跳到主要內容

臺灣博碩士論文加值系統

(18.97.14.80) 您好!臺灣時間:2025/01/26 01:14
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

: 
twitterline
研究生:陳治綸
研究生(外文):CHEN,CHIH-LUN
論文名稱:烘乾箱PC-based量測儀器
論文名稱(外文):PC-based instrument for Drying oven
指導教授:洪博雄洪博雄引用關係
指導教授(外文):Hong,Boe-Shong
口試委員:黃勤鎰徐旭華
口試委員(外文):Huang,Chin-IShyu,Shiuh-Hwa
口試日期:2020-07-24
學位類別:碩士
校院名稱:國立中正大學
系所名稱:機械工程系研究所
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2020
畢業學年度:108
語文別:中文
論文頁數:30
中文關鍵詞:客製化設備Matlab人機介面訊號擷取器
外文關鍵詞:Customized equipmentMatlabMan-machine interfaceSignal extractor
相關次數:
  • 被引用被引用:0
  • 點閱點閱:280
  • 評分評分:
  • 下載下載:37
  • 收藏至我的研究室書目清單書目收藏:0
本研究因應烘乾箱廠商所需的量測需求,建立一套以電腦為主的客製化量測設備。整體研究可分為找尋量測設備、資料擷取處理、建立電腦端使用者介面三個部分。依廠商所需量測的參數(靜壓、風速、溫度)找尋相對應的量測設備後,透過研華科技的USB-4711A訊號擷取器將資料收集後透過 MATLAB 所撰寫的人機介面顯示數據並將其儲存。建立設備的同時也設計電源供應電路以及後續所需的放大器電路,並以3D印表機印製外殼,以提升整套設備的實用性。透過 MATLAB、USB-4711A、電路設計程式及3D印表機等結合,設計出一套低成本、高整合性的儀表量測設備。
This research establishes a set of computer-based customized measuring equipment according to the measurement requirements of manufacturer. The overall research can be divided into three parts: searching measuring equipment, data acquisition and processing, and establishing user interface on computer . After finding the corresponding measuring equipment according to the measured parameters (static pressure, wind speed, temperature) required by the manufacturer, data will collected by ADVANTECH Technologies USB-4711A signal extractor and displayed through the man-machine interface written in MATLAB and stored. The power supply circuit and subsequent amplifier circuit are designed as well as the equipment is built, and the housing is printed on a 3D printer to improve the practicability of the entire equipment. Through the combination of MATLAB, USB-4711A, circuit design program and 3D printer, a low-cost and highly integrated measurement system is designed.
致謝 I
摘要 II
Abstract III
圖目錄 VI
表目錄 VIII
第一章 緒論 1
1.1 研究動機與目的 1
1.2 文獻回顧 2
1.3 本文貢獻 2
第二章 系統軟硬體介紹 3
2.1 MATLAB 3
2.2 風速感測 3
2.3 壓差感測 5
2.4 溫度感測 6
2.5 資料擷取器 8
2.6 Altium Designer 9
2.7 Solidworks 9
2.8 烘乾箱設備 10
第三章 實驗流程與架構 11
3.1 實驗規劃與流程 11
第四章 實驗架構設計 12
4.1 實驗前置作業 12
4.2 電源供應電路 13
4.3 熱電偶及放大器電路 15
4.4 MATLAB介面設計 18
第五章 實驗結果 21
5.1 感測器測試結果 21
第六章 未來展望 28
參考文獻 29


[1]鄧雅才,Matlab為介面之USB整合式儀器,碩士論文,國立中正大學機械工程學系,2019
[2]Keysight Technolgy-示波器基本原理,2017
http://literature.cdn.keysight.com/litweb/pdf/5989-8064ZHA.pdf
[3]Digitimes-智慧製造大趨勢:經驗傳承、資訊創新是關鍵,廖家宜,2017
[4]張智星(民100)。Matlab在工程上的應用。新北市:高立。
[5]唐龍成,以dsPIC30F4011晶片為核心之韌體式量測儀器,碩士論文,國立中正大學機械工程學系,2016
[6]宇田控制,產品型錄eYc FT34/35風速傳送器。2019年9月15號
https://www.yuden.com.tw/eyc-fts34-35-air-velocity-transmitter.html
[7]維一企業,DPT系列壓差傳感器。2019年9月15號
https://www.27223234.com.tw/product/honeywell-dpt-series-differential-pressure-transmitter/
[8]路昌TM902C溫度計,2019年10月1號
http://www.luchina.cn/wenduji/238.html
[9]研華科技 Advantech,USB-4711A,2019年06月27號
http://www.advantech.com/products/1-2mlkno/usb-4711a/mod_16cb666d-62ee-4c15-bf5f-ea49f61093cf
[10]洪維恩(民95)。Matlab7程式設計。台北市:旗標。
[11]喬群機械工業有限公司,單層烘乾箱,2020年5月18號
https://www.chaochiun.com/tw/product/34/43
[12]Mathworks,lowpass filter,2020年5月2號
https://ww2.mathworks.cn/help/signal/ref/lowpass.html

[13]Digi-Key,TL074CN datasheet,2020年6月1號
https://www.digikey.tw/product-detail/zh/stmicroelectronics/TL074CN/497-2205-5-ND/599651?WT.z_cid=ref_neda_dkc_buynow_ihstest&utm_source=ecia&utm_medium=aggregator&utm_campaign=ihstest&source=Datasheets360

QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top