跳到主要內容

臺灣博碩士論文加值系統

(44.222.134.250) 您好!臺灣時間:2024/10/07 03:08
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:詹舒博
研究生(外文):Chan, Shu-Po
論文名稱:擾流器與管道截面形狀引導之核心流與近壁流對熱交換器熱傳效能之影響
論文名稱(外文):Influence of Core Flow and Boundary Layer Flow Induced by Perturbator and Channel Cross-Sectional Geometry on Heat Transfer Performance in Heat Exchangers
指導教授:劉通敏劉通敏引用關係張始偉張始偉引用關係
指導教授(外文):Liou, Tong-MiinChang, Shyy-Woei
口試委員:黃榮芳楊建裕王訓忠陳志敏吳興茂
口試委員(外文):Huang, Rong-FungYang, Chien-YuhWong, Shwin-ChungChen, Jerry-M.Wu, Xing-Mao
口試日期:2017-11-06
學位類別:博士
校院名稱:國立清華大學
系所名稱:動力機械工程學系
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2017
畢業學年度:106
語文別:英文
論文頁數:328
中文關鍵詞:質點影像測速儀紅外線測溫儀平行四邊形管道入口效應肋條角度百葉窗型擾流器核心流干擾近壁流干擾紊流熱傳
外文關鍵詞:PIVInfrared ThermographyParallelogram ChannelEntrance EffectRib AngleLouverCore Flow DisturbanceBoundary Layer DisturbanceTurbulent FlowHeat Transfer
相關次數:
  • 被引用被引用:0
  • 點閱點閱:407
  • 評分評分:
  • 下載下載:16
  • 收藏至我的研究室書目清單書目收藏:0
本研究分別使用質點影像測速儀(Particle Image velocimetry)、紅外線測溫儀(Infrared Thermometry)及壓力傳感器(pressure transducer)來量測流場結構、壁溫分布及壓力差值,雷諾數(Reynolds number)在壁溫分布及壓差量測實驗中從5,000變化至20,000,而流場結構量測實驗時,雷諾數則訂於10,000。本文將會分成以下三個部分以探討核心流干擾與近壁流干擾對於流體動量及能量傳遞之影響:
本研究的第一部份選擇平滑平行四邊形銳轉雙通道做為基礎案例,此雙通道前將加裝一不對稱突縮入口(ASI)以模擬實際渦輪機葉片冷卻通道之入口條件,藉此探討入口與平行四邊形截面形狀對於流場、熱傳及壓損的綜合效應。為探討流力參數與熱傳表現之間的關係,主要量測的流力參數有管道截面二次流、近壁面速度分布及紊流動能,本研究發現目前所使用之平行四邊形上、下壁面兩側存在不對稱的流場及熱傳分布,此一發現與對稱的方形及矩形管道有著顯著的不同。此外,與先前加裝全展入口(FDI)之平滑平行四邊形雙通道相比,本研究所使用之仿真入口能額外導引出二次流並且提高流體紊動強度,在較低的范寧摩擦係數(f)下提供較高的紐賽數(Nu),進而提升定泵功率下之熱效能係數(TPF),提升之幅度分別在雷諾數5,000及20,000的條件下達到43.5及53.7個百分比。
做為本研究第一部份之延續,本研究的第二部分將三種不同角度(45、−45及90度)的肋條加裝在搭載仿真入口的平行四邊形雙通道中以探討肋條角度與入口之綜合效應,實驗結果主要探討此綜合效應對於平均速度、二次流、紊動強度、紊動動能、雷諾剪切應力、局部與平均紐賽數及摩擦係數之影響。本研究發現此一綜合效應不只影響著離入口最近的第一通道,影響的範圍甚至延伸至整個平行四邊形雙通道,而在三個肋條角度當中,45度肋條能有效增強入口及平行四邊形傾斜側壁之綜合效應,並使得上、下壁面的紐賽數差異再次擴大,相較之下,另外兩個角度之肋條則因無法增強上述之綜合效應(尤以90度肋條最為明顯)而縮小上、下壁面的紐賽數差異。基於增強面平均紐賽數之能力,在平行四邊形上、下壁面最佳之肋條角度分別為45度及90度,此一結果與先前方形及矩形管道中之數據差異甚大。總體來說,三個肋化之平行四邊形雙通道皆能在定泵功率下提供較高的熱傳增益(TPF>1),但是僅有在能增強入口效應之45度肋化管道中,定泵功率下之熱效能係數能一直維持高於搭載仿真入口的平滑平行四邊形雙通道中的值,因此在平行四邊形雙通道中加入肋條增益熱傳前,一定得考慮入口效應來決定放置何種角度之肋條。
本研究的第三部分基於肋條(Rib)及折流板(Baffle)的熱傳機制與優點設計出新式百葉窗型擾流器,百葉窗型擾流器藉由干擾核心流體、壁面衝擊冷卻及延伸散熱面積三種方式來增益管道內熱傳表現,為簡化研究題目並釐清新式擾流器之影響,搭載全展流入口之正方形雙通道被採用做為第三部分的測試管道,實驗探討擾流器間距比(Pi/DH=1, 2, 3, 4, and ∞)及導流板數量(1≤Ns≤4)對於局部與平均紐賽數、摩擦係數及定泵功率下之熱效能係數的影響以找出新式擾流器之最佳設計。實驗結果顯示紐賽數比及摩擦係數比皆隨著間距比的變小及導流板數量的增加而上升,在所有測試的情況當中,擁有最小間距(Pi/DH=1)及最多導流板(Ns=4)的管道提供最高的熱傳增益,其增益幅度為正方形平滑雙通道之兩倍,然而,在此管道當中其壓損係數亦是所有測試管道當中的最大;此外,本研究亦發現正方形雙通道加裝百葉窗型擾流器之後其定泵功率下之熱效能係數不太隨擾流器間距而改變,且當導流板數量大於3時,熱效能係數亦不太隨導流板數量而改變,但當導流板數量小於3時,熱效能係數隨導流板數量減少而增加。綜合以上,在本研究之實驗條件範圍內,加裝越多百葉窗型擾流器且增加導流板數量(干擾核心流)可以大幅增強管道內熱傳表現,另一方面,干擾壁面流體則是較為經濟實惠的熱傳增益方式(定泵功率下之熱效能係數較高)。
This work attempts to enlighten the influence of core flow disturbance and boundary layer disturbance on momentum and energy transport. Local temperature distributions over entire heated surfaces with the associated pressure drops are examined using Infrared Thermometry (IT) and pressure transducers with Reynolds number (Re) ranging from 5,000 to 20,000. The detailed turbulent flow features are measured with Particle Image velocimetry (PIV) to provide the flow physics attributed to the heat transfer performances at a fixed Re of 10,000.
The first part of the present study explores the detailed flow fields, heat transfer distributions, and pressure drop penalties in a stationary two-pass smooth parallelogram channel with 180-deg sharp bend as the baseline case. The particular asymmetrically and suddenly contracted inlet condition (hereinafter referred to as “ASI”) emulates the abrupt flow entrance of the real gas turbine blade cooling conditions. The secondary-flow patterns as well as the near-wall streamwise mean velocity components and turbulent kinetic energy are analyzed to correlate the relationship between flow characteristics and heat transfer distributions. The most distinct finding of this study is the asymmetric thermal and fluid flow features on the top and bottom wall side, in contrast to the symmetric ones in the corresponding square and rectangular channels. Compared with the previous fully developed inlet condition (hereinafter referred to as “FDI”) case, it is found that the thermal performance factors (TPF) of the ASI case are respectively 43.5% and 53.7% higher than those of the FDI case at Re=5,000 and 20,000 because of the entrance-induced secondary flow and disturbance. The correlations of Nu and fanning friction factor (f) are obtained to compare with those generated from the corresponding square channels.
The second part of the present study explores the detailed flow patterns and turbulence parameters, including streamwise and spanwise mean flow field, secondary-flow mean velocity map, turbulent intensity, Reynolds stress and turbulent kinetic energy as well as the heat transfer performances for the two-pass ribbed parallelogram channels with three different rib orientations (45-deg, -45-deg, and 90-deg). It is found that the combined effect of inlet condition and rib orientation extends to the entire parallelogram channel rather than the first passage only. Among the rib orientations investigated, the 45-deg ribs enhance the effects of parallelogram slant sidewalls and entrance to extend the Nu differences between the top and bottom walls. In contrast, the other two rib configurations, 90-deg ribs especially, weaken these effects and narrow the corresponding differences. Based on the ability to elevate the surface-averaged Nu/Nu∞ ratios, the respective orders of (45-deg, −45-deg, 90-deg) and (90-deg, 45-deg, −45-deg) for the present top and bottom walls are significantly different from those in square and rectangular channels. The variations of channel-averaged Nu/Nu∞ and f/f∞ with the associated TPF values against Re are compared with the previous results obtained from literature. In general, the three tested angled ribs all provide the TPF values above than unity. Only the TPF values in 45-deg case are always higher than those in corresponding smooth parallelogram channel (ASI case). Divided by the TPF values in ASI case, the normalized TPF values are respectively 1.09-1.04, 1.07-0.87, and 0.83-0.99 for 45, 90, −45-deg ribbed cases. It is thus important to take the entrance effect into account when applying the angled ribs in a two-pass parallelogram channel.
The third part of the present study aims to propose innovative louver-type turbulators to enhance the heat transfer rate via three flow mechanics, namely core flow disturbance, jet impingement, and extended heat transfer surface. These louvers are installed in the twin-pass square channel with a fully developed inlet condition. The parameters are examined to disclose optimal design in terms of the pitch ratio (Pi/DH=1, 2, 3, 4, and ∞) and the number of slat per half louver (1≤Ns≤4). The pressure drop measurements are also performed to estimate the Fanning friction factors (f) and the thermal performance factors (TPF). The results show that both (Nu) ̅/Nu∞ and f ̅/f∞ ratios rise with descending Pi/DH and ascending Ns under the present test conditions. Among all the tested cases, the case with Pi/DH=1 and Ns=4 provides the highest Nu/Nu∞, almost twice the value of smooth reference. Nevertheless, it suffers from high f/f∞ penalty. The TPF level is a relatively weak function of Pi/DH. There exists a critical slat number of Ns=3 above which the TPF value is a weak function of Ns. Below the critical Ns, the TPF value increases with decreasing Ns. From the viewpoint of heat transfer enhancement, one could apply the louvered channel as a heat exchanger with small Pi/DH and large Ns. The boundary layer disturbance, on the other hand, is more cost-effective than core flow disturbance as a mechanism to augment heat transfer from the viewpoint of thermal performance.
List of Tables 1
List of Figures 2
Nomenclatures 12
Chapter 1 Introduction 15
1-1 Opening Remarks 15
1-2 Literature Survey 16
1-2-1 Impacts of Channel Configuration 17
1-2-1-1 Cross-Sectional Geometry of Channel 17
1-2-1-2 Channel Aspect Ratio 19
1-2-1-3 Turn Geometry 23
1-2-2 Entrance Configuration 24
1-2-3 Turbulator Configuration 25
1-2-3-1 Turbulator Type 25
1-2-3-2 Turbulator Pitch and Blockage Ratio 30
1-2-3-3 Turbulator Orientation 33
1-3 Objectives 38
Chapter 2 Experimental Setup 64
2-1 Model Configuration 64
2-2 Experimental Apparatus 67
2-2-1 Coolant Flow System 67
2-2-2 Flow Field Measurement System 67
2-2-2-1 Principle of Particle Image Velocimetry 67
2-2-2-2 Illumination System 69
2-2-2-3 Image Collecting System 69
2-2-2-4 Seeding Generator and Tracking Particle 69
2-2-3 Heat Transfer Measurement System 74
2-2-3-1 Background of Thermal Radiation 74
2-2-3-2 Principle of Infrared Thermography 77
2-2-3-3 Heating and Data Acquisition System 78
2-2-4 Pressure Loss Measurement System 78
2-3 Test Condition and Data Processing 79
2-4 Uncertainty Analysis 81
Chapter 3 Flow Field and Heat Transfer Performance in a Smooth Two-Pass Parallelogram Channel 101
3-1 Validation of Flow Measurement Technique 101
3-2 Flow Characteristics in the Upstream Leg 101
3-3 Flow Patterns through Bend Region 103
3-4 Flow Features in the Downstream Leg 105
3-5 Local Nusselt Number and Corresponding Near-Wall Flow Field 106
3-6 Correlation between Flow Feature and Heat Transfer 111
3-7 Effect of Reynolds Number on Heat Transfer 113
3-8 Friction Factor and Heat Transfer Performance 115
Chapter 4 Flow Field and Heat Transfer Performance in Ribbed Two-Pass Parallelogram Channels 150
4-1 Flow Characteristics in Upstream Leg 150
4-2 Flow Patterns through Bend Region 157
4-3 Flow Features in Downstream Leg 162
4-4 Normalized Nusselt Number Distribution 169
4-5 Evaluation of Thermal Performance against Re 174
Chapter 5 Flow Field and Heat Transfer Performance in Louvered Two-Pass Square Channels 272
5-1 Effect of Single Louver on Flow Field 272
5-2 Effect of Pitch between Consecutive Louvers 273
5-3 Effect of Number of Slats 276
5-4 Thermal Performance of Proposed Louvers 279
Chapter 6 Conclusions and Future Recommendations 290
6-1 Conclusions 290
6-1-1 Smooth Parallelogram Channel 290
6-1-2 Ribbed Parallelogram Channel 291
6-1-3 Louvered Square Channel 293
6-2 Contributions 294
6-3 Future Recommendations 294
Appendix I Instruments 296
Reference 309
Resume 325
[1] M. Tye-Gingras, L. Gosselin, Investigation on heat transfer modeling assumptions for radiant panels with serpentine layout, Energy and Buildings 43(7) (2011) 1598-1608.
[2] J.J. Hu, X.S. Sun, J.L. Xu, Z.X. Li, Numerical analysis of mechanical ventilation solar air collector with internal baffles, Energy and Buildings 62 (2013) 230-238.
[3] A. Koca, Z. Gemici, Y. Topacoglu, G. Cetin, R.C. Acet, B.B. Kanbur, Experimental investigation of heat transfer coefficients between hydronic radiant heated wall and room, Energy and Buildings 82 (2014) 211-221.
[4] R.S. Bunker, A review of turbine blade tip heat transfer, Annals of the New York Academy of Sciences 934(1) (2001) 64-79.
[5] P. Ligrani, Heat transfer augmentation technologies for internal cooling of turbine components of gas turbine engines, International Journal of Rotating Machinery 2013 (2013).
[6] L.M. Wright, J.C. Han, Heat transfer enhancement for turbine blade internal cooling, Journal of Enhanced Heat Transfer 21(2-3) (2014).
[7] D. Eryener, Thermoeconomic optimization of baffle spacing for shell and tube heat exchangers, Energy Conversion and Management 47(11) (2006) 1478-1489.
[8] E. Ozden, I. Tari, Shell side CFD analysis of a small shell-and-tube heat exchanger, Energy Conversion and Management 51(5) (2010) 1004-1014.
[9] C. Dong, Y.P. Chen, J.F. Wu, Influence of baffle configurations on flow and heat transfer characteristics of trisection helical baffle heat exchangers, Energy Conversion and Management 88 (2014) 251-258.
[10] S. Maharudrayya, S. Jayanti, A.P. Deshpande, Pressure losses in laminar flow through serpentine channels in fuel cell stacks, Journal of Power Sources 138(1) (2004) 1-13.
[11] J.W. Park, X.G. Li, An experimental and numerical investigation on the cross flow through gas diffusion layer in a PEM fuel cell with a serpentine flow channel, Journal of Power Sources 163(2) (2007) 853-863.
[12] S.H. Yu, S.H. Sohn, J.H. Nam, C.J. Kim, Numerical study to examine the performance of multi-pass serpentine flow-fields for cooling plates in polymer electrolyte membrane fuel cells, Journal of Power Sources 194(2) (2009) 697-703.
[13] A. Syuhada, M. Hirota, H. Fujita, S. Araki, M. Yanagida, T. Tanaka, Heat (mass) transfer in serpentine flow passage with rectangular cross-section, Energy Conversion and Management 42(15) (2001) 1867-1885.
[14] J. Schabacker, A. Boelcs, B.V. Johnson, PIV Investigation of the Flow Characteristics in an Internal Coolant Passage with Two Ducts Connected by a Sharp 180 Deg Bend, Proceedings of the ASME Turbo Expo 1998 Conference, 1998.
[15] T.M. Liou, C.C. Chen, Y.Y. Tzeng, T.W. Tsai, Non-Intrusive Measurements of Near-Wall Fluid Flow and Surface Heat Transfer in a Serpentine Passage, International Journal of Heat and Mass Transfer 43(17) (2000) 3233-3244.
[16] W.L. Fu, L.M. Wright, J.C. Han, Rotational Buoyancy Effects on Heat Transfer in Five Different Aspect-Ratio Rectangular Channels with Smooth Walls and 45 Degree Ribbed Walls, Journal of Heat Transfer 128(11) (2006) 1130-1141.
[17] K. Saha, S. Acharya, Effect of Bend Geometry on Heat Transfer and Pressure Drop in a Two-Pass Coolant Square Channel for a Turbine, Journal of Turbomachinery 135(2) (2013).
[18] S. Mochizuki, A. Murata, M. Fukunaga, Effects of Rib Arrangements On Pressure Drop and Heat Transfer in a Rib-Roughened Channel with a Sharp 180 Deg Turn, Journal of Turbomachinery 119(3) (1997) 610-616.
[19] A. Murata, S. Mochizuki, Effect of Rib Orientation and Channel Rotation on Turbulent Heat Transfer in a Two-Pass Square Channel with Sharp 180° Turns Investigated by Using Large Eddy Simulation, International Journal of Heat and Mass Transfer 47(12) (2004) 2599-2618.
[20] A. Nakayama, W.L. Chow, D. Sharma, Calculation of Fully-Developed Turbulent Flows in Ducts of Arbitrary Cross-Section, Journal of Fluid Mechanics 128(Mar) (1983) 199-217.
[21] S. Dutta, J.C. Han, C.P. Lee, Local Heat Transfer in a Rotating Two-Pass Ribbed Triangular Duct with Two Model Orientations, International Journal of Heat and Mass Transfer 39(4) (1996) 707-715.
[22] H. Iacovides, B.E. Launder, H.Y. Li, The Computation of Flow Development Through Stationary and Rotating U-Ducts of Strong Curvature, International journal of heat and fluid flow 17(1) (1996) 22-33.
[23] H. Iacovides, D.C. Jackson, H. Ji, G. Kelemenis, B.E. Launder, K. Nikas, LDA Study of the Flow Development Through an Orthogonally Rotating U-Bend of Strong Curvature and Rib-Roughened Walls, Journal of Turbomachinery 120(2) (1998) 386-391.
[24] T.M. Liou, C.C. Chen, Heat Transfer in a Rotating Two-Pass Smooth Passage with a 180 Degrees Rectangular Turn, International Journal of Heat and Mass Transfer 42(2) (1999) 231-247.
[25] T.M. Liou, C.C. Chen, LDV Study of Developing Flows Through a Smooth Duct with A 180 Deg Straight-Corner Turn, Journal of Turbomachinery 121(1) (1999) 167-174.
[26] J.P. Bons, J.L. Kerrebrock, Complementary Velocity and Heat Transfer Measurements in a Rotating Cooling Passage with Smooth Walls, Journal of Turbomachinery 121(4) (1999) 651-662.
[27] H. Iacovides, M. Raisee, Computation of Flow and Heat Transfer in Two-Dimensional Rib-Roughened Passages, Using Low-Reynolds-Number Turbulence Models, International Journal of Numerical Methods for Heat & Fluid Flow 11(2-3) (2001) 138-155.
[28] T.M. Liou, C.C. Chen, M.Y. Chen, Rotating Effect on Fluid Flow in Two Smooth Ducts Connected by a 180-Degree Bend, Journal of fluids engineering 125(1) (2003) 138-148.
[29] M. Elfert, M.P. Jarius, B. Weigand, Detailed Flow Investigation Using PIV in a Typical Turbine Cooling Geometry with Ribbed Walls, ASME Turbo Expo 2004: Power for Land, Sea, and Air, American Society of Mechanical Engineers, 2004, pp. 533-545.
[30] S.W. Chang, T.M. Liou, S.F. Chiou, S.F. Chang, Heat Transfer in High-Speed Rotating Trapezoidal Duct with Rib-Roughened Surfaces and Air Bleeds from the Wall on the Apical Side, Journal of Heat Transfer 130(6) (2008).
[31] S.W. Chang, T.M. Liou, Y. Po, Coriolis and Rotating Buoyancy Effect on Detailed Heat Transfer Distributions in a Two-Pass Square Channel Roughened by 45 Degrees Ribs at High Rotation Numbers, International Journal of Heat and Mass Transfer 53(7-8) (2010) 1349-1363.
[32] S.W. Chang, T.M. Liou, T.H. Lee, Thermal Performance of Developing Flow in a Radially Rotating Parallelogram Channel with 45 Degrees Ribs, International Journal of Thermal Sciences 52 (2012) 186-204.
[33] T.M. Liou, S.W. Chang, C.C. Yang, Y.A. Lan, Thermal Performance of a Radially Rotating Twin-Pass Smooth-Walled Parallelogram Channel, ASME Turbo Expo 2014: Turbine Technical Conference and Exposition, American Society of Mechanical Engineers, 2014, pp. V05AT12A004-V05AT12A004.
[34] T.M. Liou, S.W. Chang, S.P. Chan, Y.S. Liou, K.C. Chu, Flow Visualization and PIV Measurements in a Two-Pass Smooth-Wall Parallelogram Channel, The 9th Pacific Symposium On flow Visualization and Image Processing, , 2013, pp. 210-224.
[35] T.M. Liou, S.W. Chang, S.P. Chan, Y.S. Liu, Particle Image Velocimetry Measurements in a Two-Pass 90 Degree Ribbed-Wall Parallelogram Channel, Journal of Turbomachinery 137(4) (2015) 041012.
[36] S. Acharya, S. Dutta, T.A. Myrum, R.S. Baker, Periodically Developed Flow and Heat-Transfer in a Ribbed Duct, International Journal of Heat and Mass Transfer 36(8) (1993) 2069-2082.
[37] S. Acharya, T. Myrum, X. Qiu, S. Sinha, Developing and Periodically Developed Flow, Temperature and Heat Transfer in a Ribbed Duct, International Journal of Heat and Mass Transfer 40(2) (1997) 461-479.
[38] A. Murata, S. Mochizuki, Effect of Cross-Sectional Aspect Ratio on Turbulent Heat Transfer in an Orthogonally Rotating Rectangular Smooth Duct, International Journal of Heat and Mass Transfer 42(20) (1999) 3803-3814.
[39] A. Murata, S. Mochizuki, Large Eddy Simulation with a Dynamic Subgrid-Scale Model of Turbulent Heat Transfer in an Orthogonally Rotating Rectangular Duct with Transverse Rib Turbulators, International Journal of Heat and Mass Transfer 43(7) (2000) 1243-1259.
[40] G.G. Su, H.C. Chen, J.C. Han, J.D. Heidmann, Computation of Flow and Heat Transfer in Rotating Two-Pass Rectangular Channels (AR=1: 1, 1: 2, and 1: 4) with Smooth Walls by a Reynolds Stress Turbulence Model, International Journal of Heat and Mass Transfer 47(26) (2004) 5665-5683.
[41] A.K. Saha, S. Acharya, Unsteady RANS Simulation of Turbulent Flow and Heat Transfer in Ribbed Coolant Passages of Different Aspect Ratios, International Journal of Heat and Mass Transfer 48(23-24) (2005) 4704-4725.
[42] S.W. Chang, T.M. Liou, W.C. Juan, Influence of Channel Height on Heat Transfer Augmentation in Rectangular Channels with Two Opposite Rib-Roughened Walls, International Journal of Heat and Mass Transfer 48(13) (2005) 2806-2813.
[43] K.M. Kim, Y.Y. Kim, D.H. Lee, D.H. Rhee, H.H. Cho, Influence of Duct Aspect Ratio on Heat/Mass Transfer in Coolant Passages with Rotation, International journal of heat and fluid flow 28(3) (2007) 357-373.
[44] S.W. Chang, T.M. Liou, J.H. Hung, W.H. Yeh, Heat Transfer in a Radially Rotating Square-Sectioned Duct with Two Opposite Walls Roughened by 45 Deg Staggered Ribs at High Rotation Numbers, Journal of Heat Transfer 129(2) (2007) 188-199.
[45] T.M. Liou, S.W. Chang, J.H. Hung, S.F. Chiou, High Rotation Number Heat Transfer of a 45 Degrees Rib-Roughened Rectangular Duct with Two Channel Orientations, International Journal of Heat and Mass Transfer 50(19-20) (2007) 4063-4078.
[46] A.K. Saha, S. Acharya, Turbulent Heat Transfer in Ribbed Coolant Passages of Different Aspect Ratios: Parametric Effects, Journal of Heat Transfer 129(4) (2007) 449-463.
[47] F. Zhou, S. Acharya, Heat Transfer at High Rotation Numbers in a Two-Pass 4: 1 Aspect Ratio Rectangular Channel With 45deg Skewed Ribs, Journal of Turbomachinery 130(2) (2008) 021019.
[48] T.M. Liou, S.W. Chang, J.S. Chen, T.L. Yang, Y.A. Lan, Influence of Channel Aspect Ratio on Heat Transfer in Rotating Rectangular Ducts with Skewed Ribs at High Rotation Numbers, International Journal of Heat and Mass Transfer 52(23-24) (2009) 5309-5322.
[49] M.A. Smith, R.M. Mathison, M.G. Dunn, Heat Transfer for High Aspect Ratio Rectangular Channels in a Stationary Serpentine Passage With Turbulated and Smooth Surfaces, Journal of Turbomachinery 136(5) (2014).
[50] T.M. Liou, S.W. Chang, C.C. Yang, Heat Transfer and Pressure Drop Measurements of Rotating Twin-Pass Parallelogram Ribbed Channel, International Journal of Thermal Sciences 79 (2014) 206-219.
[51] I. Mayo, T. Arts, A. El-Habib, B. Parres, Two-Dimensional Heat Transfer Distribution of a Rotating Ribbed Channel at Different Reynolds Numbers, Journal of Turbomachinery 137(3) (2015) 031002.
[52] T.M. Liou, C.C. Chen, M.Y. Chen, TLCT and LDV Measurements of Heat Transfer and Fluid Flow in a Rotating Sharp Turning Duct, International Journal of Heat and Mass Transfer 44(9) (2001) 1777-1787.
[53] T.S. Wang, M.K. Chyu, Heat Convection in a 180-Deg Turning Duct with Different Turn Configurations, Journal of Thermophysics and Heat Transfer 8(3) (1994) 595-601.
[54] E.A. Sewall, D.K. Tafti, Large Eddy Simulation of Flow and Heat Transfer in the 180‐Deg Bend Region of a Stationary Gas Turbine Blade Ribbed Internal Cooling Duct, Journal of Turbomachinery 128(4) (2006) 763-771.
[55] H. Iacovides, D. Kounadis, Z. Xu, Experimental Study of Thermal Development in a Rotating Square-Ended U-Bend, Experimental Thermal and Fluid Science 33(3) (2009) 482-494.
[56] K. Saha, S. Acharya, Bend Geometries in Internal Cooling Channels for Improved Thermal Performance, Journal of Turbomachinery 135(3) (2013).
[57] J.C. Han, J.S. Park, Developing Heat-Transfer in Rectangular Channels with Rib Turbulators, International Journal of Heat and Mass Transfer 31(1) (1988) 183-195.
[58] L.M. Wright, W.L. Fu, J.C. Han, Influence of Entrance Geometry on Heat Transfer in Rotating Rectangular Cooling Channels (AR=4:1) with Angled Ribs, Journal of Heat Transfer 127(4) (2005) 378-387.
[59] Y.H. Liu, M. Huh, J.C. Han, S. Chopra, Heat Transfer in a Two-Pass Rectangular Channel (AR=1:4) under High Rotation Numbers, Journal of Heat Transfer 130(8) (2008) 081701.
[60] W.M. Kays, M.E. Crawford, B. Weigand, Convective Heat and Mass Transfer, Tata McGraw-Hill Education2005.
[61] W.L. Fu, L.M. Wright, J.C. Han, Buoyancy Effects on Heat Transfer in Five Different Aspect-Ratio Rectangular Channels with Smooth Walls and 45-Degree Ribbed Walls, ASME Turbo Expo 2005: Power for Land, Sea, and Air, American Society of Mechanical Engineers, 2005, pp. 453-463.
[62] M. Huh, J. Lei, Y.H. Liu, J.C. Han, High Rotation Number Effects on Heat Transfer in a Rectangular (AR=2:1) Two-Pass Channel, Journal of Turbomachinery 133(2) (2011) 021001.
[63] K. Saha, S. Acharya, Effect of Entrance Geometry and Rotation on Heat Transfer in a Narrow (AR=1:4) Rectangular Internal Cooling Channel, ASME Turbo Expo 2014: Turbine Technical Conference and Exposition, American Society of Mechanical Engineers, 2014, pp. V05AT12A040-V05AT12A040.
[64] T.M. Liou, S.H. Chen, Turbulent Heat and Fluid Flow in a Passage Disturbed by Detached Perforated Ribs of Different Heights, International Journal of Heat and Mass Transfer 41(12) (1998) 1795-1806.
[65] T.M. Liou, C.C. Chen, T.W. Tsai, Heat Transfer and Fluid Flow in a Square Duct with 12 Different Shaped Vortex Generators, Journal of Heat Transfer 122(2) (2000) 327-335.
[66] H. Iacovides, D.C. Jackson, G. Kelemenis, B.E. Launder, Y.M. Yuan, Flow and Heat Transfer in a Rotating U-Bend with 45 Degrees Ribs, International journal of heat and fluid flow 22(3) (2001) 308-314.
[67] H. Iacovides, G. Kelemenis, M. Raisee, Flow and Heat Transfer in Straight Cooling Passages with Inclined Ribs On Opposite Walls: An Experimental and Computational Study, Experimental Thermal and Fluid Science 27(3) (2003) 283-294.
[68] G.S. Azad, M.J. Uddin, J.C. Han, H.K. Moon, B. Glezer, Heat Transfer in a Two-Pass Rectangular Rotating Channel with 45-Deg Angled Rib Turbulators, Journal of Turbomachinery 124(2) (2002) 251-259.
[69] T.M. Liou, M.Y. Chen, M.H. Tsai, Fluid Flow and Heat Transfer in a Rotating Two-Pass Square Duct with In-Line 90-Deg Ribs, Journal of Turbomachinery 124(2) (2002) 260-268.
[70] C.C. Chen, T.M. Liou, Rotating Effect On Fluid Flow in a Smooth Duct with a 180-Deg Sharp Turn, ASME Turbo Expo 2000: Power for Land, Sea, and Air, American Society of Mechanical Engineers, 2000, pp. V003T01A036-V003T01A036.
[71] T.M. Liou, S.H. Chen, K.C. Shih, Numerical Simulation of Turbulent Flow Field and Heat Transfer in a Two-Dimensional Channel with Periodic Slit Ribs, International Journal of Heat and Mass Transfer 45(22) (2002) 4493-4505.
[72] D. Chanteloup, Y. Juaneda, A. Bolcs, Combined 3D Flow and Heat Transfer Measurements in a 2-Pass Internal Coolant Passage of Gas Turbine Airfoils, ASME Turbo Expo 2002: Power for Land, Sea, and Air, American Society of Mechanical Engineers, 2002, pp. 509-520.
[73] S.Y. Son, K.D. Kihm, J.C. Han, PIV Flow Measurements for Heat Transfer Characterization in Two-Pass Square Channels with Smooth and 90 Degrees Ribbed Walls, International Journal of Heat and Mass Transfer 45(24) (2002) 4809-4822.
[74] S.V. Ekkad, J.C. Han, Detailed Heat Transfer Distributions in Two-Pass Square Channels with Rib Turbulators, International Journal of Heat and Mass Transfer 40(11) (1997) 2525-2537.
[75] T.M. Liou, M.Y. Chen, Y.M. Wang, Heat Transfer, Fluid Flow, and Pressure Measurements inside a Rotating Two-Pass Duct with Detached 90-Deg Ribs, Journal of Turbomachinery 125(3) (2003) 565-574.
[76] P. Agarwal, S. Acharya, D. Nikitopoulos, Heat Transfer in 1: 4 Rectangular Passages with Rotation, Journal of Turbomachinery 125(4) (2003) 726-733.
[77] S.W. Chang, W.D. Morris, Heat Transfer in a Radially Rotating Square Duct Fitted with In-Line Transverse Ribs, International Journal of Thermal Sciences 42(3) (2003) 267-282.
[78] L. Wang, B. Sundén, Experimental Investigation of Local Heat Transfer in a Square Duct with Continuous and Truncated Ribs, Experimental heat transfer 18(3) (2005) 179-197.
[79] T.M. Liou, S.H. Chen, Y.C. Li, Numerical Simulation of Turbulent Fluid Flow and Heat Transfer in a Ribbed Rotating Two-Pass Square Duct, International Journal of Rotating Machinery 2005(2) (2005) 152-160.
[80] L. Casarsa, T. Arts, Experimental Investigation of the Aerothermal Performance of a High Blockage Rib-Roughened Cooling Channel, Journal of Turbomachinery 127(3) (2005) 580-588.
[81] M. Cakan, Aero-Thermal Investigation of Fixed Rib-Roughened Internal Cooling Passages, Von Karman Institute for Fluid Dynamics2000.
[82] A.K. Viswanathan, D.K. Tafti, Detached Eddy Simulation of Turbulent Flow and Heat Transfer in a Ribbed Duct, Journal of fluids engineering 127(5) (2005) 888-896.
[83] A.K. Viswanathan, D.K. Tafti, Detached Eddy Simulation of Flow and Heat Transfer in Fully Developed Rotating Internal Cooling Channel with Normal Ribs, International journal of heat and fluid flow 27(3) (2006) 351-370.
[84] A.K. Viswanathan, D.K. Tafti, Detached Eddy Simulation of Turbulent Flow and Heat Transfer in a Two-Pass Internal Cooling Duct, International journal of heat and fluid flow 27(1) (2006) 1-20.
[85] M. Tyagi, S. Acharya, Large Eddy Simulations of Flow and Heat Transfer in Rotating Ribbed Duct Flows, Journal of Heat Transfer 127(5) (2005) 486-498.
[86] E.A. Sewall, D.K. Tafti, A.B. Graham, K.A. Thole, Experimental Validation of Large Eddy Simulations of Flow and Heat Transfer in a Stationary Ribbed Duct, International journal of heat and fluid flow 27(2) (2006) 243-258.
[87] L. Wang, J. Hejcik, B. Sunden, PIV Measurement of Separated Flow in a Square Channel with Streamwise Periodic Ribs on One Wall, Journal of fluids engineering 129(7) (2007) 834-841.
[88] L. Wang, M. Salewski, B. Sunden, Turbulent Flow in a Ribbed Channel: Flow Structures in the Vicinity of a Rib, Experimental Thermal and Fluid Science 34(2) (2010) 165-176.
[89] T.M. Liou, Y.S. Hwang, M.Y. Chen, Heat Transfer Improvement by Arranging Detached Ribs on Suction Surfaces of Rotating Internal Coolant Passages, International Journal of Heat and Mass Transfer 50(11) (2007) 2414-2424.
[90] E.A. Sewall, D.K. Tafti, Large Eddy Simulation of Flow and Heat Transfer in the Developing Flow Region of a Rotating Gas Turbine Blade Internal Cooling Duct with Coriolis and Buoyancy Forces, Journal of Turbomachinery 130(1) (2008) 011005.
[91] F. Coletti, T. Arts, Aerodynamic Investigation of a Rotating Rib-Roughened Channel by Time-Resolved Particle Image Velocimetry, Proceedings of the Institution of Mechanical Engineers Part a-Journal of Power and Energy 225(A7) (2011) 975-984.
[92] F. Coletti, I. Cresci, T. Arts, Spatio-Temporal Analysis of the Turbulent Flow in a Ribbed Channel, International journal of heat and fluid flow 44 (2013) 181-196.
[93] O. Labbe, Large-Eddy-Simulation of Flow and Heat Transfer in a Ribbed Duct, Computers & Fluids 76 (2013) 23-32.
[94] C. Berner, F. Durst, D.M. McEligot, Flow Around Baffles, Journal of Heat Transfer 106 (1984) 743.
[95] P. Dutta, S. Dutta, Effect of baffle size, perforation, and orientation on internal heat transfer enhancement, International Journal of Heat and Mass Transfer 41(19) (1998) 3005-3013.
[96] P. Dutta, A. Hossain, Internal cooling augmentation in rectangular channel using two inclined baffles, International journal of heat and fluid flow 26(2) (2005) 223-232.
[97] T.M. Liou, Y. Chang, D.W. Hwang, Experimental and Computational Study of Turbulent Flows in a Channel with Two Pairs of Turbulence Promoters in Tandem, Journal of fluids engineering 112(3) (1990) 302-310.
[98] T.M. Liou, Y.Y. Wu, Y. Chang, LDV Measurements of Periodic Fully-Developed Main and Secondary Flows in a Channel with Rib-Disturbed Walls, Journal of fluids engineering 115(1) (1993) 109-114.
[99] T.A. Myrum, X. Qiu, S. Acharya, Heat-Transfer Enhancement in a Ribbed Duct Using Vortex Generators, International Journal of Heat and Mass Transfer 36(14) (1993) 3497-3508.
[100] W.D. Morris, K.F. RahmatAbadi, Convective Heat Transfer in Rotating Ribbed Tubes, International Journal of Heat and Mass Transfer 39(11) (1996) 2253-2266.
[101] W. Morris, R. Salemi, An Attempt to Experimentally Uncouple the Effect of Coriolis and Buoyancy Forces On Heat Transfer in Smooth Circular Tubes Which Rotate in The Orthogonal Mode, ASME 1991 International Gas Turbine and Aeroengine Congress and Exposition, American Society of Mechanical Engineers, 1991, pp. V004T09A006-V004T09A006.
[102] M.E. Taslim, C.M. Wadsworth, An Experimental Investigation of the Rib Surface-Averaged Heat Transfer Coefficient in a Rib-Roughened Square Passage, Journal of Turbomachinery 119(2) (1997) 381-389.
[103] M.E. Taslim, G.J. Korotky, Low-Aspect-Ratio Rib Heat Transfer Coefficient Measurements in a Square Channel, Journal of Turbomachinery 120(4) (1998) 831-838.
[104] G.J. Korotky, M.E. Taslim, Rib Heat Transfer Coefficient Measurements in a Rib-Roughened Square Passage, Journal of Turbomachinery 120(2) (1998) 376-385.
[105] M.E. Taslim, A. Lengkong, 45 Deg Round-Corner Rib Heat Transfer Coefficient Measurements in a Square Channel, Journal of Turbomachinery 121(2) (1999) 272-280.
[106] R.G. Hibbs, S. Acharya, Y. Chen, D.E. Nikitopoulos, T.A. Myrum, Heat Transfer in a Two-Pass Internally Ribbed Turbine Blade Coolant Channel with Cylindrical Vortex Generators, Journal of Turbomachinery 120(3) (1998) 589-600.
[107] Y. Chen, D.E. Nikitopoulos, R. Hibbs, S. Acharya, T.A. Myrum, Detailed Mass Transfer Distribution in a Ribbed Coolant Passage with A 180 Degrees Bend, International Journal of Heat and Mass Transfer 43(8) (2000) 1479-1492.
[108] S. Acharya, R.G. Hibbs, Y. Chen, D.E. Nikitopoulos, Mass/Heat Transfer in a Ribbed Passage with Cylindrical Vortex Generators: The Effect of Generator-Rib Spacing, Journal of Heat Transfer 122(4) (2000) 641-652.
[109] C.W. Leung, T.T. Wong, S.D. Probert, Enhanced Forced-Convection from Ribbed or Machine-Roughened Inner Surfaces within Triangular Ducts, Applied Energy 69(2) (2001) 87-99.
[110] M. Taslim, H. Liu, A Combined Numerical and Experimental Study of Heat Transfer in a Roughened Square Channel with 45∘ Ribs, International Journal of Rotating Machinery 2005(1) (2005) 60-66.
[111] D. Luo, Forced Convection and Fluid Friction in a Horizontal Triangular Duct with Uniformly Ribbed or Grooved Internal Surfaces, The Hong Kong Polytechnic University, Hong Kong, 2006.
[112] A.P. Rallabandi, H.T. Yang, J.C. Han, Heat Transfer and Pressure Drop Correlations for Square Channels With 45 Deg Ribs at High Reynolds Numbers, Journal of Heat Transfer 131(7) (2009).
[113] G. Tanda, Effect of Rib Spacing on Heat Transfer and Friction in a Rectangular Channel with 45 Angled Rib Turbulators on One/Two Walls, International Journal of Heat and Mass Transfer 54(5) (2011) 1081-1090.
[114] M. Molki, A.R. Mostoufizadeh, Turbulent heat transfer in rectangular ducts with repeated-baffle blockages, International Journal of Heat and Mass Transfer 32(8) (1989) 1491-1499.
[115] Y.T. Yang, C.Z. Hwang, Calculation of turbulent flow and heat transfer in a porous-baffled channel, International Journal of Heat and Mass Transfer 46(5) (2003) 771-780.
[116] M.A. Habib, A.M. Mobarak, M.A. Sallak, E.A. Hadi, R.I. Affify, Experimental investigation of heat transfer and flow over baffles of different heights, Journal of Heat Transfer 116(2) (1994) 363-368.
[117] K.H. Ko, N.K. Anand, Use of porous baffles to enhance heat transfer in a rectangular channel, International Journal of Heat and Mass Transfer 46(22) (2003) 4191-4199.
[118] J.C. Han, J.S. Park, C.K. Lei, Heat Transfer and Pressure Drop in Blade Cooling Channels with Turbulence Promoters, Final Report Texas A&M Univ., College Station. Dept. of Mechanical Engineering. 1 (1984).
[119] L. Al-Hadhrami, J.C. Han, Effect of Rotation on Heat Transfer in Two-Pass Square Channels with Five Different Orientations of 45 Degrees Angled Rib Turbulators, International Journal of Heat and Mass Transfer 46(4) (2003) 653-669.
[120] J.H. Wagner, B.V. Johnson, R.A. Graziani, F.C. Yeh, Heat-Transfer in Rotating Serpentine Passages with Trips Normal to the Flow, Journal of Turbomachinery 114(4) (1992) 847-857.
[121] B.V. Johnson, J.H. Wagner, G.D. Steuber, F.C. Yeh, Heat-Transfer in Rotating Serpentine Passages with Trips Skewed to the Flow, Journal of Turbomachinery 116(1) (1994) 113-123.
[122] S. Fann, W.J. Yang, N.L. Zhang, Local Heat-Transfer in a Rotating Serpentine Passage with Rib-Roughened Surfaces, International Journal of Heat and Mass Transfer 37(2) (1994) 217-228.
[123] S. Dutta, J.C. Han, Y.M. Zhang, Influence of Rotation on Heat Transfer from a Two-Pass Channel with Periodically Placed Turbulence and Secondary Flow Promoters, International Journal of Rotating Machinery 1(2) (1995) 129-144.
[124] Y.M. Zhang, J.C. Han, J.A. Parsons, C.P. Lee, Surface Heating Effect on Local Heat-Transfer in a Rotating 2-Pass Square Channel with 60-Deg Angled Rib Turbulators, Journal of Turbomachinery-Transactions of the Asme 117(2) (1995) 272-280.
[125] J.A. Parsons, J.C. Han, Y. Zhang, Effect of Model Orientation and Wall Heating Condition on Local Heat Transfer in a Rotating Two-Pass Square Channel with Rib Turbulators, International Journal of Heat and Mass Transfer 38(7) (1995) 1151-1159.
[126] C.Y. Zhao, W.Q. Tao, Effect of Rib Angle Orientation on Local Mass Transfer Distribution around Sharp 180 Deg Turn with Rib-Turbulators Mounted in Entire Two-Pass Channels, Heat and Mass Transfer 32(5) (1997) 325-332.
[127] J. Schabacker, A. Boelcs, B. Johnson, PIV Investigation of the Flow Characteristics in an Internal Coolant Passage With 45 Deg Rib Arrangement, 1999.
[128] J. Schabacker, A. Bolcs, B.V. Johnson, PIV Investigation of the Flow Characteristics in an Internal Coolant Passage with 90 Degree Rib Arrangement, Third European Conference on Turbomachinery - Vols a and B (1999) 973-984.
[129] A. Murata, S. Mochizuki, T. Takahashi, Local Heat Transfer Measurements of an Orthogonally Rotating Square Duct with Angled Rib Turbulators, International Journal of Heat and Mass Transfer 42(16) (1999) 3047-3056.
[130] A. Murata, S. Mochizuki, Comparison Between Laminar and Turbulent Heat Transfer in a Stationary Square Duct with Transverse or Angled Rib Turbulators, International Journal of Heat and Mass Transfer 44(6) (2001) 1127-1141.
[131] A. Murata, S. Mochizuki, Large Eddy Simulation of Turbulent Heat Transfer in an Orthogonally Rotating Square Duct with Angled Rib Turbulators, Journal of Heat Transfer 123(5) (2001) 858-867.
[132] A. Murata, S. Mochizuki, Large Eddy Simulation of Turbulent Heat Transfer in a Rotating Two-Pass Smooth Square Channel with Sharp 180 Turns, International Journal of Heat and Mass Transfer 47(4) (2004) 683-698.
[133] A. Murata, S. Mochizuki, Aiding and Opposing Contributions of Centrifugal Buoyancy on Turbulent Heat Transfer in a Two-Pass Transverse-or Angled-Rib-Roughened Channel with Sharp 180 Turns, International Journal of Heat and Mass Transfer 47(17) (2004) 3721-3743.
[134] A. Murata, S. Mochizuki, Centrifugal Buoyancy Effect on Turbulent Heat Transfer in a Rotating Two-Pass Smooth Square Channel with Sharp 180-Deg Turns, International Journal of Heat and Mass Transfer 47(14) (2004) 3215-3231.
[135] R. Kiml, S. Mochizuki, A. Murata, Effects of Rib Arrangements on Heat Transfer and Flow Behavior in a Rectangular Rib-Roughened Passage: Application to Cooling of Gas Turbine Blade Trailing Edge, Journal of Heat Transfer 123(4) (2001) 675-681.
[136] R. Kiml, S. Mochizuki, A. Murata, M. Sulitka, Rib-Induced Secondary Flow Structures inside a High Aspect Ratio Trapezoidal Channel, Proceedings of the International Gas Turbine Congress, Tokyo, 2003.
[137] R. Kiml, A. Magda, S. Mochizuki, A. Murata, Rib-Induced Secondary Flow Effects on Local Circumferential Heat Transfer Distribution inside a Circular Rib-Roughened Tube, International Journal of Heat and Mass Transfer 47(6) (2004) 1403-1412.
[138] A. Murata, S. Mochizuki, Effect of Cross-Sectional Aspect Ratio On Turbulent Heat Transfer in an Orthogonally Rotating Rectangular Duct with Angled Rib Turbulators, International Journal of Heat and Mass Transfer 46(16) (2003) 3119-3133.
[139] T.M. Liou, G.Y. Dai, Pressure and Flow Characteristics in a Rotating Two-Pass Square Duct with 45-Deg Angled Ribs, Journal of Turbomachinery 126(1) (2004) 212-219.
[140] T.M. Liou, Y.S. Hwang, Y.C. Li, Flowfield and Pressure Measurements in a Rotating Two-Pass Duct with Staggered Rounded Ribs Skewed 45 Degrees to the Flow, Journal of Turbomachinery 128(2) (2006) 340-348.
[141] B. Lu, P.X. Jiang, Experimental and Numerical Investigation of Convection Heat Transfer in a Rectangular Channel with Angled Ribs, Experimental Thermal and Fluid Science 30(6) (2006) 513-521.
[142] M. Amro, B. Weigand, R. Poser, M. Schnieder, An Experimental Investigation of the Heat Transfer in a Ribbed Triangular Cooling Channel, International Journal of Thermal Sciences 46(5) (2007) 491-500.
[143] Y.H. Liu, M. Huh, J.C. Han, H.K. Moon, High Rotation Number Effect on Heat Transfer in a Triangular Channel with 45 Deg, Inverted 45 Deg, And 90 Deg Ribs, Journal of Heat Transfer 132(7) (2010) 071702.
[144] Y.I. Smulsky, V.I. Terekhov, N.I. Yarygina, Heat Transfer in Turbulent Separated Flow behind a Rib on the Surface of Square Channel at Different Orientation Angles Relative to Flow Direction, International Journal of Heat and Mass Transfer 55(4) (2012) 726-733.
[145] S.W. Chang, T.M. Liou, T.H. Lee, Heat Transfer and Pressure Drop Measurements of Rotating Rib-Roughened Parallelogram Channel, Journal of Thermophysics and Heat Transfer 26(1) (2012) 98-107.
[146] R. Goldstein, H. Cho, A Review of Mass Transfer Measurements Using Naphthalene Sublimation, Experimental Thermal and Fluid Science 10(4) (1995) 416-434.
[147] G.N. Xie, B. Sunden, W.H. Zhang, Comparisons of Pins/Dimples/Protrusions Cooling Concepts for a Turbine Blade Tip-Wall at High Reynolds Numbers, Journal of Heat Transfer 133(6) (2011).
[148] F.P. Incropera, A.S. Lavine, T.L. Bergman, D.P. DeWitt, Fundamentals of heat and mass transfer, Wiley2007.
[149] R.J. Adrian, Particle-Imaging Techniques for Experimental Fluid-Mechanics, Annual Review of Fluid Mechanics 23 (1991) 261-304.
[150] J. Westerweel, Fundamentals of Digital Particle Image Velocimetry, Measurement science and technology 8(12) (1997) 1379-1392.
[151] M. Raffel, C. Willert, J. Kompenhans, Particle Image Velocimetry: a Practical Guide, Springer, 1998.
[152] R.J. Adrian, Twenty Years of Particle Image Velocimetry, Experiments in Fluids 39(2) (2005) 159-169.
[153] A. Melling, Tracer Particles and Seeding for Particle Image Velocimetry, Measurement science and technology 8(12) (1997) 1406-1416.
[154] A.B. Basset, The Descent of a Sphere in a Viscous Liquid, Nature 83 (1910) 521-521.
[155] J. Hinze, Turbulence, McGraw-Hill, 1972.
[156] B.T. Chao, Motion of Spherical Gas Bubbles in a Viscous Liquid at Large Reynolds Numbers, Physics of Fluids 5(1) (1962) 69-79.
[157] Hjelmfel.At, L.F. Mockros, Motion of Discrete Particles in a Turbulent Fluid, Applied Scientific Research 16(2) (1966) 149-&.
[158] A. Rogalski, K. Chrzanowski, Infrared devices and techniques, Optoelectronics Review 10(2) (2002) 111-136.
[159] W. Wien, Temperatur und entropie der strahlung, Annalen der Physik 288(5) (1894) 132-165.
[160] W. Thielicke, E. Stamhuis, PIVlab–towards User-Friendly, Affordable and Accurate Digital Particle Image Velocimetry in MATLAB, Journal of Open Research Software 2(1) (2014).
[161] S.W. Chang, T.M. Liou, T.H. Lee, Thermal Performance Comparison between Radially Rotating Ribbed Parallelogram Channels With and Without Dimples, International Journal of Heat and Mass Transfer 55(13-14) (2012) 3541-3559.
[162] R.D. Keane, R.J. Adrian, Optimization of Particle Image Velocimeters: II. Multiple Pulsed Systems, Measurement science and technology 2(10) (1991) 963-974.
[163] J.H. Kim, T.W. Simon, R. Viskanta, Journal of Heat Transfer Policy on Reporting Uncertainties in Experimental Measurements and Results, Journal of Heat Transfer 115(1) (1993) 5-6.
[164] S.J. Kline, F.A. McClintock, Describing Uncertainties in Single-Sample Experiments, Mechanical engineering 75(1) (1953) 3-8.
[165] D. Dynamics, Flow Manager Software and Introduction to PIV Instrumentation. <http://www.dantecdynamics.com/measurement-principles-of-piv>, 2002).
[166] M.F. Modest, Radiative heat transfer, Academic press2013.
[167] FLIR, FLIR T420 & T440 Datasheet. <http://www.flir.com/uploadedFiles/Thermography_USA/Products/Product_Literature/flir-t420-t440-datasheet.pdf>, 2012).
[168] Kyowa, WGA-200A Series Datasheet. <http://www.kyowa-ei.com/eng/download/support/download/catalog/s_wga-200a_series_catalog_1402_01_eng.pdf>).
[169] G.Y. Dai, Rotating Effects on Fluid Flows a Simulated Turbine Blade Internal Cooling Passage with 45-Deg Rib Arrangements, National Tsing Hua University, 2003.
[170] Y.J. Jang, H.C. Chen, J.C. Han, Computation of Flow and Heat Transfer in Two-Pass Channels with 60 Deg Ribs, Journal of Heat Transfer 123(3) (2001) 563-575.
[171] A. Lin, Influence of Entrance Geometry on Flow Field and Heat Transfer Performance in Stationary Two-Pass Smooth Parallelogram Channels, National Tsing Hua University, 2016.
[172] B.R. Munson, D.F. Young, T.H. Okiishi, Fundamentals of Fluid Mechanics, New York1990.
[173] M.Y. Chen, Rotating Effects on Heat and Fluid Flows in a Simulated Turbine Blade Internal Cooling Passage with Various Rib Arrangements, National Tsing Hua University, Hsinchu, Taiwan, 2002.
[174] F. Dittus, L. Boelter, University of California publications on engineering, University of California Publications in Engineering 2 (1930) 371.
[175] H. Blasius, Das Ähnlichkeitsgesetz bei Reibungsvorgängen in Flüssigkeiten, Mitteilungen über Forschungsarbeiten auf dem Gebiete des Ingenieurwesens, Springer1913, pp. 1-41.
[176] Y.M. Hsieh, Effect of Number of Slat on Flow Features in a Two-Pass Square Channel Mounted with Louver-Type Perturbators, National Tsing Hua University, Hsinchu, Taiwan, 2017
連結至畢業學校之論文網頁點我開啟連結
註: 此連結為研究生畢業學校所提供,不一定有電子全文可供下載,若連結有誤,請點選上方之〝勘誤回報〞功能,我們會盡快修正,謝謝!
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top
無相關期刊