臺灣博碩士論文加值系統

寢具的選擇與睡眠品質有直接的關係，並且在一床組中，於床上再放置床墊使用以提升舒適性是近年常見的趨勢，因此對於床墊舒適性的研究益發重要。
本研究共招集40位健康男性受試者，針對硬、中、軟三種材質軟硬度及3、5、7、10公分四種厚度組合之床墊進行人因評估，透過蒐集人體平躺於不同床墊時之全身壓力分佈、全身溫度分佈、肌肉活動度、微氣候溫濕度、脊椎角度等各式生理訊號，搭配主觀問卷之分析，以得到最佳之軟硬度與厚度配置組合。
研究結果顯示在軟硬度方面，硬床墊之全身壓力分佈在各部位皆較軟床墊為高，全身溫度分佈則普遍以中床墊溫度為高，且與躺臥時間成正比。微氣候溫度以中及軟床墊為高，也與時間成正比，但濕度則與時間成反比。肌肉活動度(EMG)以軟床墊在斜方肌、硬床墊在股二頭肌可使EMG最低。脊椎斜率有顯著差異的則為胸椎之T1-T4、T4-T6與T6-T8三區段，以硬床墊之斜率最小而能使脊椎最為平直。厚度方面，與各部位壓力值的關係並無明顯的規律，但溫度分佈則是厚床墊之溫度較薄床墊高，微氣候濕度則以5公分之床墊較低，EMG以10公分的床墊在股二頭肌、5及7公分在腓腸肌為最低，脊椎斜率則以3公分床墊在T12-L1及L1-L4之斜率最小。主觀問卷結果方面，受試者主觀感受為硬床墊最硬而軟床墊最軟、支撐性以硬床墊最佳而軟床墊最差，服貼性則是軟床墊最佳而硬床墊最差。最後，在本研究所選用之12張床墊中，綜合各項目之整體結果做一比較與排序，發現以3或7公分的軟床墊與3公分的中床墊在各指標皆有不錯的表現，為整體而言最佳之軟硬度x厚度配置組合。
本研究之結果將提供業界各種配置組合床墊實際使用時之各項生理數據，並針對各部位之需要提供未來床墊設計之參考，以利後續人因床墊之設計與發展。

The selection of a bedding system has direct relationship with sleeping quality. Putting a mattress topper on bed in use is also a common practice to increase sleeping comfort. Thus, the ergonomic study of a mattress topper is an important issue.
Forty healthy male subjects were recruited in this study. The experiment involves a combination of 3 different firmness (firm, medium, soft) and 4 thickness (3, 5, 7, 10 cm) levels. For each subject, pressure distribution, temperature distribution, microclimate, electromyography, spinal posture, accompany with subjective ratings were collected to determine the optimal firmness and thickness mattress topper combination.
The results showed that the firm mattress toppers had higher pressure in every position. The medium ones also had higher temperatures and it had an increasing trend with time. The microclimate temperature was higher on medium and soft toppers, and it was also proportional to time. But the microclimate humidity was inversely proportional to time. The electromyography of trapezius was lower on soft ones, and the EMG of biceps femoris was lower on firm ones. The slope of spine was lowest on firm ones at T1-T4, T4-T6 and T6-T8. The thick mattress toppers had higher temperatures. The humidity was the lowest at 5 cm, and the slope of spine was smallest at 3 cm. Subjective ratings revealed that the firm mattress toppers were perceived as the firmest and most supportive, while the soft ones had the greatest conformity. Finally, among all 12 combinations, 3 or 7 cm soft and 3 cm medium mattress toppers showed better performance in most physiological indexes, and was considered as the preferred combinations.

摘要 I
Abstract II
誌謝 III
表目錄 VI
圖目錄 IX
第一章、緒論 1
1.1研究背景 1
1.2研究動機 2
1.3研究目的 3
1.4研究流程 4
第二章、文獻探討 5
2.1 現有床組之分析 5
2.1.1 寢具之定義與功能 5
2.1.2 床之現有產品介紹 6
2.1.3 床墊之現有產品介紹 7
2.2 專利探討 12
2.3 文獻回顧 18
2.4 小結 22
第三章、研究方法 23
3.1 受測者資料 23
3.2 實驗設計 24
3.3 自變項 26
3.4 應變項 27
3.4.1 主觀問卷 29
3.5 儀器與設備 32
3.5.1 恆溫恆濕室 32
3.5.2 人體壓力分佈量測系統 32
3.5.3 溫度分佈分析系統 33
3.5.4 肌肉活動度量測系統 34
3.5.5 小型溫濕度感應器 35
3.5.6 反光球 36
3.6 實驗流程 37
3.6.1 脊椎角度數據分析 42
3.7 統計方法 43
第四章、研究結果 44
4.1 全身壓力分佈 44
4.2 全身溫度分佈 54
4.3 微氣候 65
4.4 肌肉活動度 79
4.5 脊椎角度 85
4.6 主觀問卷 90
4.7 綜合比較 96
4.8 討論 101
第五章、結論與建議 108
5.1 結論 108
5.2 建議 111
參考文獻 112
附錄 主觀評比問卷 117

1. A+醫學百科 (2011)，生理學/體溫。取自http://cht.a-hospital.com/w/%E7%94%9F%E7%90%86%E5%AD%A6/%E4%BD%93%E6%B8%A9#.UcfZJzvfCSo
2. LAKA《竹碳+波浪》環保記憶床墊。取自http://buy.yahoo.com.tw/gdsale/gdsale.asp?gdid=2466062
3. LooCa絲光緞彩10cm記憶床墊。取自http://buy.yahoo.com.tw/gdsale/gdsale.asp?gdid=1930991&sw=c6ed7c84fbf34ed4
4. 行政院衛生署 (2002)，國人肥胖定義及處理原則。2013年6月13日取自http://www.doh.gov.tw/CHT2006/DM/DM2_p01.aspx?class_no=25&level_no=1&doc_no=32
5. 于博芮、戴玉慈 (1999)，壓瘡預防—減壓床墊之比較與護理應用。護理雜誌雙月刊，頁33-39。
6. 王立主 (1991)，舒適性及其評估方法。紡織品舒適性說明會(一)，中國紡織工業研究中心，頁2-15。
7. 李宇宙 (2000)，睡眠醫學。台北市，健康世界出版社。
8. 李莉、申利明、周敏 (2009)，基于体压分布的海绵厚度对床垫舒适性影响。西北林学院学报， 24(6)，頁150-153。
9. 李莉 (2010)，基于人体工程学的海绵类型软床垫舒适性研究。西北林学院学报，25(003)，頁179-181。
10. 原田隆司 (1996)，衣服的快適性和感覺計測。纖維製品消費科學，日本，36，頁24。
11. 徐筱琪 (2001)，國人空調舒適度調查研究。冷凍與空調，10，頁168-172。
12. 康錦華，張冠諒，周有禮 (1991)，人體臥姿介面壓力測量－壓瘡預防方法之比較、檢討、評估。中華家醫誌，1 (2)，頁100-107。
13. 莊佩宜 (2011)，寢具情境氛圍影響消費者購買評估與購後評估之研究。淡江大學企業管理學系在職專班碩士論文。
14. 陳崇賢，陳昭源，林忠順 (2010)，失眠之評估與治療。家庭醫學與基層治療，25 (3)，頁92-99。
15. 陳德鴻、陳婉萍 (2011)，衣物之吸濕、透濕與透氣特性對人員生理、心理物理與主觀舒適性之影響。國科會計畫結案報告。
16. 黃文俐 (2002)，影響某完全中學學生睡眠品質之相關因素研究。臺灣師範大學衛生教育學系碩士論文。
17. 黃鼎豪，邱文科，林榮泰 (2006)，以表面壓力與主觀舒適度探討不同類型床墊之特性。第13屆中華民國人因工程學會年會暨研討會論文集，義守大學。
18. 蔡哲明 (2006)，床墊軟硬度與人體脊椎曲度對躺姿下脊椎應力之影響。義守大學生物醫學工程學系碩士論文。
19. American Society of Heating, Refrigerating and Air-Conditioning Engineers Inc., ASHRAE (2004) Standard 55: Thermal environmental conditions for human occupancy, American Society of Heating, Refrigeration and Air-conditioning Engineers, Atlanta.
20. Bader, G. and Engdal, S. (2000). The influence of bedfirmness on sleep quality. Applied Ergonomics, 31(5), 487–497.
21. Borg, G. (1998) Borg's perceived exertion and pain scales. Human Kinetics: Champaign, IL, 1998.
22. Buckle, P. and Fernandes, A. (1998). Mattress evaluation- assessment of contact pressure, comfort and discomfort. Applied Ergonomics, 29(1), 35-39.
23. Cram, J. R., Kasman, G. S., Holtz, J. (1998). Introduction to surface EMG. Maryland: Aspen Publishers, Gaithersburg.
24. Defloor, T. (2000). The Effect of Position and Mattress on Interface Pressure. Applied Nursing Research, 13(1), 2-11.
25. DeVocht, J. W., Wilder, D. G., Bandstra, E. R., Spratt, K. F. (2006). Biomechanical evaluation of four different mattresses. Applied Ergonomics, 37, 297-304.
26. Haex, B., Vander Sloten, J., & Van Audekercke, R. (1996). Required stiffness distribution in a mattress for an optimal curvature of the human spine during bedrest. Engineering in Medicine and Biology Society, 1996. Bridging Disciplines for Biomedicine. In proceedings of the 18th Annual International Conference of the IEEE, Vol. 2, pp. 495-496, Amsterdam.
27. Hagg, G.M., Kadefors, R. (1996). EMG alterations at sustained contractions with special emphasis on applications in ergonomics. In: Kumar, S., Mital, A. (Eds.), Electromyography in Ergonomics. London, UK, Taylor & Francis, 1-177.
28. Hardy, J.D., DuBois, E. F. (1938). The technic of measuring radiation and convection. Journal of Nutrition 15, 461-475.
29. Huysmans, T., Haex, B., De Wilde, T., Van Audekercke, R., Vander Sloten, J., Van der Perre, G. (2006). A 3D shape model for the evaluation of the alignment of the spine during sleeping. Gait & Posture, 24(1), 54-61.
30. Jacobson, B. H., Gemmel, H. A., Hayes, B. M., Altena, T. S. (2000). Effectiveness of a selected bedding system on quality of sleep, low back pain, shoulder pain, and spine stiffness. Journal of Manipulative and Physiological Therapeutics, 25(2), 88-92.
31. Kovacs, F. M., Abraira, V., Peña A., Martín-Rodríguez, J. G., Sánchez-Vera, M., Ferrer, E., Ruano, D., Guillén, P., Gestoso, M., Muriel, A., Zamora, J., Real, M. G. D., Mufraggi, N. (2003). Effect of firmness of mattress on chronic non-specific low-back pain: randomised, double-blind, controlled, multicentre trial. The Lancet. 362, 1599-1604.
32. Kroemer, K. H. (2009). Fitting the human: Introduction to ergonomics. Boca Raton, FL: CRC Press, 278.
33. Lahm, R. and Iaizzo, P. R. (2002). Physiologic responses during rest on a sleep system at varied degrees of firmness in a normal population. Ergonomics, 45(11), 798-815.
34. Lee, H. and Park, S. (2006). Quantitative effects of mattress types (comfortable vs. uncomfortable) on sleep quality through polysomnography and skin temperature. International Journal of Industrial Ergonomics, 36, 943–949.
35. López-Torres, M., Porcar, R., Solaz, J., Romero, T. (2008). Objective firmness, average pressure and subjective perception in mattresses for the elderly. Applied Ergonomics, 39, 123-130.
36. Nachemson, A. and Elfstrom, G. (1970). Intravital dynamic pressure measurements in lumbar discs. A study of common movements, maneuvers and exercises. Scandinavian Journal of Rehabilitation Medicine, 1, 1–40.
37. Park, S., Kim J., Kim C. (2009). Comfort Evaluation and Bed Adjustment According to Sleeping Positions. Human Factors and Ergonomics in Manufacturing & Service Industries, 19(2), 145–157.
38. Pearson E. J. M. (2009). Comfort and its measurement – A literature review. Disability and Rehabilitation: Assistive Technology, 4(5), 301-310.
39. Reiter, J. (2005). Deciphering the complexities of diagnosing and treating insomnia. Psychiatr. Times, 22, 74–76.
40. Roth, T. and Ancoli-Israel S. (1999). Daytime consequences and correlates of insomnia in the United States: Results of the 1991 National Sleep Foundation Survey. II. Sleep: Journal of Sleep Research & Sleep Medicine, 22 (Suppl 2), S354-S358.
41. Tamura, T., Miyasako, S., Ogawa, M., Togawa, T., Fujimoto, T. (1999). Assessment of bed temperature monitoring for detecting body movement during sleep: comparison with simultaneous video image recording and actigraphy. Medical Engineering & Physics, 21, 1-8.
42. Townsend, D., Holtzman, M., Goubran, R., Frize, M., Knoefel, F. (2011). Relative thresholding with under-mattress pressure sensors to detect central apnea. IEEE Transactions on Instrumentation and Measurement, 60(10), 3281-3289.
43. Verhaert, V., Haex, B., De Wilde, T., Berckmans, D., Verbraecken, J., Valck, E., Sloten, J. S. (2011). Ergonomics, 54(2), 169-178.