跳到主要內容

臺灣博碩士論文加值系統

(44.201.99.222) 您好!臺灣時間:2022/12/03 14:44
字體大小: 字級放大   字級縮小   預設字形  
回查詢結果 :::

詳目顯示

我願授權國圖
: 
twitterline
研究生:林宗融
研究生(外文):Lin, Tsung-Rong
論文名稱:將水霧與下游區域的電漿束混合以提高•OH的強度用於生物應用上
論文名稱(外文):Enhancing the •OH Generation by Mixing Water Aerosol with Plasma at Downstream Region for Biological Applications
指導教授:鄭雲謙
指導教授(外文):Cheng, Yun-Chien
口試委員:吳宗信劉耀先
口試委員(外文):Wu, Jong-ShinnLiu, Yao-Hsien
口試日期:2020-01-09
學位類別:碩士
校院名稱:國立交通大學
系所名稱:機械工程系所
學門:工程學門
學類:機械工程學類
論文種類:學術論文
論文出版年:2020
畢業學年度:108
語文別:中文
論文頁數:93
中文關鍵詞:常壓電漿水霧混合腔體氫氧根離子殺菌
外文關鍵詞:atmospheric pressure plasmawater aerosolmixing chamberhydroxyl radical (·OH)sterilization
相關次數:
  • 被引用被引用:0
  • 點閱點閱:95
  • 評分評分:
  • 下載下載:0
  • 收藏至我的研究室書目清單書目收藏:0
中文摘要 i
Abstract iii
目錄 vii
圖目錄 x
表目錄 xiii
第一章、 緒論 1
1.1 研究背景 1
1.1.1 電漿簡介與應用 1
1.1.2 介電質屏蔽放電 (Dielectric barrier discharge) 2
1.1.3 電漿殺菌簡介 2
1.2 文獻回顧 3
1.2.1 低溫常壓電漿殺菌 3
1.2.2 在潮濕環境下進行低溫常壓電漿殺菌 4
1.2.3 增加電漿束中•OH的方法 5
1.2.3.1 增加環境濕度 5
1.2.3.2 在工作氣體中加入水氣 5
1.2.3.3 在潮濕表面進行殺菌 6
1.2.4 水霧電漿殺菌 6
1.3 研究動機與目標 7
1.4 論文架構 7
第二章、 實驗原理與檢測儀器 9
2.1 電漿生成原理 9
2.2 電漿殺菌原理 10
2.3 實驗量測系統與分析儀器 12
2.3.1 霧化系統 (Atomizer System) 12
2.3.2 霧化粒徑分析系統 (Malvern Spraytec) 13
2.3.3 對-苯二甲酸(TA)測試 14
2.3.4 強化電荷偶合元件元件相機 (ICCD) 15
第三章、 實驗方法 18
3.1 實驗設置及方法 19
3.2 電漿與水霧混合腔體 19
3.3 雷諾數與渦漩度計算 28
3.3.1 雷諾數 (Reynolds Number) 28
3.3.2 渦漩數 (Swirl Number) 30
3.4 模擬軟體 Ansys-Workbench 32
3.4.1 建構模型 32
3.4.2 建立流場網格 33
3.4.3 參數設定 34
3.5 實驗設備 35
3.5.1 低溫常壓氬氣水霧電漿系統 35
3.5.2 電源供應器 37
3.5.3 氣體管路系統 37
3.6 實驗分析儀器與方法 39
3.6.1 對-苯二甲酸(TA)測試 39
3.6.2 相增強電荷耦合元件(ICCD) 43
3.6.3 霧化粒徑分析系統 (Malvern Spraytec) 43
3.7 細菌樣本之製備 45
3.8 殺菌實驗流程 50
第四章、 實驗結果與討論 52
4.1 水霧粒徑大小與消耗量分析 52
4.1.1 霧化器入口流量對水霧粒徑大小的影響(霧化器出口3 cm) 52
4.1.2 霧化器入口流量對水霧粒徑大小的影響(霧化器出口100 cm) …..…………………………………………………………….54
4.1.3 霧化器出口距離對水霧粒徑大小的影響 57
4.1.4 水霧消耗量量測 58
4.2 ANSYS模擬結果 59
4.2.1 混合腔體的影響 62
4.2.2 水霧流量的影響 62
4.2.3 水霧進入混合腔體角度的影響 62
4.3 ICCD結果分析 62
4.3.1 ICCD圖片結果分析 62
4.3.1.1 有加水霧 vs 無水霧 63
4.3.1.2 四種混合腔體的比較 65
4.3.2 最強區域分析 66
4.3.3 最強列分析 70
4.3.4 距離混合腔體出口1 mm的列總和分析 71
4.3.5 ICCD結果總整理 73
4.4 TA Test結果分析 73
4.5 殺菌結果分析 78
第五章、 結論與未來研究內容 82
5.1 結論 82
5.2 未來研究內容 83
參考文獻 84
附錄 89
[1] G. I. Font, "Boundary Layer Control with Atmospheric Plasma Discharges," AIAA Journal, vol. 44, pp. 1572-1578, 2006/07/01 2006.
[2] G. Da Ponte, E. Sardella, F. Fanelli, R. d’Agostino, and P. Favia, "Trends in surface engineering of biomaterials: atmospheric pressure plasma deposition of coatings for biomedical applications," Eur. Phys. J. Appl. Phys., vol. 56, p. 24023, 2011.
[3] M. Laroussi, "The Biomedical Applications of Plasma: A Brief History of the Development of a New Field of Research," IEEE Transactions on Plasma Science, vol. 36, pp. 1612-1614, 2008.
[4] 沈柏村, "以氦氣為主的平板型常壓電漿束特性之實驗研究," 碩士論文, 國立交通大學, 民國100年.
[5] K. Shimizu, "Study of Sterilization and Disinfection in Room Air by Using Atmospheric Microplasma. Pharmaceutica Analytica Acta, Special issue title : PK/PD," Antifungal and Antibacterial, vol. 11, pp. PAA-11-372, 2011 2011.
[6] G. Fridman, A. Shereshevsky, M. M. Jost, A. D. Brooks, A. Fridman, A. Gutsol, et al., "Floating Electrode Dielectric Barrier Discharge Plasma in Air Promoting Apoptotic Behavior in Melanoma Skin Cancer Cell Lines," Plasma Chemistry and Plasma Processing, vol. 27, pp. 163-176, April 01 2007.
[7] R. Alhabshan, D. Belyea, M. Stepp, J. Barratt, and S. Grewal, "Effects of in-vivo application of cold atmospheric plasma on corneal wound healing in New Zealand white rabbits," Int J Ophthalmic Pathol 2, vol. 3, p. 2, 2013.
[8] J. Ehlbeck, U. Schnabel, M. Polak, J. Winter, T. Von Woedtke, R. Brandenburg, et al., "Low temperature atmospheric pressure plasma sources for microbial decontamination," Journal of Physics D: Applied Physics, vol. 44, p. 013002, 2010.
[9] S. Veerabadran and I. M. Parkinson, "Cleaning, disinfection and sterilization of equipment," Anaesthesia & intensive care medicine, vol. 11, pp. 451-454, 2010.
[10] G. F. Reddish, Antiseptics, Disinfectants, Fungicides, and Chemical Physical Sterilization: The United States Of America, 1954.
[11] Z. Machala, B. Tarabova, K. Hensel, E. Spetlikova, L. Sikurova, and P. Lukes, "Formation of ROS and RNS in Water Electro-Sprayed through Transient Spark Discharge in Air and their Bactericidal Effects," Plasma Processes and Polymers, vol. 10, pp. 649-659, 2013.
[12] C. Cheng, J. Shen, D.-Z. Xiao, H.-B. Xie, Y. Lan, S.-D. Fang, et al., "Atmospheric pressure plasma jet utilizing Ar and Ar/H 2 O mixtures and its applications to bacteria inactivation," Chinese Physics B, vol. 23, p. 075204, 2014.
[13] M. Tanino, X. Wang, K. Takashima, S. Katsura, and A. Mizuno, "Sterilization using dielectric barrier discharge at atmospheric pressure," in Fourtieth IAS Annual Meeting. Conference Record of the 2005 Industry Applications Conference, 2005., 2005, pp. 784-788 Vol. 2.
[14] J. Guo, K. Huang, and J. Wang, "Bactericidal effect of various non-thermal plasma agents and the influence of experimental conditions in microbial inactivation: A review," Food Control, vol. 50, pp. 482-490, 2015.
[15] M. Laroussi and F. Leipold, "Evaluation of the roles of reactive species, heat, and UV radiation in the inactivation of bacterial cells by air plasmas at atmospheric pressure," International Journal of Mass Spectrometry, vol. 233, pp. 81-86, 2004/04/15/ 2004.
[16] M. Yusupov, A. Bogaerts, S. Huygh, R. Snoeckx, A. C. T. van Duin, and E. C. Neyts, "Plasma-Induced Destruction of Bacterial Cell Wall Components: A Reactive Molecular Dynamics Simulation," The Journal of Physical Chemistry C, vol. 117, pp. 5993-5998, 2013/03/21 2013.
[17] X. Deng, J. Shi, and M. G. Kong, "Physical mechanisms of inactivation of Bacillus subtilis spores using cold atmospheric plasmas," 2006.
[18] C. Huang, Q. Yu, F.-h. Hsieh, and Y. Duan, "Bacterial Deactivation Using a Low Temperature Argon Atmospheric Plasma Brush with Oxygen Addition," Plasma Processes and Polymers, vol. 4, pp. 77-87, 2007.
[19] S. J. Kim, T. H. Chung, S. H. Bae, and S. H. Leem, "Bacterial inactivation using atmospheric pressure single pin electrode microplasma jet with a ground ring," Applied Physics Letters, vol. 94, p. 141502, 2009.
[20] H. Eto, Y. Ono, A. Ogino, and M. Nagatsu, "Low-temperature sterilization of wrapped materials using flexible sheet-type dielectric barrier discharge," Applied Physics Letters, vol. 93, p. 221502, 2008.
[21] Y. Kikuchi, M. Miyamae, M. Nagata, and N. Fukumoto, "Effects of environmental humidity and temperature on sterilization efficiency of dielectric barrier discharge plasmas in atmospheric pressure air," Japanese Journal of Applied Physics, vol. 50, p. 01AH03, 2011.
[22] S. Patil, T. Moiseev, N. Misra, P. Cullen, J. Mosnier, K. Keener, et al., "Influence of high voltage atmospheric cold plasma process parameters and role of relative humidity on inactivation of Bacillus atrophaeus spores inside a sealed package," Journal of Hospital Infection, vol. 88, pp. 162-169, 2014.
[23] V. Sinha, J. Williams, J. Crowley, and J. Lelieveld, "The Comparative Reactivity Method–a new tool to measure total OH Reactivity in ambient air," Atmospheric Chemistry and Physics, vol. 8, pp. 2213-2227, 2008.
[24] P. Bruggeman, T. Verreycken, M. A. Gonzalez, J. L. Walsh, M. G. Kong, C. Leys, et al., "Optical emission spectroscopy as a diagnostic for plasmas in liquids: opportunities and pitfalls," Journal of Physics D: Applied Physics, vol. 43, p. 124005, 2010.
[25] Y. Nakagawa, R. Ono, and T. Oda, "Density and temperature measurement of OH radicals in atmospheric-pressure pulsed corona discharge in humid air," Journal of Applied Physics, vol. 110, p. 073304, 2011.
[26] N. Srivastava and C. Wang, "Effects of water addition on OH radical generation and plasma properties in an atmospheric argon microwave plasma jet," Journal of Applied Physics, vol. 110, p. 053304, 2011.
[27] C. Cheng, S. Jie, X. De-Zhi, X. Hong-Bing, L. Yan, F. Shi-Dong, et al., "Atmospheric pressure plasma jet utilizing Ar and Ar/H2O mixtures and its applications to bacteria inactivation," Chinese Physics B, vol. 23, p. 075204, 2014.
[28] M. Tanino, W. Xilu, K. Takashima, S. Katsura, and A. Mizuno, "Sterilization using dielectric barrier discharge at atmospheric pressure," Int J Plasma Environ Sci Technol, vol. 1, pp. 108-113, 2007.
[29] Z. Machala, B. Tarabova, K. Hensel, E. Spetlikova, L. Sikurova, and P. Lukes, "Formation of ROS and RNS in Water Electro‐S prayed through Transient Spark Discharge in Air and their Bactericidal Effects," Plasma Processes and Polymers, vol. 10, pp. 649-659, 2013.
[30] P. Attri, Y. H. Kim, D. H. Park, J. H. Park, Y. J. Hong, H. S. Uhm, et al., "Generation mechanism of hydroxyl radical species and its lifetime prediction during the plasma-initiated ultraviolet (UV) photolysis," Scientific reports, vol. 5, p. 9332, 2015.
[31] B. Eliasson and U. Kogelschatz, "Nonequilibrium volume plasma chemical processing," IEEE Transactions on Plasma Science, vol. 19, pp. 1063-1077, 1991.
[32] M. Moisan, J. Barbeau, S. Moreau, J. Pelletier, M. Tabrizian, and L. H. Yahia, "Low-temperature sterilization using gas plasmas: a review of the experiments and an analysis of the inactivation mechanisms," International journal of Pharmaceutics, vol. 226, pp. 1-21, 2001.
[33] 陳柏賢, "電漿技術於生物感測器表面改質與高分子材料表面殺菌之研究," 碩士, 材料科學與製造研究所, 中國文化大學, 台北市, 2004.
[34] M. Moisan, J. Barbeau, M.-C. Crevier, J. Pelletier, N. Philip, and B. Saoudi, "Plasma sterilization. Methods and mechanisms," Pure and applied chemistry, vol. 74, pp. 349-358, 2002.
[35] "Model 3076 Constant Output Atomizer," ed: Revision J, 2005.
[36] S. Kanazawa, T. Furuki, T. Nakaji, S. Akamine, and R. Ichiki, "Measurement of OH radicals in aqueous solution produced by atmospheric-pressure LF plasma jet," Department of electrical and electronic engineering, Oita University, Japan, 2012.
[37] 吳佳華, "利用低溫常壓氦氣電漿束搭配食鹽水進行牙齒美白之研究," 碩士, 機械工程系所, 國立交通大學, 新竹市, 2016.
[38] O. Optics. Available: https://oceanoptics.com/
[39] S.-y. Jin, Y.-z. Liu, W.-z. Wang, Z.-m. Cao, and H. S. Koyama, "Numerical Evaluation of Two-Fluid Mixing in a Swirl Micro-Mixer," Journal of Hydrodynamics, vol. 18, pp. 542-546, October 01 2006.
[40] D. Brone and F. Muzzio, "Enhanced mixing in double-cone blenders," Powder Technology, vol. 110, pp. 179-189, 2000.
[41] E. ToolBox. (2013). Reynolds Number. Available: https://www.engineeringtoolbox.com/reynolds-number-d_237.html
[42] K. Gersten, Boundary-layer theory: Springer, 2017.
[43] E. Paccagnella, F. Barato, D. Pavarin, and A. M. Karabeyoglu, "Scaling of Hybrid Rocket Motors with Swirling Oxidizer Injection-Part 2," in 52nd AIAA/SAE/ASEE Joint Propulsion Conference, 2016, p. 4750.
[44] H.-H. Lee, Finite Element Simulations with ANSYS Workbench 18: SDC publications, 2018.
電子全文 電子全文(網際網路公開日期:20250108)
連結至畢業學校之論文網頁點我開啟連結
註: 此連結為研究生畢業學校所提供,不一定有電子全文可供下載,若連結有誤,請點選上方之〝勘誤回報〞功能,我們會盡快修正,謝謝!
QRCODE
 
 
 
 
 
                                                                                                                                                                                                                                                                                                                                                                                                               
第一頁 上一頁 下一頁 最後一頁 top
無相關期刊