, and Y. C. Chen, “Taylor-series-expression-based equivalent circuit models of LED for analysis of LED driver system,” IEEE Trans. Ind. Appl., vol. 49, no. 4, pp. 1854–1862, July/Aug. 2013.
[40] R. L. Lee, Y. C. Chen, and C. C. Lee, “Optimal design of LED array for single-loop CCM buck–boost LED driver,” IEEE Trans. Ind. Appl., vol. 49, no. 2, pp. 761–768, Mar./Apr. 2013.
[41] T. H. Yu, T. J. Liang, K. H. Chen, J. S. Li, and J. S. Lee, “Design of an AC-DC and DC-DC interleaved PWM controller for switching power supply,” in Proc. IEEE ECCE, Sep. 2013, pp. 4172–4179.
[42] J. E. Park, J. W. Kim, B. H. Lee, and G. W. Moon, “Design on topologies for high efficiency two-stage AC-DC converter,” in Proc. IEEE IPEMC, June 2012, pp. 257–262.
[43] M. Arias, M. F. Diaz, D. G. Lamar, D. Balocco, A. A. Diallo, and J. Sebastián, “High-efficiency asymmetrical half-bridge converter without electrolytic capacitor for low-output-voltage AC–DC LED drivers,” IEEE Trans. Power Electron., vol. 28, no. 5, pp. 2539–2550, May 2013.
[44] Y. C. Shen et al, “Non-electrolytic capacitor LED driver with feedforward control,” in Proc. IEEE ECCE, Sep. 2015, pp. 3223–3230.
[45] Y. Hu, L. Hubber, and M. M. Jovanović, “Single-stage, universal-input AC/DC LED driver with current-controlled variable PFC boost inductor,” IEEE Trans. Power Electron., vol. 27, no. 3, pp. 1579–1588, Mar. 2012.
[46] Y. C. Chuang, Y. L. Ke, H. S. Chuang, and C. C. Hu, “Single-stage power-factor-correction circuit with flyback converter to drive LEDs for lighting applications,” in Proc. IEEE IAS, Oct. 2010, pp. 1–9.
[47] Y. C. Li and C. L. Chen, “A Novel primary-side regulation scheme for single-stage high-power-factor AC–DC LED driving circuit,” IEEE Trans. Ind. Electron., vol. 60, no. 11, pp. 4978–4986, Nov. 2013.
[48] A. F. Witulski, “Introduction to modeling of transformers and coupled inductors,” IEEE Trans. Power Electron., vol. 10, no. 3, pp. 349–357, May 1995.
[49] Texas Instruments, “TMS320F2833x, TMS320F2823x digital signal controllers (DSCs).”
[50] Avago Technologies, “HCPL-3180 2.5 amp output current, high speed, gate drive optocoupler,” 2009.