臺灣博碩士論文加值系統

小型風力發電機由於成本考量與可改裝空間較少之故，大部分都採用無控制或失速控制方式，但因為無法擷取額定風速以上的風能，在發電效率上尚有改進空間，本文旨在發展主動控制2kW小型風力發電機組的設計及實驗原型系統，以改善小型風力發電機的發電性能。
本文以東元2kW被動式小風機為基礎，首先發展創新機構葉片變旋角機構及主動式變旋角控制系統，利用直流伺服馬達驅動葉片傘形齒輪機構，並搭配PID旋角控制器，以一傘齒輪帶動三個從動傘齒輪，改變風機葉片旋角。其次建立小風機的全機系統數學模型，並以FAST、ADAMS與MATLAB軟體模擬小風機的全機性能，並發展葉片變旋角控制器及發電機轉子定轉速控制器，並先以模擬驗證創新葉片變旋角定位系統與發電機轉子定轉速控制系統。
實驗原型系統以東元2kW被動式小風機進行機構及控制系統改裝，以PID控制及模糊滑動平面控制的閉迴路控制，包括葉片的變旋角(pitch angle)控制與發電機的轉子定轉速控制，並於開放式風洞進行實測，實現2kW小型風力發電機在額定風速之上時，利用直流伺服馬達的傘齒輪帶動三個從動傘齒輪，改變風機葉片旋角，並調整葉片的旋角使風機維持在額定轉速，保持額定功率的輸出，實現2kW小型風力發電機的主動控制。

Most of the small wind turbines are designed with no control or passive control due to the cost consideration so that the electric generation performance is limited as the wind speed is over the rated wind speed. Thus, the objective of the paper is to improve the electric generation performance by developing a novel active pitch control system and a rotor constant rotational speed control for a 2kW small wind turbine.
The study first developed a novel mechanism design for the active-controlled pitch control system. The novel mechanism is the DC servo motor-driving variable-pitch bevel mechanism. By using the PID controller, the one to three bevel gear chain driven by DC servo motor is applied to adjust the pitch angles of the three blades at the same time. Then, the dynamic simulation of the overall system of wind turbine was developed by combining softwares of FAST, ADAMS and MATLAB. After that, the proposed novel mechanism design of the active pitch control and the constant rotational speed control of rotor could be verified via dynamic simulation. For that, the controllers of pitch control and the constant rotor constant rotational speed control were developed by PID control and fuzzy sliding mode control.
The experimental prototype system was modified according to the TECO 2kW small wind turbine which original type has no control. The novel mechanism for the active pitch control system and the required controller system were integrated and tested in the open wind tunnel. When the wind speed is above the rated wind speed, the DC servo motor-driving variable-pitch control system starts to work to regulate the pitch angle to keep the constant rotational speed of rotor. The one to three bevel gear chain driven by DC servo motor is applied to adjust the pitch angles of the three blades at the same time. Through the active pitch control system, the constant rotational speed control of rotor can be implemented.

致謝 I
摘要 II
Abstract III
目錄 IV
圖目錄 VII
表目錄 X
第一章 緒論 1
1-1 前言 1
1-2 文獻回顧 2
1-2-1 風力發電機旋角控制系統回顧 2
1-2-2 小型風力發電機回顧 3
1-3 研究動機 4
1-4 本文架構 6
第二章 2kW風力發電機創新主動式旋角控制系統機構 8
2-1 風力發電機原理 8
2-2 創新主動式旋角控制系統機構 10
2-2-1 DC伺服馬達介紹 14
2-2-2 主動控制旋角機構 16
第三章 風力發電機之非線性數學模式 23
3-1 葉片翼型升力、阻力與變距力矩係數 23
3-2 傳動系統數學模式 29
3-3 葉片變旋角系統 30
3-3-1 直流伺服馬達數學模型[35] 31
第四章 控制理論與策略 35
4-1 2kW風力發電機控制策略 35
4-2 PID控制理論 36
4-3 模糊滑動控制 38
4-3-1 建立歸屬函數 40
4-3-2 解模糊化規則 43
4-3-3 參數α、Φ、u0與Gu 設定 44
第五章 模擬結果與討論 46
5-1 葉片變旋角定位控制系統模擬 46
5-2 發電機定轉速控制系統模擬 49
第六章 實驗結果與討論 56
6-1 葉片變旋角定位控制系統實驗 56
6-2 風力發電機定轉速控制系統實驗 59
6-2-1 發電機開迴路轉速測試實驗 62
6-2-2 發電機定轉速控制實驗 64
6-2-2-1 發電機轉子定轉速40rpm實驗 67
6-2-2-2 發電機轉子定轉速60rpm實驗 69
6-2-2-3 發電機轉子定轉速80rpm實驗 71
6-2-2-4 發電機轉子定轉速100rpm實驗 73
6-2-2-5 發電機轉子定轉速120rpm實驗 75
6-2-2-6 發電機轉子定轉速40~60rpm實驗 77
6-2-2-7 發電機轉子定轉速60~80rpm實驗 79
6-2-2-8 發電機轉子定轉速80~100rpm實驗 81
第七章 結論與未來展望 84
7-1 結論 84
7-2 未來展望 84
參考文獻 85
附錄A 88

[1]S.-r. Ali-Reza, "Discrete-time blade pitch control for wind turbine torque regulation with digitally simulated random turbulence excitation," Ph.D., Oregon state university, 1986.
[2]S. M. B. Wilmshurst, "Control strategies for Wind turbines," Wind Engineering, vol. 12, pp. 236-249, 1988.
[3]L. .Kendall, M. J. Balas, and Y. J. Lee, "Application of proportional-integral and disturbance accommodation control to variable speed variable pitch horizontal axis wind turbines," Wind Engineering, vol. 21, 1997.
[4]J. B. Freeman and M. J. Balas, "Direct model reference adaptive control of a variable speed horizontal axis wind turbines," Wind Engineering, vol. 22, 1998.
[5]M. Idan and D. Lior, "Continuously variable speed wind turbine: transmission concept and robust control," Wind Engineering, vol. 24, pp. 151-67, 2000.
[6]Y. D. Song, B. Dhinakaran, and X. Y. Bao, "Variable speed control of wind turbines using nonlinear and adaptive algorithms," Journal of Wind Engineering and Industrial Aerodynamics, pp. 293-308, 2000.
[7]T. Ekelund, "Yaw control for reduction of structural dynamic loads in wind turbines," Journal of Wind Engineering and Industrial Aerodynamics, pp. 241-262, 2000.
[8]E. Muljadi, K. Pierce, and P. Migliore, "Soft-stall control for variable-speed stall-regulated wind turbines," Journal of Wind Engineering and Industrial Aerodynamics, pp. 277-291, 2000.
[9]H. Guo and Q. Guo, "H infinity control of variable-speed adjustable-pitch wind turbine adjustable-pitch system," Electrical Machines and Systems, vol. 1, pp. 266 - 269, Nov. 2003.
[10]Z. Lin and G. Qingding, "Adjustable-pitch and variable-speed control of wind turbines using nonlinear algorithm," presented at the Sixth International Conference on Electrical Machines and Systems (ICEMS 2003), Nov. 2003.
[11]T. Senjyu, R. Sakamoto, N. Urasaki, T. Funabashi, H. Fujita, and H. Sekine, "Output power leveling of wind turbine Generator for all operating regions by pitch angle control," presented at the Energy Conversion, June 2006.
[12]X. Zhang, W. Wang, Y. Liu, and J. Cheng, "Fuzzy Control of Variable Speed Wind Turbine," presented at the Intelligent Control and Automation, June 2006.
[13]H. Liu, Y. Lin, and W. Li, "Study on Control Strategy of Individual Blade Pitch-Controlled Wind Turbine," presented at the Intelligent Control and Automation, June 2006.
[14]J. Yang, J. Li, J. Wu, and J. Yang, "Fuzzy Adaptive Control of Novel Brushless Doubly-fed Wind Turbine," presented at the Intelligent Control and Automation, June 2006.
[15]K. E. Johnson, L. Y. Pao, M. J. Balas, and L. J. Fingersh, "Control of variable-speed wind turbines: standard and adaptive techniques for maximizing energy capture," presented at the Control Systems Magazine, June 2006.
[16]H. Camblong, G. Tapia, and M. Rodriguez, "Robust digital control of a wind turbine for rated-speed and variable-power operation regime," presented at the Control Theory and Applications, Jan. 2006.
[17]Y. Qi and Q. Meng, "The Application of Fuzzy PID Control in Pitch Wind Turbine," Energy Procedia, vol. 16, pp. 1635-1641, 2012.
[18]A. G. Quynn, "Blade pitch control of a wind turbine," U.S. Patent, Apr. 1986.
[19]S. Oohara, M. Ichinose, M. Futami, K. Tsutsumi, T. Shiraishi, S. Yoshida, et al., "Wind turbine and wind turbine rotor pitch control method," Europe Patent, 2008.
[20]桂人傑, 童建強, and 張永源, "風力發電機之葉片旋角驅動裝置及其驅動方法," R.O.C. Patent, 2009.
[21]P. Brath and K. Z. Ostergaard, "Pitch control of a wind turbine," U.S.A. Patent, Dec. 2011.
[22]M. B. Andrews, "Wind turbine blade pitch control system," U.S.A. Patent, Oct. 1982.
[23]F. Scherillo, L. Izzo, D.P.Coiro, and D. Lauria, "Fuzzy Logic Control for a Small Pitch Controlled Wind Turbine," presented at the International Symposium on Power Electronics,Electrical Drives, Automation and Motion, 2012.
[24]B. M. Nagai, K. Ameku, and J. N. Roy, "Performance of a 3 kW wind turbine generator with variable pitch control system," Applied Energy, vol. 86, pp. 1774-1782, 2009.
[25]N. Nanayakkara, M. Nakamura, and H. Hatazaki, "Predictive control of wind turbine in small power systems at high turbulent wind speeds," Control Engineering Practice, vol. 5, pp. 1063-1069, 1997.
[26]H. Li, D. Zhang, and S. Y. Foo, "A Stochastic Digital Implementation of a Neural Network Controller for Small Wind Turbine Systems," presented at the IEEE Transactions on Power Electronics, Sept. 2006.
[27]財團法人台灣經濟研究院, "小型風力機城市應用現況與效能分析計畫(Small wind turbine city status and performance analysis of the application program)," 2013.
[28]林輝政, 江茂雄, 吳元康, 張淵智, and 蘇煒年, "2-3kW主被動控制小風機研發計畫," 2013.
[29]P. Delarue, A. Bouscayrol, A. Tounzi, X. Guillaud, and G. Lancigu, "Modelling, control and simulation of an overall wind energy conversion system," Renewable Energy, vol. 28, pp. 1169-1185, July 2003.
[30]牛山泉, 風車工學入門 從基礎理論到風力發電技術: 國立澎湖科技大學, 2009.
[31]Animatics. Available: http://tw.animatics.com/
[32]葉杭冶, 發電機電機組的控制技術: 機械工業出版社, 2005.
[33]G. Michalke, A. D. Hansen, and T. Hartkopf, "Control strategy of variable speed wind turbine with multiple permanent magnet synchronous generator," presented at the European Wind Energy Conference and Exhibition, Milano, May 2007.
[34]M. Yin, G. Li, M. Zhou, and C. Zhao, "Modeling of the Wind Turbine with a Permanent Magnet Synchronous Generator for Integration," presented at the IEEE, Power Engineering Society General Meeting, June 2007.
[35]劉羣章 and 許源浴, 電機機械: 中央圖書出版社, 1986.
[36]Y. P. Y. M.H. Chiang, F.L. Yang, Y.N. Chen, "Integrated control of clamping force and energy-saving in hydraulic injection moulding machines using decoupling fuzzy sliding-mode control," International Journal of Advanced Manufacturing Engineering, vol. 27, pp. 53-62, November 2005 2005.
[37]葉永培, "解耦合自組織模糊滑動平面控制應用於閥控液壓缸系統變排量節能控制與伺服控制之整合控制研究," 碩士論文, 國立台灣科技大學, 2003.
[38]林津, "主動控制2kW小型風力發電機組設計與分析之研究," 碩士論文, 國立台灣大學, 2015.